Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Spindle hole  (Read 5988 times)

0 Members and 1 Guest are viewing this topic.

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Spindle hole
« on: October 06, 2014, 11:51:39 PM »

Does anyone know the technique for drilling a spindle hole on a keyboard? Or is it a matter of making up a keyboard from drilled parts and assembling it with a spindle in situ, to get it all to line up.
I can't see how you would drill a long hole with a small but very long drill - surely it would flex and drift?

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Spindle hole
« Reply #1 on: October 07, 2014, 12:56:03 AM »

How the makers do this I'm unsure, but assuming no really wild grain, I would do this on a lathe, packing the keyboard up to the right height to slide along the bed and putting a centre pop at both ends where the hole enters and exits, then using the tailstock centre to push the keyboard into the drill, which needs to be accurately sharpened.

Frequent withdrawals to evict swarf are essential to prevent swarf packing the drill and causing it to wander although the keyslots probably make this less of an issue than a solid block.

Extending jobber drills is not a major problem (if you know a model engineer who works for beer  :|glug)

Doing this through three feet of steel gun barrel blank takes a bit more effort and a much longer drill..........

Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Spindle hole
« Reply #2 on: October 07, 2014, 01:04:59 AM »

One way seen on wooden keyboards is to make a saw kerf (rather than a hole) running the length of the bottom of the keyboard.  The spindle goes to the bottom of the kerf and small blocks of wood are glued in the kerf to keep the spindle in place.

All I could find is a picture of a bass end mechanism, without the small blocks, but at least you can see the kerf.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Spindle hole
« Reply #3 on: October 07, 2014, 06:33:57 AM »

Thanks.
I've not really investigated drill bits but at first glance it looks like 3mm, 300mm long drill bits are available. I don't have a lathe so I wonder if there is any way to do it without?
(Luckily I'm not boring out a gun barrel).

I'd forgotten about the kerf idea. Would need pretty fine blade to do it, but I can see how it would work.

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Spindle hole
« Reply #4 on: October 07, 2014, 06:38:34 AM »

Without a lathe or a tower drill Rog, it sounds like a nightmare waiting to happen. I've noticed at times that even a tower drill can wander. The kerf idea sounds great and watchmakers tools may be the answer.
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Spindle hole
« Reply #5 on: October 07, 2014, 07:30:52 AM »

One way seen on wooden keyboards is to make a saw kerf (rather than a hole) running the length of the bottom of the keyboard.  The spindle goes to the bottom of the kerf and small blocks of wood are glued in the kerf to keep the spindle in place.
I can confirm that this is the method we used on the Emmanuel Pariselle's one-row melodeon building course.
The attached photo shows the keyboard assembly under construction belonging to Paul Johnson (formerly of this parish, who sadly died suddenly in April 2014).

You can see the saw cut on the end section of the keyboard. The saw cut is then covered over by gluing a thin wooden top plate in place. I'm not certain of the purpose of the odd-shaped walnut jig thing sitting on top of the keyboard assembly; I confess I've forgotten!

Paul and I were work buddies on the 2008 course and he was meticulous in photographing his work as it progressed. Photos of the 2008 course can be viewed on Paul's still active Flickr account here and here.

Paul was a lovely gentle man and a good friend. He is much missed.

Edited to add additional link to more of Paul's melodeon building photos.
« Last Edit: October 07, 2014, 11:28:08 AM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Spindle hole
« Reply #6 on: October 07, 2014, 10:26:56 AM »

Hi Steve, thanks.  Also a nice but sad story about your work buddy.

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Spindle hole
« Reply #7 on: October 07, 2014, 12:45:32 PM »

The jig looks like a spacer, it's shown in another photo.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Spindle hole
« Reply #8 on: October 07, 2014, 01:41:29 PM »

Emmanuel is the world's master of the jig. He has one for practicely everything.
« Last Edit: October 07, 2014, 04:10:03 PM by Nick Collis Bird »
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Spindle hole
« Reply #9 on: October 07, 2014, 01:44:25 PM »

The jig looks like a spacer, it's shown in another photo.
You're right Malcolm. I'm fairly sure now that it is a gauge for getting the action spring anchoring screw at just the right depth of insertion.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Spindle hole
« Reply #10 on: October 07, 2014, 03:23:37 PM »

Not too sure about that, Steve. I think it may be for marking the exact position of the holes for the buttons. Slide it into the slot and drill through the locating hole. The brass screw is for fine adjustment.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

boxer

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 380
  • B/C Pokerwork - ultimate ceili box
Re: Spindle hole
« Reply #11 on: October 07, 2014, 04:59:02 PM »

I've wondered about this myself.

Old-fashioned spoon bits, although very inefficient, have the virtue of being self-centering.  I wounder if they were ever used for this purpose?
Logged
Nuage, Tommy, Cairdin, 
Double Ray DLX 21x12, Black Dot,
Pre-Erica, Pokerwork
plus various stringed things

baz parkes

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1894
    • All Blacked Up
Re: Spindle hole
« Reply #12 on: October 07, 2014, 05:06:32 PM »

Emmanuel is the world's master of the jig. He has one for practicely everything.

What...32, 48 and 64... :D

(Coat...me..get..)
Logged
On the edge of Cheshire's Golden Triangle, apparently...

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Spindle hole
« Reply #13 on: October 07, 2014, 05:17:44 PM »

Not too sure about that, Steve. I think it may be for marking the exact position of the holes for the buttons. Slide it into the slot and drill through the locating hole. The brass screw is for fine adjustment.
Aha! Thanks, Rees.
That makes more sense. I have no recollection of using this device when I made my one-row. (which perhaps explains why the keyboard holes are very slightly out of line with each other - though you do have to look very hard to notice  :|bl )
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

TomB-R

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 598
Re: Spindle hole
« Reply #14 on: October 07, 2014, 05:25:30 PM »

I've used the "drill individual blocks in a jig, thread them on the spindle then glue them into place" method, which worked fine.
If that's not an option, I'd wonder about using a jig which is moved from gap to gap as the drill progresses, so as to reguide the drill, OR a jig with a small spike to remark the entry point as the drill crosses each gap ( perhaps with a bit of manual persuasion.)

I'd be impressed with a hole drilled accurately through the solid before the key spaces are cut, but I see gun drills "can" go to 300:1 length/bore.
Tom

Logged

Foma

  • Member
  • *
  • Offline Offline
  • Posts: 21
    • Гармонь
Re: Spindle hole
« Reply #15 on: October 07, 2014, 09:09:17 PM »

 Jig:


Drill - spica, tip exiled.
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Spindle hole
« Reply #16 on: October 07, 2014, 09:44:45 PM »

The saw kerf method is by far the easiest and most accurate.

Cut the kerf, glue a piece on top and finally cut the slots for the levers. Job done.
« Last Edit: October 07, 2014, 09:46:18 PM by Rees »
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Spindle hole
« Reply #17 on: October 07, 2014, 10:46:40 PM »

Emmanuel is the world's master of the jig. He has one for practicely everything.

He may be one of the world's masters of the jig but I think there are many up there with him, from a few years of personal experience I would cite Martyn Banks of Oakwood Instruments as one such but his skills carry across a variety of instruments far more complex than the melodeon. Olaf Bergflodt is no slouch when it comes to melodeons either, his designs are inovative and beautifully executed. The list is probably going to be very long so it's easier to accept that Emmanuel is one of the gifted.  :D
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Spindle hole
« Reply #18 on: October 08, 2014, 01:02:03 AM »

If you don't have access to a lathe I think the cut and cover method suggested (kerf then fill with a veneer) is probably your best bet at getting this right first time - those Japanese pull saws have the right sort of kerf width, are pretty controlable and a pair of guide blocks fitted either end would take out a lot of variables in one fowl swoop  ;D

I've never seen a spoon bit this small but yes they are pretty tolerant of grain / density variations, as are the Forstner type bits (which cut on the outer edge) used these for the replacement end plates on the early Hohner I'm restoring - originally punched.
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Spindle hole
« Reply #19 on: October 08, 2014, 01:25:37 AM »

You don't need a pull saw or veneer.
Run the axle block over a 3mm wide circular saw blade set at a depth of 3mm. Glue another piece of wood (3 or 4mm thick) over the top of the whole width of the lever slots to create a 3mm square hole. Then cut the lever slots.
Use a 3mm axle rod.

I'm not explaining this very well but Steve's pic illustrates it perfectly.

Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal