Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Question about varnish and wax finish  (Read 3947 times)

0 Members and 1 Guest are viewing this topic.

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Question about varnish and wax finish
« on: November 08, 2014, 12:44:52 AM »

Hi, can anyone out there who has attended a Pariselle course remind me of how the wood is finished?From memory, three or so coats of varnish were applied, with wire wool rubbings in between coats. The bit I can't remember is if the last varnish coat is wire wooled before the wax polish was applied, and/or if the wax was also wired wooled? And doesn't the wool scratch the varnish, and if you see scratches after a coat of varnish, what to do next?
I've just tried this approach with water based (acrylic) varnish, and it worked ok ...ish (on a scrap piece of wood). I need to try it again, but maybe with longer between coats. The end result showed little scratches from the final wire wooling just before waxing.

I am of course aware that the varnish on the Pariselle course wasn't the water based acrylic stuff, so maybe that's where I have  a problem.
« Last Edit: November 08, 2014, 07:54:24 AM by RogerThomas »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Question about varnish and wax finish
« Reply #1 on: November 08, 2014, 09:13:06 AM »

You also need the correct, very fine, grade of steel wool.  The stuff you find in most diy ships is likely to be too coarse.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Question about varnish and wax finish
« Reply #2 on: November 08, 2014, 09:31:46 AM »

If it's anything like violin varnish, the final buff before waxing usually consists of an application of jeweller's rouge and then a cutting compound such as T-Cut. On my string instruments I usually use 2000 grit (or finer, if I can get it) wet-and-dry rather than steel wool, but either will do the job.  Never tried it with acrylic varnish, but I don't see why cutting compound shouldn't work equally well with it. In my experience, however, acrylic varnishes tend to leave more noticeable brushmarks than shellac or oil based ones and will probably need more rubbing down and probably more coats than a traditional instrument varnish.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Question about varnish and wax finish
« Reply #3 on: November 08, 2014, 11:09:18 AM »

On the most recent Emmanuel Pariselle course a couple of weeks ago, I'm pretty sure the varnish used was Ronseal clear interior satin or something very similar. The varnishing regime was as follows:

  • Sand bare wood, finishing with 240 grade carborundum paper. Some people went further and finished with 400 grade, but mostly 240 grade was sufficient.
  • Apply two coats of varnish, rubbing down in between with 400 grade carborundum and/or 0000 grade (very fine) steel wool.
  • After the final coat of varnish, a light rubbing down with 0000 steel wool, followed by buffing to a semi-matte shine using a soft cotton cloth.

Comes up bootiful...  (:)

 
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Question about varnish and wax finish
« Reply #4 on: November 08, 2014, 11:25:25 AM »

Ah. Thanks for the info. And I did not know you can get different grades of wire wool. And you a right about the brush strokes. I'm just experimenting a bit with finishes

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Question about varnish and wax finish
« Reply #5 on: November 08, 2014, 12:10:08 PM »

I used to use Garnet paper, then wet and dry, between coats. I also experimented, fairly successfully with applying the final coat of varnish, slightly warmed, with my fingers.

John
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Question about varnish and wax finish
« Reply #6 on: November 08, 2014, 12:13:08 PM »

On the most recent Emmanuel Pariselle course a couple of weeks ago, I'm pretty sure the varnish used was Ronseal clear interior satin or something very similar.

No, sorry Steve you are way off, not even similar.   We used Rustins Plastic Coat.  A two part finish which produces the most durable finish of any clear finish I know.  I did my wooden kitchen woorktops with it and after 2 years it is unmarked.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Question about varnish and wax finish
« Reply #7 on: November 08, 2014, 02:41:28 PM »

Yes, I thought I'd try the cheaper water based option first, because the Rustins stuff is quite expensive. But it was probably a false economy.

Bob Ellis

  • Hero?....Where's my medal, then?
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2878
  • Ain't I cute?
Re: Question about varnish and wax finish
« Reply #8 on: November 08, 2014, 04:14:14 PM »

On the 2.6 row course I attended in 2011, Emmanuel supplied spray cans of a French varnish called Julien. I bought a can so that I could touch up the finish if it wore down, but so far, after three years' almost continuous playing, I haven't need to use it on my box, so it is obviously hard-wearing. However, I have used it with good results on other things, including a tabor drum.
Logged
Bob in beautiful Wensleydale, Les Panards Dansants, Crook Morris and the Loose Knit Band.
Clément Guais 3-row D/G/acc.; Castagnari 1914 D/G; Karntnerland Steirische 3-row G/C/F; Ellis Pariselle 2.6-row D/G/acc.; Gabbanelli Compact 2-row D/G with lots of bling, pre-war Hohner Bb/F; Acadian one-row in D.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Question about varnish and wax finish
« Reply #9 on: November 08, 2014, 04:39:18 PM »

Bob

That spray finish was only used on a few late finished items such as grills, and some fingerboards. The main parts were all done with Rustins.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Bob Ellis

  • Hero?....Where's my medal, then?
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2878
  • Ain't I cute?
Re: Question about varnish and wax finish
« Reply #10 on: November 08, 2014, 04:50:28 PM »

Oh! I had forgotten that until you reminded me. :|bl
Logged
Bob in beautiful Wensleydale, Les Panards Dansants, Crook Morris and the Loose Knit Band.
Clément Guais 3-row D/G/acc.; Castagnari 1914 D/G; Karntnerland Steirische 3-row G/C/F; Ellis Pariselle 2.6-row D/G/acc.; Gabbanelli Compact 2-row D/G with lots of bling, pre-war Hohner Bb/F; Acadian one-row in D.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Question about varnish and wax finish
« Reply #11 on: November 08, 2014, 04:59:05 PM »

I remember because I did a lot of the varnishing!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Question about varnish and wax finish
« Reply #12 on: November 08, 2014, 05:16:51 PM »

On the most recent Emmanuel Pariselle course a couple of weeks ago, I'm pretty sure the varnish used was Ronseal clear interior satin or something very similar.

No, sorry Steve you are way off, not even similar.   We used Rustins Plastic Coat.  A two part finish which produces the most durable finish of any clear finish I know.  I did my wooden kitchen woorktops with it and after 2 years it is unmarked.
Aha - thanks for the correction Theo - I got confused between Rustins and Ronseal. They both start with 'R'. I remember you telling me about your kitchen worktops.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Question about varnish and wax finish
« Reply #13 on: November 08, 2014, 05:44:09 PM »

In my furniture making days the easiest finish to apply was a pre catalyzed lacquer - quick drying, wipe on finish (or spray). I found almost impossible to get runs etc.

This sort of stuff - http://www.wood-finishes-direct.com/product/pre-cat-lacquer
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Question about varnish and wax finish
« Reply #14 on: November 08, 2014, 05:45:46 PM »

Aha - thanks for the correction Theo - I got confused between Rustins and Ronseal. They both start with 'R'.

Pirate varnish. 8)
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Question about varnish and wax finish
« Reply #15 on: November 08, 2014, 06:09:19 PM »

Took a few seconds. Ouch.  ;D
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: Question about varnish and wax finish
« Reply #16 on: November 08, 2014, 06:23:23 PM »

Not only are there different grades of steel wool, there are different qualities.

The usual stuff is short fibers and oiled.

The good stuff is long fiber and not oiled. This is a cabinet makers grade.

If you do use steel wool.. make sure you wipe it all off as it will react with finishes.
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Question about varnish and wax finish
« Reply #17 on: November 08, 2014, 06:27:35 PM »

I use this stuff available in many grades, 0000 is good for finishing varnish etc.

pete /acorn

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 930
  • .Cast Trilly
    • Acorn Instruments
Re: Question about varnish and wax finish
« Reply #18 on: November 08, 2014, 07:22:24 PM »

Hi
Whatever you use,steel wool,nylon finishing pads etc etc,buy a box of tack cloths and wipe over befor applying finish.

also be very careful if you use any silicon spray polishes in your house,do not let any cloths that have been near the stuff near anything to be polished.

Pete
Logged
Acorn Instruments are specialist retailers of Castagnari Instruments,and have an extensive stock of new instruments on the shelf for prompt delivery in standard layouts however these can easily be changed to customers special requirements,we have over 600 reeds in stock
 We also have the largest stock in the UK of  pre loved melodons all fully serviced,and with 12 months warranty
UK and international customers catered for
www.acorninstruments.co.uk

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Question about varnish and wax finish
« Reply #19 on: November 12, 2014, 08:32:06 AM »

Thanks everyone for their advice. Very helpful.
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal