Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Spindle hole  (Read 5969 times)

0 Members and 1 Guest are viewing this topic.

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Spindle hole
« Reply #20 on: October 08, 2014, 02:03:45 AM »

Bet your boxes will not need the axle rod 'cooked' with a car battery to release them in a century Rees  ;)

Don't run to a circular saw here otherwise I might have worked that out :|bl
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

TomB-R

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 598
Re: Spindle hole
« Reply #21 on: October 08, 2014, 09:22:04 AM »

You don't need a pull saw or veneer.
Run the axle block over a 3mm wide circular saw blade set at a depth of 3mm. Glue another piece of wood (3 or 4mm thick) over the top of the whole width of the lever slots to create a 3mm square hole. Then cut the lever slots.

You're inciting saw envy Rees!
Tom
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Spindle hole
« Reply #22 on: October 08, 2014, 09:50:20 AM »

Jig:


Drill - spica, tip exiled.

I'm liking the 'cut and shut' technique, but Foma's diagram is intriguing. Assume there is a brass insert in the jig to get the drill started in the right place for each slot.

Foma

  • Member
  • *
  • Offline Offline
  • Posts: 21
    • Гармонь
Re: Spindle hole
« Reply #23 on: October 08, 2014, 02:17:43 PM »

More way:


Repair


before



after
Logged

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 613
Re: Spindle hole
« Reply #24 on: October 10, 2014, 02:21:10 PM »

 Foma ; looks like you are able to make this kind off key boards from scratch? I have being looking for a replacement key board for my 4 stop chines made Cajun box will you be able help out  :||:? I still have the old one -well partially -     
« Last Edit: October 13, 2014, 10:46:47 AM by invadm »
Logged

Foma

  • Member
  • *
  • Offline Offline
  • Posts: 21
    • Гармонь
Re: Spindle hole
« Reply #25 on: October 10, 2014, 04:00:56 PM »

Need a model or drawing,for example:

Logged

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 613
Re: Spindle hole
« Reply #26 on: October 13, 2014, 10:48:30 AM »

Need a model or drawing,for example:


I can upload some photos of the key board or can e-mail you more photos if you can help?
Logged
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal