Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Installing Valve Boosters  (Read 2332 times)

0 Members and 1 Guest are viewing this topic.

A.J. Walker

  • Good talker
  • **
  • Offline Offline
  • Posts: 58
Installing Valve Boosters
« on: October 03, 2014, 04:11:41 PM »

I've been refurbishing a 1920s 3-row hohner and replaced all the valves with new leather. Not played yet; have some other fiddly bits to do. Since then, I've realized it might be better if the bass valves had boosters.

Can these be added to the leathers while they're on the reed plates? These are screwed to gaskets so I won't be dealing with unwaxing and re-waxing.
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Installing Valve Boosters
« Reply #1 on: October 04, 2014, 04:28:27 PM »

Yes, that should work fine if you're careful.  I have only done it once, and seem to recall sticking the 'dots' (punched out of bellows tape) in position with tweezers while the other hand holds the booster centered.  I used contact cement.

Hopefully someone more knowledgeable can confirm.
Logged

911377brian

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1518
Re: Installing Valve Boosters
« Reply #2 on: October 04, 2014, 04:46:40 PM »

What are valve boosters? ???
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Installing Valve Boosters
« Reply #3 on: October 04, 2014, 05:15:16 PM »

What are valve boosters? ???
They are the 'springs' which are attached to the larger leather or vinyl valves on the bigger reeds in order to ensure that in the resting position the valves lie flat against the reed plate. They can either be of the 'dot and steel spring' type, usually fitted to leather valves, or extra leaves of vinyl strip which are more often found attached to synthetic leather ('vileda') valves.

Pictures here and here, although the latter is a bit difficult to see clearly - there are transparent vinyl strips fixed to the vileda valves.

Without the springs or boosters, the larger valves tend to lift when the adjacent reed is being sounded which can sometimes result in an unwanted valve 'flutter' -  a low-pitched rumbley sort of sound overlaid on the proper reed note.

Edited to correct typo, sorry.
« Last Edit: October 04, 2014, 05:21:58 PM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Installing Valve Boosters
« Reply #4 on: October 04, 2014, 05:18:26 PM »

I noticed many on my green buttoned Pariselle and wondered why.
 Now I know Steve, thanks for that.
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Installing Valve Boosters
« Reply #5 on: October 04, 2014, 05:27:18 PM »

I fit these as follows:
1)Place a spot of glue on the valve
2) place the booster with one end on the glue,
3) place the paper dot on top if the booster and glue
Job done
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

911377brian

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1518
Re: Installing Valve Boosters
« Reply #6 on: October 04, 2014, 05:44:30 PM »

Theo and Steve, many thanks....
Logged

A.J. Walker

  • Good talker
  • **
  • Offline Offline
  • Posts: 58
Re: Installing Valve Boosters
« Reply #7 on: October 04, 2014, 07:22:23 PM »

Thanks all. The boosters I bought actually have the dots pre-attached to the booster.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal