Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2] 3   Go Down

Author Topic: 3rds switch stuck (treble side)  (Read 7087 times)

0 Members and 1 Guest are viewing this topic.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: 3rds switch stuck (treble side)
« Reply #20 on: February 17, 2015, 05:18:11 PM »

I'm assuming you have slackened the screw at the bottom of the reedblock, and removed the plate at the top of the reedblock?  They should be the same as on the two blocks on either side.

Apart from the fasteners not being in place everything looks ok.  You should now be able to lift out the middle reed block and the register slide should remain in place where the block has been sittting on it.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Red

  • Member
  • *
  • Offline Offline
  • Posts: 30
Re: 3rds switch stuck (treble side)
« Reply #21 on: February 17, 2015, 05:23:14 PM »

I have removed everything. The reed block is ready to come out, but when I move the reed block the slide and the switch move with it. When I pull the bottom end up, the little piece of metal sticking out gets caught on the rim of the box. Unless the knob on the outside of the accordion unscrews, I don't see it coming out.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: 3rds switch stuck (treble side)
« Reply #22 on: February 17, 2015, 05:29:32 PM »

The knob on the outside can be unscrewed. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Red

  • Member
  • *
  • Offline Offline
  • Posts: 30
Re: 3rds switch stuck (treble side)
« Reply #23 on: February 17, 2015, 05:46:43 PM »

ohh....wow. Just took more effort than i thought...

well im looking at it now... it seems okay, but if i pull on that block, it doesnt move at all. The bottom of the slide is off the track. It springs up and down... I have now removed that wooden block and have tugged on the metal slide. Nothing. I could imagine somewhere in the middle of the track is has warped causing it to pinch? Should i just go ahead and take out the metal slide even though i may not be able to get it back in?
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: 3rds switch stuck (treble side)
« Reply #24 on: February 17, 2015, 06:00:49 PM »

From what you are describing, it seems as if the metal slider blade is sticking to the reed block for some reason. It shouldn't do this; you should be able to lift out the reed block and leave the metal slider behind.

Try to find out where the slider blade is sticking and if you can, very gently ease the slider blade away from the reed block. You might need to poke it with a blunt thing or ease something between the slider and the reed block. If you can get it free, the reed block should lift clear and you can investigate why the sticking occurred. Go carefully so as not to put a kink or crease in the slider blade.

Good luck!
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: 3rds switch stuck (treble side)
« Reply #25 on: February 17, 2015, 06:05:13 PM »

Also, remove the other two reed blocks and put them safely to one side, so you have room to work on the centre reed block and slider.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: 3rds switch stuck (treble side)
« Reply #26 on: February 17, 2015, 06:07:52 PM »

The wooden block that the stop screws into should be attached to the metal slide.  The slide itself should lift out easily, so whatever is holding it is the cause of the problem.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Red

  • Member
  • *
  • Offline Offline
  • Posts: 30
Re: 3rds switch stuck (treble side)
« Reply #27 on: February 17, 2015, 06:15:44 PM »

it seems as it is getting stuck in the middle. I have removed the slide from the block. I put it back in the top and when i slide it down, it gets stuck about half way. There is no residue or anything noticeable on the reed block. I'm guessing the track has warped... I'm not sure if I'll be able to get the slide back in. 
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: 3rds switch stuck (treble side)
« Reply #28 on: February 17, 2015, 06:19:28 PM »

One further question:  is the slide located in a completely enclosed slot along the length if the reed block, or does it sit in a shallow channel in the underside off the reedblock so the the enclosed slot is made by the reed block on one side and the sound board beneath it?
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Red

  • Member
  • *
  • Offline Offline
  • Posts: 30
Re: 3rds switch stuck (treble side)
« Reply #29 on: February 17, 2015, 06:24:20 PM »

Not quite gettin' ya there... if you mean if the slides track has been made into the reed block, then no, the track is a separate piece of wood, but two small rails along the side. Nothing else.
Logged

Red

  • Member
  • *
  • Offline Offline
  • Posts: 30
Re: 3rds switch stuck (treble side)
« Reply #30 on: February 17, 2015, 06:28:49 PM »

By leaving it in, I'd think that eventually over time, from the pressure the rails will correct themselves from the pressure from the slide?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: 3rds switch stuck (treble side)
« Reply #31 on: February 17, 2015, 06:46:34 PM »

Seems to be a less common construction. Can you post photo?
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Red

  • Member
  • *
  • Offline Offline
  • Posts: 30
Re: 3rds switch stuck (treble side)
« Reply #32 on: February 17, 2015, 06:53:54 PM »

Logged

Red

  • Member
  • *
  • Offline Offline
  • Posts: 30
Re: 3rds switch stuck (treble side)
« Reply #33 on: February 17, 2015, 06:59:25 PM »

I have put everything back and have removed the switch. That end of the slide is no longer sticking up. Everything is flesh with the rail and looks okay. I think I am gonna wait for a while and just not touch it and see what happens. If it doesn't fix itself then the only thing my amateur brain can think of is using a very low grain sand paper and working it along the edges of that rail where there seems to be resistance, but I'm gonna wait to do anything like that last, or unless there are other solutions that are posted here. At least it doesn't look like it's beyond repair.

With anything musical that I partake in I do end up having bad luck. Life is extremely weird.
« Last Edit: February 17, 2015, 07:02:52 PM by Red Strange »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: 3rds switch stuck (treble side)
« Reply #34 on: February 17, 2015, 07:10:13 PM »

There surfaces of the slide should all be completely smooth.  If you can feel any rough spots these may be causing the slide to get stuck. If you use a fine abrasive paper place the paper on a flat smooth surface and gently rub the slide on it.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: 3rds switch stuck (treble side)
« Reply #35 on: February 17, 2015, 09:03:33 PM »

 I was wrong as usual about the packs. :(
Does look like the slide sits in a dado or slot in the bottom of reed block and if you line up the holes it should move (slide) back and forth the distance of the hole with out to much resistance. My guess is it may need a little resistance to keep the stop from sliding out of alignment when playing if thats what holds it in place. might be worth sanding edges of rail a little if it does not correct itself.  It could be tricky to sand edge and not sanding face where holes are, which could effect the air tightness? I think? or maybe you could just sand the edge of metal slide?
In your picture of the metal slide, the bottom of the slide looks as if it has scratches? may not be the trouble if it is sticking as you say with reed block out of the box.
I'm sure others will be along shortly to convince me to stop giving advise. ;D
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Red

  • Member
  • *
  • Offline Offline
  • Posts: 30
Re: 3rds switch stuck (treble side)
« Reply #36 on: February 17, 2015, 10:31:48 PM »

I was thinking of sanding down the slide, but I'm gonna wait until the box is completely acclimated to my part of the states before I do anything to it. I don't want to fix it now, but end up running into the problem of it falling out after it has been acclimated because the rails shifted again. it's not even noticable so I'm hoping I'm lucky and it fixes itself.
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: 3rds switch stuck (treble side)
« Reply #37 on: February 18, 2015, 12:55:57 AM »

I was thinking of sanding down the slide, but I'm gonna wait until the box is completely acclimated to my part of the states before I do anything to it. I don't want to fix it now, but end up running into the problem of it falling out after it has been acclimated because the rails shifted again. it's not even noticable so I'm hoping I'm lucky and it fixes itself.

Well done for getting all this way!

I think you are being little over-cautious though. Try the following:

1. Check that there are no rough edges or faces on both the metal slider and the wooden face and rails sides on the reed block.
2. Note exactly where the slider is/was binding in the channel and try very gently sanding the vertical sides of the rails at that point. To sand, a useful tool is a very fine carborundum 'emery' board such as manicurists use. Its stiffness will enable you to sand the vertical faces of the rails without rounding off any corners. Go very gently, using minimum pressure and keep checking the movement of the slider in the channel. Carefully brush away any wood dust, trying as much as possible to keep it out of the reed chambers.
3. Once the slider is moving freely but still a snug fit in the channel, move it in and out by hand a few times to burnish the wood. Beware of over-sanding - you don't want the slider to become a sloppy fit!  :o
4. Rub a small quantity of locksmiths' graphite powder on to the channel surfaces and repeat the burnishing action with the slider. If you can't get  graphite powder, rub a very soft (2B or softer) drawing pencil on the slider and the channel base/sides and burnish again.

All this should have freed up the slider, so try reassembling everything carefully. The amount of tightening on the reed block clamps will partly govern how readily the slider ultimately moves. Screw the clamps down too far and the slider will be too stiff and vice versa.

When you get to the stage of screwing the mushroom stop back into position, you need to get the depth of the threaded portion in the small wooden block just right so that the travel on the stop will open and close the air holes fully. If you screw in the mushroom stop too far, or not enough, the air holes will not line up properly, neither fully opening nor fully closing.

Put it all back together and test everything, including play testing. Hopefully you will have a fully functioning box!  (:)



« Last Edit: February 18, 2015, 12:57:51 AM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

bb23

  • Good talker
  • **
  • Offline Offline
  • Posts: 53
Re: 3rds switch stuck (treble side)
« Reply #38 on: February 18, 2015, 03:56:28 AM »

I used to a boss who, despite his many shortcomings, had a saying that I have found to be quite useful at times:

"Don't just do something, Stand there!"

My knowledge of the background of this situation gives me pause about the notion of sanding anything just yet...Just 10 days ago, I made the Youtube video meant to help me sell this box. At 1:40--1:44, one can see just how easily the treble stop was operating at that time (and always had). Now, the instrument has barely completed its 2000 mile journey from a brown spot on the map to a green spot on the map. Excellent technical advice to be had here, but waiting a week won't hurt anything or anyone....sanding can always be done later; un-sanding however...now that sounds complicated.

For reference only, not vanity:
https://www.youtube.com/watch?v=meB4gKOD6BQ
 :||:
Logged
Brandon

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: 3rds switch stuck (treble side)
« Reply #39 on: February 18, 2015, 09:23:57 AM »

Thanks for that link Brandon. Yes - it's clear that the treble end stop was operating properly at that time.
So we have to ask the question - what can have happened in the meantime?

As Theo speculated in an earlier post, it's possible that there was some shock or damage during the transit process somehow which could have caused the reed blocks to shift a fraction and allow the slider to jump out of its proper channel. Trying to subsequently operate the slider whilst in its mis-aligned state could have caused some slight damage to the channel slot/rails, or slight bending to the slider blade.

Or, that the change in environmental conditions in its new home has caused some swelling of the wood in the slider channel so that it is gripping the slider more tightly. But I cannot believe that purely environmental changes can have had such a sudden and drastic negative effect. Your home conditions and the OP's conditions are not going to be that different. If the OP was living in a tent in a rain forest, I could perhaps believe it.

I do understand your caution about about sanding and not being able to reverse the process. But we have to take the situation as it now is. If there is a sticking point in the channel somewhere for whatever reason, that has to be dealt with.

Here's my advice for the moment:

1. With everything disassembled e.g. as in the latest set of photos, try manually moving the slider to and fro in the slider channel. If it seems to move freely, then carefully reassemble the instrument, ensuring that all the components go back to their proper positions, testing the proper movement at every stage. When putting the reed blocks back in place, check that the slider is still housed in its proper channel location - it can be a bit fiddly to locate it properly. Ensure the reed blocks are snuggly held down by the clamps - there should be no movement, but not overtightened so as to risk distorting anything or stripping the threads in the wood.

Then - if the instrument works as it should, great! No need for further action.

However....

2. If, in the disassembled state, the slider does not move freely in its channel then clearly something has to be done, and this is where identifying any sticking point and careful easing (by sanding, burnishing, etc.) is appropriate. By 'sanding' I mean a very light, gentle action, almost imperceptibly removing material - almost polishing rather than abrading. Waiting for Godot or the melodeon fairies to do it for you is probably not going to be effective. The aim has got to be free movement of the slider in the channel, without any sloppiness. Once this is achieved, you can go to stage 1 again.

As always, go carefully. Make minute changes only and test, test, test, at each stage. Good luck!
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk
Pages: 1 [2] 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal