Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Attaching bass pallets  (Read 1865 times)

0 Members and 1 Guest are viewing this topic.

mr hohner

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 189
  • K.BLAND Melodeons
Attaching bass pallets
« on: February 12, 2015, 02:13:42 PM »

Hi all, I am in the process of restoring a 3 row 24 bass melodeon. I have sealed all the air leaks around the box but am having difficulty sealing the bass pallets, they keep falling off the rods that operate them. I have tried using glue gun glue but it hasn't worked, they just keep falling off. So, any suggestions of what glue I should use?

Regards
Mr hohner
Logged
Castagnari Studio D/G, Serenelli D/G, Hohner Pokerwork D/G, Castagnari Lilly D/G , Sandpiper Dublin II G/C, Serenelli Silyvia G/Acc

mr hohner

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 189
  • K.BLAND Melodeons
Re: Attaching bass pallets
« Reply #1 on: February 12, 2015, 02:15:43 PM »

Logged
Castagnari Studio D/G, Serenelli D/G, Hohner Pokerwork D/G, Castagnari Lilly D/G , Sandpiper Dublin II G/C, Serenelli Silyvia G/Acc

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Attaching bass pallets
« Reply #2 on: February 12, 2015, 02:57:31 PM »

Hot-melt glue should work fine for this job.

But are you attempting to use the leather/linen disks over the pallet arms in conjunction with the hot-melt glue?

If so, you would probably be better off not using the disks. Allow the spring tension hold the pallet arm end on to the pallet in the correct position, then apply a blob of hot-melt glue directly over the pallet arm end, overlapping a little on to the pallet surface. It should hold firmly, but if the glue is failing to adhere to the wooden pallet, it's possible the wood might be dirty or greasy. Similarly with the metal pallet arm end. Lightly roughen the wood surface and the pallet arm end with medium-grade sandpaper and try again.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Attaching bass pallets
« Reply #3 on: February 12, 2015, 04:41:07 PM »

Agree with Steve. Hot melt should be fine but I would add that little linen disk.
I'm not a box restorer but as a bookbinder (rtd just) I do know a little about glues. (:)
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Attaching bass pallets
« Reply #4 on: February 12, 2015, 04:48:27 PM »

Here is one I made earlier.

As Steve has mentioned all the surfaces should be clean and free from dust before you start to apply the glue.
« Last Edit: February 12, 2015, 04:50:23 PM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: Attaching bass pallets
« Reply #5 on: September 13, 2015, 08:39:53 AM »

I lost the high end G/A on my main box in play yesterday, with both notes then bleating annoyingly in time with anything I tried to play.

I perhaps stupidly tried waxing it back - that was all that was available. Yes, it quickly fell off again, but the spring does hold it in and it a matter of "never" using that button. Amazing how automatic that has become … as I discovered that even Bb tunes use a pull A ::)

Guess it's a matter of cleaning the wax out and buying a hot glue gun once it get home?
Logged
  _       _    _      _ 

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Attaching bass pallets
« Reply #6 on: September 13, 2015, 01:21:09 PM »

Guess it's a matter of cleaning the wax out and buying a hot glue gun once it get home?
Yes - the hot glue guns are not particularly expensive. I got mine from Homebase. It cost about £15 which included several spare glue sticks.

Cleaning the wax out is important. The hot glue will not adhere to a greasy or waxy surface. So physically scrape off all the wax you can with a blunt knife or similar, and then use a solvent such as acetone or nail varnish remover on cotton buds to remove all traces of wax. Be aware that some brands of nail varnish remover contain lanolin or similar oily conditioners (check the ingredients list). If so, you may need to go over the wooden surface of the pallet a couple more times with methylated spirit to remove the lanolin.

Similarly, clean the metal pallet arms free of wax too. Finally, roughen the wooden surface and the ends of the pallet arms slightly with sandpaper to give a 'key' for the glue to adhere to.

When using the hot glue gun, practice first on a piece of scrap card so you can learn how much pressure to apply to the glue gun trigger to give a neat blob that is not too big. See Theo's helpful photo in an earlier post. It can be also be a bit tricky manipulating the glue gun nozzle in between the pallet arms, so again an initial 'dry run' is a good idea. Have a thin spill of card handy to cover the tip of the nozzle and catch any rogue 'strings' of glue once you have deposited your glue blob.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: Attaching bass pallets
« Reply #7 on: September 14, 2015, 10:35:04 AM »

Thanks all. Isn't melnet good!
Logged
  _       _    _      _ 

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Attaching bass pallets
« Reply #8 on: September 14, 2015, 09:27:38 PM »

I have used a blob of Bostick non solvent glue (it's white when wet) together with a square of linen pressed down over where the arm slots into the back of the pallet. I've found that you can't always get the nozzle of the hot glue gun into confined spaces, and so tweezers plus the above works fine. I've just done this to the accidental row on a Hohner IV, because they are tucked away in a tricky to get at position. But the hot glue gun is much quicker and looks just like Theo's picture, if you can avoid the stringy bits (:)

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: Attaching bass pallets
« Reply #9 on: September 15, 2015, 07:00:46 AM »

Yes, it was a very tight thing. My pallet was at treble end, and there are 3 rows, much wire, cantelevers even! So I held it with tweezers "half in" while my "more practical" son Fred applied a worm of glue, and kept button down /lever up. Then we moved it into place smartly.

So 3½ hands in play. I think one could manage on 2 with practice and some sort of gig (cardboard strip)?

I haven't dared test it yet. Thanks to all for advice :Ph
Logged
  _       _    _      _ 
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal