Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 [3]   Go Down

Author Topic: 3rds switch stuck (treble side)  (Read 7060 times)

0 Members and 1 Guest are viewing this topic.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: 3rds switch stuck (treble side)
« Reply #40 on: February 18, 2015, 10:21:35 AM »

The screws that hold the reed block with a register beneath must be adjusted carefully.  Just  a bit too much tightening of either screw can jam the slide. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: 3rds switch stuck (treble side)
« Reply #41 on: February 18, 2015, 10:46:47 AM »

Steve / Theo (Other fettlers opinions may be available ;))

While I am a great fan of Graphite, its use via 'puffed' application in wood still makes me cringe a bit.

As it is probably more easily available to the amateur box wrangler and less obviously messy if overdosed, would you gents consider talcum powder / French chalk a reasonable substitute dry lubricant in perhaps less skilled hands?

 
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: 3rds switch stuck (treble side)
« Reply #42 on: February 18, 2015, 10:54:06 AM »

Gtaphite is not really necessary in this application if the original source of the problem is dealt with.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

bb23

  • Good talker
  • **
  • Offline Offline
  • Posts: 53
Re: 3rds switch stuck (treble side)
« Reply #43 on: February 18, 2015, 11:44:20 AM »

Steve, excellent points all....as one of the least knowledgeable folks in this room, I will step aside.

p.s. Godot was clearly out to lunch, but melodeon fairies? Their existence has yet to be proven or disproven, so I often give them the benefit of the doubt. (:)
Logged
Brandon

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: 3rds switch stuck (treble side)
« Reply #44 on: February 18, 2015, 06:10:35 PM »

While I am a great fan of Graphite, its use via 'puffed' application in wood still makes me cringe a bit.

As it is probably more easily available to the amateur box wrangler and less obviously messy if overdosed, would you gents consider talcum powder / French chalk a reasonable substitute dry lubricant in perhaps less skilled hands?
French chalk is supposed to be pure mineral talc, and it might be OK, but talcum powder, baby powder etc., I believe can have other stuff added too (gypsum, calcium carbonate?) as well as fragrance.

When I use graphite as a lubricant I usually mix a small quantity of the powder with a little methylated spirit or acetone. I apply the mixture with a small artists' paint brush. The solvent carries the graphite powder into the place where it's needed and then evaporates, leaving the graphite behind. I try to avoid 'puffing' the graphite as I agree, it tends to go everywhere.  ::)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Red

  • Member
  • *
  • Offline Offline
  • Posts: 30
Re: 3rds switch stuck (treble side)
« Reply #45 on: February 18, 2015, 07:41:44 PM »

I'm gonna wait for some fairies. As eager as I am to fix it, I'm not taking any chances. As posted earlier, someone had this same problem with a box shipped from Brandon and it ended up correcting itself. Everything was working when I had received it and then over the course of two days it seized up. Being im inexperienced and this is my first occasion of actually peeking inside a box, im not gonna push It. Worse comes to worst, the mechanism doesn't look too complicated to recreate and I could probably do so. I'll give it some thought. I may not even mess with the rails at all. The slide seems a lot easier to create If I screw up. There's a lot of advice here and I'm quite thankful this place exists.
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: 3rds switch stuck (treble side)
« Reply #46 on: February 18, 2015, 09:03:16 PM »

Hi Red,
The Beltuna box I bought from Brandon was perfect and I never had any problem with the slide on that box and was playing it right away.
I never had to wait for it to acclimate or any other box I bought. It did develop a sticky Lever on button 6 but I reamed it out as it was sticking on the axle, this only happen months later when the summer came around and humidity was high. It works fine now.

The box I had trouble with was a harmona and again it only happen a while after I got it during the summer. It was in the key of C and I learned  later that I needed a box in D so I traded it in for my silvetta in D. and I did not buy it from Brandon just to clear that up.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D
Pages: 1 2 [3]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal