Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Hohner Pokerwork - treble button return springs  (Read 4088 times)

0 Members and 1 Guest are viewing this topic.

steveh

  • Member
  • *
  • Offline Offline
  • Posts: 9
Hohner Pokerwork - treble button return springs
« on: February 07, 2015, 03:50:20 PM »

I've owned a second hand german made Hohner Pokerwork for about 4 years which I play regularly. It's a terrifc instrument but over the last 6 months, I've managed to break 3 button return springs. Has anybody else had a similar problem or have I just become very heavy handed? I just hope there's another explanantion! (:)
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Hohner Pokerwork - treble button return springs
« Reply #1 on: February 07, 2015, 04:07:25 PM »

They do seem to go several at a time.  I guess that just depends on how much work they're doing and what quality they are.  The early Chinese Pokerworks tended to lose a few in a matter of months - just those that were undetected defectives.  The springs don't care how heavy handed you are, they just work for so many cycles before they fail.  The best I've had were Swiss and looked to be gold plated.  If any surface defects are visible on replacements, they probably won't last as long as they should.

In case you have been paying someone to replace them, it isn't difficult to DIY but does take a while until you're used to it.  You need to uncouple all the springs (I use a small screwdriver to push them out of their location) then unscrew the action from the soundboard.  It's easiest to screw the action onto something like a chopping board so you don't bend anything then gently pull the pivot pin out as far as needed to reach the breakage.  Ideally you can slide a replacement in at the same time from the other end - it keeps all the components in place whilst you work.  Replace the spring and slide the rod back.  Screw the action back onto the soundboard and then hook all the springs back onto their levers (I have a small crotchet hook for this).

Rob.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner Pokerwork - treble button return springs
« Reply #2 on: February 07, 2015, 04:14:10 PM »

And take note that the springs for the inside row are not the same as for the outside row. Inside 0.5mm thick, outside row 0.55mm thick. The difference compensates for the different length of the levers.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Ebor_fiddler

  • Chris
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2340
  • Hohner 1040 C One-Row, Sandpiper D/G, Liliput C/F
    • Ebor Morris
Re: Hohner Pokerwork - treble button return springs
« Reply #3 on: February 08, 2015, 01:16:23 AM »

Pikey claims to work wonders with an elastic band and a clothes peg.  >:E
Logged
I'm a Yorkie!
My other melodeon's a fiddle, but one of my Hohners has six strings! I also play a very red Hawkins Bazaar in C and a generic Klingenthaler spoon bass in F.!! My other pets (played) are gobirons - Hohner Marine Band in C, Hohner Tremolo in D and a Chinese Thingy Tremolo in G.

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Hohner Pokerwork - treble button return springs
« Reply #4 on: February 08, 2015, 05:37:30 AM »

Pikey claims to work wonders with an elastic band and a clothes peg.  >:E
Apparently you can use them as temporary springs as well....... ;) >:E
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Hohner Pokerwork - treble button return springs
« Reply #5 on: February 08, 2015, 09:43:31 AM »

Dan Quinn used a Bic biro case on top of the grill as an anchor and elastic bands for springs. Temporary repair? ......I never knew his Pokerwork to be different.
  I agree with Rob, it doesn't matter how hard you hit the buttons, they have a limited amount of travel so you couldn't over stretch them. Basically it's metal fatigue. I have a machine at work for gold lettering. It uses a spring to lock down the brass type. It ran for over twenty years and then broke. On ordering another it broke within a week and another and another. Getting in touch with the makers in Germany the reply was "must have been a bad batch" we now carry a whole box of them. It's just the luck of the draw. Hope that puts your mind at rest.
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

baz parkes

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1894
    • All Blacked Up
Re: Hohner Pokerwork - treble button return springs
« Reply #6 on: February 08, 2015, 11:36:42 AM »

Pikey claims to work wonders with an elastic band and a clothes peg.  >:E

The late lamented Paul Havell used elastic bands and a biro or pencil...must have learned from Dan...and yes, one temporary repair lasted about 18 months..
Logged
On the edge of Cheshire's Golden Triangle, apparently...

george garside

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5401
Re: Hohner Pokerwork - treble button return springs
« Reply #7 on: February 08, 2015, 12:24:52 PM »

I can honestly say that in playing pokerworks and double ray (German veriety) for many years I have never had a broken spring but have had broken reeds occasionaly.

I wonder if it is anyting to do with not pressing the buttons  very far as so doing will not bend the springs as much resulting in less fatigue

george
Logged
author of DG tutor book "DG Melodeon a Crash Course for Beginners".

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Hohner Pokerwork - treble button return springs
« Reply #8 on: February 08, 2015, 12:29:53 PM »

No George, a spring will only travel the distance it was designed for, no matter how hard you hit it or for how long. I think it's just a case of metal fatigue.
 The cure?......... Play less tunes....  >:E
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

george garside

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5401
Re: Hohner Pokerwork - treble button return springs
« Reply #9 on: February 08, 2015, 12:36:47 PM »

but surely the further you press the button the further the spring will 'travel' or 'bend' and the more it travels or bends the more strain there will be on it resulting in earlier fatigue????

george
Logged
author of DG tutor book "DG Melodeon a Crash Course for Beginners".

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Hohner Pokerwork - treble button return springs
« Reply #10 on: February 08, 2015, 12:52:16 PM »

You may be right George, if you don't fully depress the button.  I would expect the initial movement to flex the straight elements of the spring before the coil starts to wind up in tension.  Every broken spring I've removed had one or other of the straight legs snapped off.  It suggest to me that the fault which promoted the failure is always at the bend into the coil - the point at which you go from flexing the wire to tensing the coiled section.  If the section of the wire is deformed at that point by a less than perfect tool, then a failure will occur much sooner.

Rob.
Logged

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Hohner Pokerwork - treble button return springs
« Reply #11 on: February 08, 2015, 01:30:17 PM »

The only 2915/2815 I've ever owned is the late 30s/early 40s C/F I play quite a lot at the moment, and that always performs impeccably (wish I could do the same!); however in my early melodeon days I owned a couple of new Ericas - this would be mid-70s for the first one, and mid 80s for the second, to replace the first one which was stolen - and both of those broke bass springs a couple of times, though never a treble. I've never had a Hohner reed break as far as I can recall.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Hohner Pokerwork - treble button return springs
« Reply #12 on: February 08, 2015, 01:33:35 PM »

but surely the further you press the button the further the spring will 'travel' or 'bend' and the more it travels or bends the more strain there will be on it resulting in earlier fatigue????

george

Ah but the travel is limited by the design of the box surely.
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

george garside

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5401
Re: Hohner Pokerwork - treble button return springs
« Reply #13 on: February 08, 2015, 03:27:38 PM »

I don't use anything like the available  travel

George (the light tapper!)
Logged
author of DG tutor book "DG Melodeon a Crash Course for Beginners".

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Hohner Pokerwork - treble button return springs
« Reply #14 on: February 08, 2015, 04:18:48 PM »

Collis Bird (the sledge hammer tapper)  ;)
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

steveh

  • Member
  • *
  • Offline Offline
  • Posts: 9
Re: Hohner Pokerwork - treble button return springs
« Reply #15 on: February 09, 2015, 04:00:18 PM »

Thanks to all for the helpful advice. I've now undertaken a temporary repair with an elastic band which actually works much better than I expected and should see me through a morris dance out tomorrow night.
I've ordered a full set of inner row springs and will fit these when they arrive. I must mention Mike Gott (another Melnet member) at this point - he has demonstrated excellent manual detrerity and replaced my last two broken springs. I'll be bribing him with some beer when the new spring set arrive.
Logged

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Hohner Pokerwork - treble button return springs
« Reply #16 on: February 09, 2015, 04:47:30 PM »

Once you have a box of springs you'll never ever have another break in your life !!  ;D
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Hohner Pokerwork - treble button return springs
« Reply #17 on: February 09, 2015, 11:54:33 PM »

Once you have a box of springs you'll never ever have another break in your life !!  ;D
Of course you will Nick - just not one which you could wrangle the spares into, to save your life  ;D

And as for selection boxes - when was the last time you found an O ring in one which actually fitted your precise need!

When S*d was formulating his famous law, rumour has it that he was having an optimistic day  :o
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Hohner Pokerwork - treble button return springs
« Reply #18 on: February 10, 2015, 12:19:59 PM »

That is so true Richard  :-\
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Mike Gott

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 285
  • Melodeon and hairy arm
Re: Hohner Pokerwork - treble button return springs
« Reply #19 on: February 12, 2015, 06:47:38 PM »

Groundhog Day. I have just fitted a new spring (again) to Steve's pokerwork. As with the last one it was on the inside (G) row. Accepting his incresing role as an instrument breaker on a par with Pete Townsend of The Who and one who expect to soon follow Jimi Hendrix's lead in burning his melodeon a la Monterey Pop, both breakages have ocurred on the notes that have been used most which would tend to point the finger at fatigue and sub-standard springs. Steveh now owes me a pint. Again.

Mike
Logged
"Traditional music was for entertainment, it wasn't for a further education class" (Bob Davenport)

Rivington Morris, Bolton, Lancashire.
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal