Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Microvox meets 3v box!  (Read 5060 times)

0 Members and 1 Guest are viewing this topic.

Andy Next Tune

  • aka Andy Wooles
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1127
  • Melodeon with Accidentals? Make a PI Claim!!!
    • www.shavethedonkey.co.uk
Microvox meets 3v box!
« on: February 15, 2015, 07:50:07 PM »

I normally use microvox mics with our ceilidh band on my Binci.

However recently I've started using a 3V box (lovely Giustozzi from Rees) and when listening back to a few recordings, the low register voice is very dominant, and sounds almost 'buzzy'.

Is this a fact of life because the microvox mic is very close?

If so, I guess the answer is to switch to using a mic on a stand or look at the clip-on mics people have been discussing recently.

Definitely not my specialist area, so all input gratefully received.

Cheers, Andy



Logged
Andy, from the now ex-County Palatine of Cheshire

Caring for a European community of melodeons from France, Italy, Germany, Wales and Suffolk!

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Microvox meets 3v box!
« Reply #1 on: February 15, 2015, 08:01:02 PM »

I moved away from Microvox to

AKG C1000 I have the Mk111
and this mixer

With a cheapy Maplin tie clip mic for the bass.

sticky fingers

  • Tech Guru
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 119
Re: Microvox meets 3v box!
« Reply #2 on: February 16, 2015, 06:32:38 PM »

Hi Andy, I too would avoid using a microvox for your box, I used to have one years ago on my piano acc and found all sorts wrong with them, mine used to Velcro to the grill!, contact and bug mics generaly don't work well with free reed instruments as they output very high decibel levels which can overload the pickups in contact systems very easily, your better off with a couple of dynamic mics on stands at both ends, I too have a Giustozzi 3v with hand made bincis, custom made 6th button start and it is looouuud!. infact I have to move further away from the mic when I switch boxes!

by the way, the AKG lester suggests is a condenser mic and will either need a pp3 battery or 48volt phantom power from the desk to power the capsule, it's a very sensitive mic so will need carefull placement to avoid feedback and overload, this http://www.thomann.de/gb/the_tbone_sc_1000.htm is the same mic at about a third cost and also has an AKG capsule, now I don't want to diss lesters kit but the behringer 802 mixer has unbalanced main outs meaning it is prone to ground loops and mains hum, especialy when used near thrystor controlled lighting rigs, or in the worst case you might find the local taxi firm breaking through over your pa system in the middle of someones wedding ceilidh!, best wishes sf.

baz parkes

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1894
    • All Blacked Up
Re: Microvox meets 3v box!
« Reply #3 on: February 16, 2015, 10:25:41 PM »

, or in the worst case you might find the local taxi firm breaking through over your pa system in the middle of someones wedding ceilidh!, best wishes sf.

We used to do a gig in Stockport where we used to get the local priest doing mass...
Logged
On the edge of Cheshire's Golden Triangle, apparently...

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Microvox meets 3v box!
« Reply #4 on: February 16, 2015, 10:36:01 PM »

I get good enough results with SM57s on stands. Thoroughly robust mic, and doesn't need phantom power.
Sometimes I use a pair of T.Bone CC75 using heavy duty velcro on the back of the clip (because there's nothing on the melodoen to actually clip it to).

Recommend Soundcraft EPM8 if you're in the market for a mixer. XLRs with balanced out (impedance balanced, which is all you need for interference rejection), but your power amp had better have balanced input too. Most do.
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Cooper

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 705
  • Gaillrd G/C/#,Casta Allain8 GC,Lofft CF, giord ad
    • Cooper's homepage
Re: Microvox meets 3v box!
« Reply #5 on: February 17, 2015, 09:59:13 AM »

Hi Andy, I too would avoid using a microvox for your box,

I think it's strange you all find it lacking so much, i have used it intensively for a couple of years now, and i am still quite happy with the sound they reproduce on stage. What is wrong with it in all your opinions? (One ghostrider? I see hundreds!)
I have heared recordings back from me using those mics,...and i still feel they do a fine job for me,...Can it be something about the style i play? 

Could i see/hear some comparison somewhere?

W
Logged
Please correct my English, it's been a while, and i like to learn.
And don't be so polite! I know i must be typing tons of stuff that a native speaker would say differently...please enlighten me.

www.wouterkuyper.nl
www.lirio.nl
www.trekzakacademie.nl

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Microvox meets 3v box!
« Reply #6 on: February 17, 2015, 12:23:30 PM »

The Microvox M3xx range used capsules which distorted at high sound levels and didn't work with many melodeons.
The M4xx range use a different capsule with a higher SPL capability. I used to use them on my Oakwood, but after a lot of use I noticed I was getting distortion, especially noticeable as intermodulation products if I played a RH chord. Rather than replacing it risk ageing or deterioration again, I switched to a different system.

If it works for your instrument, Microvox kit used properly is a good and quite feedback-resistant system. I still have one built in to the bass end of my Oakwood, and use that sometimes, had no problems with it.
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Microvox meets 3v box!
« Reply #7 on: February 17, 2015, 03:22:45 PM »

by the way, the AKG lester suggests is a condenser mic and will either need a pp3 battery or 48volt phantom power from the desk to power the capsule, it's a very sensitive mic so will need carefull placement to avoid feedback and overload...

I started using a Microvox system and it was OK, but had a rather clipped response and didn't like me playing too loud.  I seem to remember that at the time Microvox gave a maximum input of 85dB before significant distortion kicked in.  As I was doing a fair bit of noise testing at work, I strapped the test kit onto the grille and found that with all three voices of my DB Morris 3 in I reached the critical volume level playing quite moderately.  Ther was much more scope for dynamics with only two voices.

I changed to a pair of AKG416 mini goosenecks, but they were not robust enough for a clumsy drunk like me and needed resoldering and glueing every outing.  Good sound though.  Now I use a pair of C1000s on drum stands wich can pack down small enough for sitting position without the boom disembowling passing dancers.  They are indeed sensitive, although being cardioid I don't find feedback a problem.  If it were to prove so I would clip on the hypercardioid adapter.  Unfortunately if I forget to switch off between numbers, the audience can hear anything whispered on stage.

Rob.
Logged

Cooper

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 705
  • Gaillrd G/C/#,Casta Allain8 GC,Lofft CF, giord ad
    • Cooper's homepage
Re: Microvox meets 3v box!
« Reply #8 on: February 18, 2015, 09:32:33 AM »

The Microvox M3xx range used capsules which distorted at high sound levels and didn't work with many melodeons.
The M4xx range use a different capsule with a higher SPL capability. I used to use them on my Oakwood, but after a lot of use I noticed I was getting distortion, especially noticeable as intermodulation products if I played a RH chord. Rather than replacing it risk ageing or deterioration again, I switched to a different system.

If it works for your instrument, Microvox kit used properly is a good and quite feedback-resistant system. I still have one built in to the bass end of my Oakwood, and use that sometimes, had no problems with it.

I feel like a complete idiot,...i have no idea what you are talking about :-) What does SPL-capacity mean? And intermodulation products?

Do i gather correctly that you say that when played softly there is no problem, but that you get distortion once you start to hit RH-chords? (i.e. more volume going in the mic?).

I started using a Microvox system and it was OK, but had a rather clipped response and didn't like me playing too loud.  I seem to remember that at the time Microvox gave a maximum input of 85dB before significant distortion kicked in.  As I was doing a fair bit of noise testing at work, I strapped the test kit onto the grille and found that with all three voices of my DB Morris 3 in I reached the critical volume level playing quite moderately.  Ther was much more scope for dynamics with only two voices.


That's basically the same thing as Anahata said, right? I should test that out. Perhaps i dont have that problem because i dont play 3V-boxes on stage. (who needs the volume, if you can just ask the soundguy for more volume)
W
Logged
Please correct my English, it's been a while, and i like to learn.
And don't be so polite! I know i must be typing tons of stuff that a native speaker would say differently...please enlighten me.

www.wouterkuyper.nl
www.lirio.nl
www.trekzakacademie.nl

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Microvox meets 3v box!
« Reply #9 on: February 18, 2015, 12:10:21 PM »

I feel like a complete idiot,...i have no idea what you are talking about :-) What does SPL-capacity mean? And intermodulation products?
Sorry! SPL = Sound Pressure Level.
There's a maximum sound level above which a microphone starts distorting, and it's different for each type of mic.

Intermodulation: you play two notes, but you hear four. (and the extra tones aren't musical)

Quote
Do i gather correctly that you say that when played softly there is no problem, but that you get distortion once you start to hit RH-chords? (i.e. more volume going in the mic?).

Yes, that's exactly what I meant. Thank you for translating into plain English  :|bl
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Andy Next Tune

  • aka Andy Wooles
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1127
  • Melodeon with Accidentals? Make a PI Claim!!!
    • www.shavethedonkey.co.uk
Re: Microvox meets 3v box!
« Reply #10 on: February 20, 2015, 12:10:49 PM »

Finally had a chance to hook things up again, try different thingd, record the output and then listen. Repeat then repeat. Draw conclusions.

Definitely sounds like the Guistozzi is over-powering the Microvox (M4xx) in 3V, as most have predicted. And its much better behaved with the low reed out.

BTW - the reason for using the 3V is not volume, but the extra layer of sound the low voice adds to the mix.

So I think time will now be spent on the Thomann site, the CC75s are certainly attractively priced. I will probably look for alternative phantom power source to our band mixer amp as well. Any mini mixer recommendations apart from Lester's?

Thanks for all the input.

Andy
Logged
Andy, from the now ex-County Palatine of Cheshire

Caring for a European community of melodeons from France, Italy, Germany, Wales and Suffolk!

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Microvox meets 3v box!
« Reply #11 on: February 20, 2015, 01:16:08 PM »

Any mini mixer recommendations apart from Lester's?

I mentioned earlier: Recommend Soundcraft EPM8 if you're in the market for a mixer.
If you don't need that many channels there's the EPM6 with only 6 mic inputs, otherwise looks identical.

Also available from http://thomann.de. Check prices including shipping for best value. Thomann, despite being in Germany, are very competitive in price and deliver in a few days.
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

sticky fingers

  • Tech Guru
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 119
Re: Microvox meets 3v box!
« Reply #12 on: February 20, 2015, 06:19:10 PM »

Like Anahata, I currently use a soundcraft, the smaller EPM6, built in power supply, (no wall wart),inserts on everything for compressors or graphic eq, mid sweep on the 3 band eq for taming mid frequency resonances, there are also good little desks from PHONIC, YAMAHA, ALLEN & HEATH and SAMSON, it just depends on the facilities you need and the amount of compromises you can work around!, just make sure it has balanced outputs!, best wishes sf.

penn

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 574
Re: Microvox meets 3v box!
« Reply #13 on: February 20, 2015, 06:36:47 PM »

Any mini mixer recommendations apart from Lester's?
I recently bought an Alto live desk (1604 - I don't think that's what you're looking for tho') and am very impressed with quality, ruggedness, sound and features. I use a cheapish Allen and Heath too but I think the Alto is better quality.
http://www.altoproaudio.com/series/alto-mixers
They do quite a range, and I would consider them for a job like this. I was keen to avoid Behringer - when buying the Alto I did a poll of colleagues and contacts and everyone has Behringer break-down stories.
Steve
Logged
Hohners, Dino Baffetti, Lilly, Benny + a lot of junk.

Bill Young

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1151
  • Paolo Soprani BCC#
Re: Microvox meets 3v box!
« Reply #14 on: February 21, 2015, 09:07:43 AM »

. . . and everyone has Behringer break-down stories.


I don't. I've used a Behringer Xenyx 1202FX mixer for our group's gigs for several years now without any problems (currently into a Bose L2 Compact PA). Several other Behringer products in my experience have also performed well without problems - mics, a keyboard amp, a smaller 802 mixer and a PMP960M power amp/mixer. I think Behringer products are generally good quality and good value.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Microvox meets 3v box!
« Reply #15 on: February 21, 2015, 09:28:08 AM »

Behringer kit is great as long as it keeps working.  I had a Berhinger mixer that was fine for several years, then failed spectacularly during a gig, with a loud bang, a blue flash and a puff of smoke!!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Bill Young

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1151
  • Paolo Soprani BCC#
Re: Microvox meets 3v box!
« Reply #16 on: February 21, 2015, 12:29:58 PM »

Behringer kit is great as long as it keeps working.  I had a Berhinger mixer that was fine for several years, then failed spectacularly during a gig, with a loud bang, a blue flash and a puff of smoke!!

Now I'm scared! What to add to the kit - a spare mixer or a fire extinguisher?
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal