Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Hohner Chrome body corners - removal and fitting  (Read 1797 times)

0 Members and 1 Guest are viewing this topic.

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Hohner Chrome body corners - removal and fitting
« on: January 26, 2015, 11:41:45 PM »

I have a pre pokerwork Vienna style Hohner, plus a 114 Hohner and I want to replace the chrome corners, but I don't want to wreck the body when removing the old ones. The corners have a little right angle lip that slots into the body. Can someone advise on the method of removing these corners? I've tried gently shifting them with a wedge of hardwood and a light hammer but they refuse to budge. Is it a case of grabbing with pliers and pulling?  Also, what's the best way to fit replacements without destroying/damaging them and the body?
Thanks

OK perhaps should have looked a bit harder... I just found this thread...
http://forum.melodeon.net/index.php/topic,7556.msg93889.html#msg93889

However, if anyone has other tips I'd be grateful. Ta.
« Last Edit: January 27, 2015, 08:30:26 AM by RogerThomas »
Logged

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Hohner Chrome body corners - removal and fitting
« Reply #1 on: January 27, 2015, 12:58:37 PM »

I was just going to look for that thread when I saw your edit!

I was wondering if heating would help, although pondering about how to apply it.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hohner Chrome body corners - removal and fitting
« Reply #2 on: January 27, 2015, 01:24:08 PM »

I've done a number of these and do it thusly:

I place the casework so just the chrome bit over hangs the edge of my work bench with the closed end of the chrome bit lowermost. I then take a large flat bladed screwdriver and place it on the open end of the chrome bit and gently tap it off the box. Fitting the new one is done by gently tapping it into place using my little hammer and a block of wood. Both these tasks need doing gently and with plenty of checking that nothing untoward is happening.

ps I once had a box that was so badly corroded that gentle tapping would not budge the chrome bits, in the end I cut them along their length with a Dremel cutting disk and then removed them.

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Hohner Chrome body corners - removal and fitting
« Reply #3 on: January 27, 2015, 02:37:46 PM »

Thank you very much. Using a dremel I 'cleaned up' the terrible corners on my Modell II, leaving a lovely brass look, but though this matches marvellously with the yellow bellows paper, it doesn't look so good against the silver grille and bellows corners.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner Chrome body corners - removal and fitting
« Reply #4 on: January 27, 2015, 03:09:47 PM »

The brass corners do look nice polished up even when the plating is wearing off.  Steel ones not so good, and you would need to take steps to prevent further rust.  The new ones available now are stainless steel.
Incidentally the plating is not chrome, it is nickel.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Hohner Chrome body corners - removal and fitting
« Reply #5 on: January 27, 2015, 03:53:14 PM »

Ah thanks. Maybe I'll leave the brass corners as they are then. I was slightly holding back from publishing pictures of my pimped and declubbed Modell II for fear that it might be laughed at. However, it plays extremely well, with a very fast action...

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Hohner Chrome body corners - removal and fitting
« Reply #6 on: January 27, 2015, 03:58:01 PM »

Clacking away one doesn't  hope. >:E
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Hohner Chrome body corners - removal and fitting
« Reply #7 on: January 27, 2015, 04:03:33 PM »

Not really. It's been completely rebuilt/refaced, suited and booted.(:)
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal