Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Removing metal corners on bellows frames - and putting them back.  (Read 2036 times)

0 Members and 1 Guest are viewing this topic.

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.

Early Hohner and Koch "2915" boxes, with the wide bellows frames, have metal corners held on with metal pins. The one in the photo has one large pin and two smaller.

Anyone recommend a sensible way to get them out without trashing them, to re-cover the frame? Also suggest a source of replacement pins (upholstery suppliers?) for replacement?

Thanks
Malcolm
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Removing metal corners on bellows frames - and putting them back.
« Reply #1 on: October 25, 2014, 12:33:42 AM »

Removal - slide a flat blade under the edge and lever upwards, gradually working around all sides.
Hohner reed block nails make good replacements. I have a box full if you need any.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Removing metal corners on bellows frames - and putting them back.
« Reply #2 on: October 25, 2014, 12:36:39 AM »

I have ten boxes full if you need any more  ;)
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

A.J. Walker

  • Good talker
  • **
  • Offline Offline
  • Posts: 58
Re: Removing metal corners on bellows frames - and putting them back.
« Reply #3 on: October 25, 2014, 04:27:34 AM »

I was considering such a task for a 1920s Hohner I have. The points of the brads/round-headed nails/whatever stick through the other side of the wood case (in mine anyway). Tapping the protruding end with a hammer might push them out a bit and make it easier to pry them out from the outside. Perhaps they can be re-used. No, I haven't tried this yet.
Logged

Suppards

  • Good talker
  • **
  • Offline Offline
  • Posts: 84
  • Old enough to know better. Daft enough not to care
Re: Removing metal corners on bellows frames - and putting them back.
« Reply #4 on: October 25, 2014, 04:29:06 AM »

I have ten boxes full if you need any more  ;)

Oooh! - I sense tension.  But whose spare Hohner reed block nails are the best?  There's only one way to settle this one lads - melodeons at dawn!   ;)

(My money is on Theo. Rees will just wake up one morning to find his thread has been moved somewhere dark, dismal and on the outer reaches of the known world.  Oh hang on....he's already in Wales   (:))
Logged
Steve
North Yorkshire, UK

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Removing metal corners on bellows frames - and putting them back.
« Reply #5 on: October 25, 2014, 12:20:36 PM »

Now then .............
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Removing metal corners on bellows frames - and putting them back.
« Reply #6 on: October 25, 2014, 12:35:15 PM »

Thanks for the replies & offers. This job is still some way off, so I imagine Theo and Rees might have a couple more by then...

Oddly enough, I can quite see myself religiously removing these pins then religiously storing them for ever - one of the reasons it took so long to clear out my garage for conversion! Even then I gave away, Ebay'd and Freecycled all sorts of stuff just so it didn't go to the dump.

I do like the look of these old boxes, somebody had an immaculate one on Ebay.de some months back in red and it looked very striking. Also, I think somebody here restored one, not so long ago, but I haven't found the thread yet.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Removing metal corners on bellows frames - and putting them back.
« Reply #7 on: October 25, 2014, 01:24:54 PM »

I did one not so long ago. Took ages to track down some Rexine of the right colour and texture to re-cover the bellows, with help from Nick CB. 
Here is the finished box.  Pity I only had a black fingerboard.
« Last Edit: October 25, 2014, 03:36:54 PM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Removing metal corners on bellows frames - and putting them back.
« Reply #8 on: October 25, 2014, 11:56:48 PM »

Hi Malcolm

A close encounter with the bit of a soldering iron on the nail head may help, I've just done a similar removal of the bone / ivory label on a neighbours microscope box and as an added precaution waved a hot air gun over the label just in case it was actually celluloid and brittle.

A useful tool can be made from a thin old fashioned bone handled dining knife, grind the rounded end down to about a 70 degree included angle and then grind or stone a fine chisel end on it, I find that this can be forced under the pinned item until it touches the pin and you can then tap the handle with a small hammer or mallet, at varying angles, which tends to powderise the rust and render the pin more amenable to parting company with the wood.
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Removing metal corners on bellows frames - and putting them back.
« Reply #9 on: October 26, 2014, 12:13:32 AM »

Oddly enough, I have several such implements to hand. The grinder is securely packed in storage, the workpiece is two feet away... Sounds like a plan.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Removing metal corners on bellows frames - and putting them back.
« Reply #10 on: October 26, 2014, 12:44:06 AM »

I have a variety of such sacrificial precision cold chisels from a former life repairing leaded / stained glass Malcolm, despite having been modified pre 1985 I think only one has actually been destroyed beyond repair by such abuse - make wicked scrapers too !

(Thinks, says something for the quality of Sheffields cutlery of years gone by)

((Thinks again - for the more advanced tinkerer, grinding 2/3rds into one with a narrowish angle grinder blade thus forming a little hook makes a very useful tool with a multitude of uses, mine is mainly used for slitting plastic baggies for those times when only 2 into 1 will do !))
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Removing metal corners on bellows frames - and putting them back.
« Reply #11 on: October 26, 2014, 01:14:07 AM »

I have a number with stainless blades, for odd jobs. A few with carbon steel blades, they are hard to get now, for specialist cutting. The stainless take a reasonable edge, for stainless, and are what I expect to use to follow Theo's and your suggestions. Probably unsharpened, though! ;D
Raided Wimborne Market a few months back to stock up. 
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal