Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3   Go Down

Author Topic: 3rds switch stuck (treble side)  (Read 7068 times)

0 Members and 1 Guest are viewing this topic.

Red

  • Member
  • *
  • Offline Offline
  • Posts: 30
3rds switch stuck (treble side)
« on: February 16, 2015, 01:50:19 AM »

I have a Giustozzi box that was shipped from a lot dryer place than mine. I've been playing it delicately making sure it gets used to the new climate. When I finished my session yesterday I had the thirds switch pushed in, today when I went to play, I pulled it up and it didn't budge. I gave it another pull and no luck. When I got it, it was a fairly tight push and pull to begin with. I havent really used it due to the fear of something like this happening.

I'm curious as to if the difference in climate has warped something or is making it impossible to pull up. Im not gonna take it apart just yet. I want to see if anyone has had a similar issue and what you all have done to fix it. I don't think the whole mechanism could be too complicated, I just don't want to go and rip the box apart and make something worse.

Just like a hohner, I'm assuming I just pull the pins out around the box and it comes apart?
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: 3rds switch stuck (treble side)
« Reply #1 on: February 16, 2015, 10:32:33 AM »

The register slide for the third switch is clamped under the chord reed block.
It should free up if you simply slacken off the screw holding the end of the reed block in place.

Pull the pins out, just like a Hohner.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: 3rds switch stuck (treble side)
« Reply #2 on: February 16, 2015, 10:37:49 AM »

Pull the pins out, just like a Hohner.
But take care not to muddle them. Quite often, Italian bellows pins are slightly different diameters, even on the same instrument. They need to be replaced back in the same holes.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

bb23

  • Good talker
  • **
  • Offline Offline
  • Posts: 53
Re: 3rds switch stuck (treble side)
« Reply #3 on: February 16, 2015, 01:33:58 PM »

Mike,
It's not clear which switch you're referring to from your title. The 3rds switch is on the bass side. Either way, both switches were always snug, but have never been full on stuck (when I had it).

The 2 previous posters know infinitely more than I about every aspect of melodeons. However, when I got a concertina from Wim Wakker, he had very good advice, which boiled down to not being in a hurry to muck around with anything for awhile (like a couple of weeks). He suggested playing freely, but with a Yoda-like patience for mechanical things after a major climate change. There are no switches on a concertina, but I think the overall concept applies.

My inclination would simply be to pull on the switch several times per day for a couple of days and see how that goes. Most likely, it will resume its normal behavior (snug but fully functional) without need to take it apart.
Brandon
Logged
Brandon

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: 3rds switch stuck (treble side)
« Reply #4 on: February 16, 2015, 02:54:16 PM »

I had trouble with a one row slides ( switches) on a harmona box I had, I found that keeping it in the case with a moisture pack did the trick. I didn't like doing it because made playing it more of a hassle.
I've had no problems with My Beltuna (Brandon sold to Me, thanks) it has metal slides (:)
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: 3rds switch stuck (treble side)
« Reply #5 on: February 16, 2015, 03:38:17 PM »

Another possibility is that a valve has dropped off on of the reeds on the inside and has become lodged on the slide.  Not very likely but worth bearing in mind.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Red

  • Member
  • *
  • Offline Offline
  • Posts: 30
Re: 3rds switch stuck (treble side)
« Reply #6 on: February 16, 2015, 06:14:04 PM »

I'm gonna let it sit for a couple days and see if that does anything.  If nothing changes, i will throw a moisture pack in there and see what's up. It doesnt wanna budge at all. Theres not even a little give to it the last time i checked which is now almost 24 hours ago.

Sorry. I really don't know much terminology/ practically anything... It's kinda.. bad... I dunno  ;D  :||:


Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: 3rds switch stuck (treble side)
« Reply #7 on: February 16, 2015, 06:59:26 PM »

I'm gonna let it sit for a couple days and see if that does anything.  If nothing changes, i will throw a moisture pack in there and see what's up. It doesnt wanna budge at all. Theres not even a little give to it the last time i checked which is now almost 24 hours ago.

Sorry. I really don't know much terminology/ practically anything... It's kinda.. bad... I dunno  ;D  :||:
If it's that bad, I think you really ought to pull the bass-end bellows pins and look inside.

The slider which controls the thirds in the chords is a thin blade-like strip made of thin metal sheet or, less likely, very thin plywood. The slider has a series of holes corresponding the the openings on the thirds reed block chambers. In the 'thirds in' position, the holes line up, in the 'thirds out' position, the slider holes are shifted out of alignment with the reed chamber openings, thus preventing air reaching the reeds.

The slider blade will run in a shallow channel, either on the underside of the reed block, or else in the base board which the reed blocks are mounted on. The top end of the slider blade will probably be glued to a small wooden block (SWB) into which the metal shaft of the mushroom stop is screwed.

The most likely reasons for the slider to become stuck are:
1. The shaft of the mushroom stop is too tight a fit through the wooden casing of the instrument. If it was previously OK then an excessive change in humidity could cause stiffness.
2. The SWB has got jammed against the base board because of dust/debris/swelling due to excessive changes in humidity.
3. The slider blade has become too tightly clamped by the reed block (see Rees's earlier comment). An excessive change in humidity could cause this.
3. The slider blade has become jammed in its channel somehow.
4. The slider blade has broken.
5. If the mushroom stop has become screwed in too far, the SWB will become pulled up tight against the inside of the wooden casing and will no longer function. There is an optimum setting for the slider travel governed by just how much the metal stop shaft is screwed in.
6. If the slider stop has had a bit of a sideways knock, the shaft can become slightly bent. This can cause stiffness in the operation of the stop.

Once you have opened up the box, the way in which the slider works should become obvious, and anything amiss will hopefully become apparent... You will need to remove the chords reedblock to see the slider fully. To remove the reed block, loosen the clamp screws at each end and lift the reed block out carefully, taking care not to catch any of the delicate valves ('leathers') in the process.

When re-fixing the reedblock, ensure that the slider is located in the shallow channel before gently tightening down the clamps. The reed block should be snugly clasped so that it doesn't shift about, but don't overtighten the clamp screws.

Don't be tempted to use any form of liquid lubrication anywhere, ever. No oil, no WD40, silicone, etc. The only permissible lubricant is finely powdered graphite such as locksmiths use.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: 3rds switch stuck (treble side)
« Reply #8 on: February 16, 2015, 07:34:28 PM »

I'd put the moisture pack in and wait a couple of days if it works then you know it was humidity.
It won't hurt anything and if not then try what others have suggested.
good luck!
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: 3rds switch stuck (treble side)
« Reply #9 on: February 16, 2015, 11:36:04 PM »

I'd put the moisture pack in and wait a couple of days if it works then you know it was humidity.
It won't hurt anything and if not then try what others have suggested.
good luck!
I'd suggest doing it the other way round. It is a matter of a few minutes to just open up the box to see what's what.
Then if there is nothing obvious, it might be worth doing the moisture pack thing, but from the OP's description it sounds as if there is something definitely wrong which should be revealed by an internal inspection.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: 3rds switch stuck (treble side)
« Reply #10 on: February 17, 2015, 12:02:26 AM »

sounded like the op was going to let it sit for a couple days anyway, so why not throw packs in while waiting? where there's no risk of damaging anything.
some folks aren't comfortable with taking things apart and I know a few that should not even try.
I not speaking of anyone here or the op.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: 3rds switch stuck (treble side)
« Reply #11 on: February 17, 2015, 10:42:15 AM »

I can't see any useful purpose to putting moisture packs into the case.  If it has been moved between areas with widely different humidity which has caused a problem then it needs a few weeks (not days) to adjust to the new conditions.  Adding a moisture pack is just adding another variable to the situation.
Having said that I doubt that it is environmental changes at the root of this problem.  If it was I would expect a gradual change with the stop getting stiffer over time, not just locking up completely. 
I agree with Steve that someone needs to take a look inside. But it can't do any harm to wait a few weeks for the timber to aclimatise.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

bb23

  • Good talker
  • **
  • Offline Offline
  • Posts: 53
Re: 3rds switch stuck (treble side)
« Reply #12 on: February 17, 2015, 11:26:14 AM »

 I won't try to add any additional advice here and don't think this will change the advice above...

Just a note that the slide Mike is struggling with is the treble slide that operates one of the middle reed blocks. After my last post, I recalled that the 3rds switch on the bass side of this box is a simple switch.
Logged
Brandon

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: 3rds switch stuck (treble side)
« Reply #13 on: February 17, 2015, 12:08:09 PM »

I won't try to add any additional advice here and don't think this will change the advice above...

Just a note that the slide Mike is struggling with is the treble slide that operates one of the middle reed blocks. After my last post, I recalled that the 3rds switch on the bass side of this box is a simple switch.
OK - if it is the stop which controls the right-hand side low octave voice, the stop/slider mechanism will be very similar to what I have described previously. Definitely worth opening up the box to see what is amiss.

I agree with Theo that any environmental changes will probably take effect gradually. Almost certainly this is something else and needs to be investigated. Waiting around is unlikely to solve the problem.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Red

  • Member
  • *
  • Offline Offline
  • Posts: 30
Re: 3rds switch stuck (treble side)
« Reply #14 on: February 17, 2015, 03:42:19 PM »

So I decided to open it up. Right now I'm looking at the 3 reed blocks. I touch the switch, the 2nd one moves. If I lightly push it up and down the entire reed block moves. Now, I have all the screws undone and am ready to remove the reed block. When I pull it out, the switch moves with it. I have not pulled it out all the way yet.

If I screw the block back in place and give the switch a pull, there's a small wooden block located below the switch on the side where the innards are. When I pull, that block moves up and down and is making a bendy wood noise. I am not taking out the reed block in fear of the slide being stuck on the reed block itself or something. I can provide a video If necessary.
Logged

Red

  • Member
  • *
  • Offline Offline
  • Posts: 30
Re: 3rds switch stuck (treble side)
« Reply #15 on: February 17, 2015, 03:51:32 PM »

on the right side of the reed block I can also see the slide sticking out. It seems like I cant pull the reed block all the way out because the bit that's sticking out will get stuck on the piece of wood that the fasteners are attached to to hold all the blocks in place.
« Last Edit: February 17, 2015, 03:57:03 PM by Red Strange »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: 3rds switch stuck (treble side)
« Reply #16 on: February 17, 2015, 04:01:52 PM »

The reed block should not move at all when the switch is operated.  The only movement you might see is the small block of wood which the stop screws into which should move along with the stop.

I'm afraid that the centre reed block might have been damaged I transit. Or at the very least the fastenings have been disturbed on some way.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Red

  • Member
  • *
  • Offline Offline
  • Posts: 30
Re: 3rds switch stuck (treble side)
« Reply #17 on: February 17, 2015, 04:07:11 PM »

The block wants to move, but it's not going anywhere. Does the whole mechanism usually move with the reed block when you take it out?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: 3rds switch stuck (treble side)
« Reply #18 on: February 17, 2015, 04:37:32 PM »

Probably best if you could post photos.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Red

  • Member
  • *
  • Offline Offline
  • Posts: 30
Re: 3rds switch stuck (treble side)
« Reply #19 on: February 17, 2015, 05:07:55 PM »

Bottom of the reed block where the bit is sticking out
http://imageshack.com/a/img905/9264/ptqKZo.jpg
http://imageshack.com/a/img673/17/HgWCdz.jpg
Whenever i lift the reed block up to pull it out, this will be in the way.



Top of the reed block where that small wooden piece is located
http://imageshack.com/a/img673/3866/glTztf.jpg
http://imageshack.com/a/img673/500/Bf1Br7.jpg
When I pull the switch when everything is unscrewed, the whole entire reed block moves
When I pull the switch when everything is screwed in, the small wooden piece moves, but very little. It squeaks like its rubbing something or is bending. It seems like its lifting up on the side closest to me/ the camera, but the other side is stuck. Are there screws that are fastening the metal slide in place to that block? Could those be stuck/ jammed against the wood somehow?

Even if the bit wasn't sticking out on the end, the entire switch and mechanism moves with the reed block when i move it, so the knob would prevent me from taking it all the way out.

« Last Edit: February 17, 2015, 05:11:53 PM by Red Strange »
Logged
Pages: [1] 2 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal