Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Bellows pins  (Read 2520 times)

0 Members and 1 Guest are viewing this topic.

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Bellows pins
« on: November 11, 2014, 01:09:41 PM »

Just replaced the gaskets on my Corona II. Having great problems getting the bellows pins fully inserted. They are more like nails than the pins I've encountered elsewhere, and are slightly rusty on the top half, bit below the head.
Is this normal, and should I replace them?


John
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Bellows pins
« Reply #1 on: November 11, 2014, 01:16:40 PM »

I suspect that you need ensure you have compressed the gasket, it being new. I usually place the bass end against the edge of my bench and push against the treble end then insert the pins. If they are not going in relatively easily they are probably misaligned. Did you mark the bellows to ensure they are gong back on in the same position from which they were removed?

I normally put corroded pins in the chuck of my Dremel and run some abrasive against the pin to remove the corrosion.

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Bellows pins
« Reply #2 on: November 11, 2014, 01:57:47 PM »

Thanks for that Lester. I need to get some felt washers from Charlie, so I will get replacement pins at the same time. I didn't make sure they went back in the same holes (Silly me), but I have tried rotating them to different holes, to no good effect.  I did stand the box on it's feet, and press down hard to compress the gaskets, didn't help much I'm afraid.
On another subject; is Copydex OK to use as an adhesive for refacing pallets? (I don't mind the smell  :-X )


John
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Bellows pins
« Reply #3 on: November 11, 2014, 02:39:25 PM »

Copydex is ok if you don't mind the facings falling off after some years. Pva is much better.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Bellows pins
« Reply #4 on: November 11, 2014, 02:40:13 PM »

John, don't use copydex for anything. It turns into a slimy mess in a very short while. A PVA or Botstick type maybe better. There are threads on this subject on here somewhere.
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Bellows pins
« Reply #5 on: November 11, 2014, 03:29:42 PM »

On another subject; is Copydex OK to use as an adhesive for refacing pallets? (I don't mind the smell  :-X )
As Nick and Theo have both said, don't use Copydex. It's horrible stuff and eventually turns into latex goo
For gluing new pallet facing on to the pallets I prefer to use Bostik clear contact adhesive rather than PVA. Both do the job well and will form a lasting bond. But I can't help feeling that at some point in the future, someone might want to replace the facing again, in which case the Bostik is going to be easier to clean off the pallet wood compared with the PVA which sets rock-hard.

Whichever adhesive you decide to use, just spread a single thin coating on the pallet wood surface only, and immediately press on to the felt backing of the pallet facing. Do all the pallets in one go, arranging them side-by-side on the felt with a tiny gap between them - just enough to slip in the blade of a craft knife or scalpel. Cover with a strip of waste wood and place under a moderate weight (a few dictionary-size books) for an hour or so. Then use your knife/scalpel (ensure it's sharp!) to separate the individual pallets.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Bellows pins
« Reply #6 on: November 11, 2014, 04:47:11 PM »

Thanks Steve, in this instance it's a spoon off a very old Hohner single row, I'm refacing.

John
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Bellows pins
« Reply #7 on: November 11, 2014, 04:48:59 PM »

Best material I've found for that is a nice soft leather about 2mm thick.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

nigelhughes552

  • New Starter
  • Offline Offline
  • Posts: 2
Re: Bellows pins
« Reply #8 on: December 03, 2014, 01:05:19 AM »

Hi

Just joined the forum - after some advice on bellows pins.

I've recently bought a Hohner single row from an auction with a view to repair it and learn to play. It seems in reasonable condition but some of the bellows pins have no heads. What's the best method of removing them? Do I try to drill them out or is it possible to push them further in in the hope they come out the other side?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Bellows pins
« Reply #9 on: December 03, 2014, 08:06:27 AM »

Drilling out is best avoided if possible as it will inevitably damage and enlarge the hole.  Pushing the pins in is better if you can do it, but, the most likely reason the heads are broken off the pins is that they are firmly rusted into place, so it could be difficult. Heating the pins with a hot soldering iron can help to loosen old rust.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

nigelhughes552

  • New Starter
  • Offline Offline
  • Posts: 2
Re: Bellows pins
« Reply #10 on: December 03, 2014, 02:15:31 PM »

Thanks for the advice I'll give it a go.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal