Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Taping thirds on a pokerwork  (Read 3784 times)

0 Members and 1 Guest are viewing this topic.

Andy Next Tune

  • aka Andy Wooles
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1127
  • Melodeon with Accidentals? Make a PI Claim!!!
    • www.shavethedonkey.co.uk
Taping thirds on a pokerwork
« on: March 08, 2015, 07:12:29 PM »

A friend has asked for assistance in blocking off the thirds on their Pokerwork.
Is this likely to be a straight-forward task of identify the reed and apply 'suitable' tape or are there gremlins hiding to bite the unwary?

thanks, Andy
Logged
Andy, from the now ex-County Palatine of Cheshire

Caring for a European community of melodeons from France, Italy, Germany, Wales and Suffolk!

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Taping thirds on a pokerwork
« Reply #1 on: March 08, 2015, 07:24:46 PM »

Somebody used sellotape or similar on my Lilly. 5 mins to remove the tape, 30 mins to remove the glue.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Taping thirds on a pokerwork
« Reply #2 on: March 08, 2015, 07:28:23 PM »

Use Scotch Magic tape, easier to remove with no residue.

Unfortunately on a Hohner the thirds on the push and pull of a chord button are mostly on different reed plates so it is not just a matter of blocking the port on the reed block. So identify the reed tongue and, if you can see the tongue, tape it over, or if it is the inside reed lift the valve and insert the tape over the reed slot under the valve.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Taping thirds on a pokerwork
« Reply #3 on: March 08, 2015, 07:37:08 PM »

As to which reeds Hohner put the closest tones on the push and pull of a reed plate so for the G/D chord set the following reed plates are used

G Chord G B D   
D ChordF#AD
---------------------------------


MatlockBather

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 131
  • B/C and proud
Re: Taping thirds on a pokerwork
« Reply #4 on: March 08, 2015, 08:46:34 PM »

Unfortunately on a Hohner the thirds on the push and pull of a chord button are mostly on different reed plates so it is not just a matter of blocking the port on the reed block.

Don't I know it! They sound much better now though Lester.

Si
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Taping thirds on a pokerwork
« Reply #5 on: March 08, 2015, 08:48:23 PM »

Unfortunately on a Hohner the thirds on the push and pull of a chord button are mostly on different reed plates so it is not just a matter of blocking the port on the reed block.

Don't I know it! They sound much better now though Lester.

Si

 (:)

vof

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 221
Re: Taping thirds on a pokerwork
« Reply #6 on: March 08, 2015, 08:59:30 PM »

I was unsure whether I would like the result so cut off the thin sticky strip from the edge of a Post-It note which sticks well but can be peeled off without leaving a residue.

V
Logged
Vince O'Farrell
Dino BPII; Hohners: red Erica G/C; couple of 1040s in C and G project boxes.

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Taping thirds on a pokerwork
« Reply #7 on: March 09, 2015, 06:47:23 AM »

I was unsure whether I would like the result so cut off the thin sticky strip from the edge of a Post-It note which sticks well but can be peeled off without leaving a residue.

V

Don't use post it notes for permanency though, they're inclined to dry out and fall off.  :(
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Taping thirds on a pokerwork
« Reply #8 on: March 09, 2015, 07:23:38 AM »

They will be clamped in place by the block, so should be ok. The adhesive only has to work until the block is fitted.

Just don't write important reminders on them first, though.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Taping thirds on a pokerwork
« Reply #9 on: March 09, 2015, 08:18:14 AM »

They will be clamped in place by the block, so should be ok. The adhesive only has to work until the block is fitted.

This does not work on Hohners see my post up a bit from here.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Taping thirds on a pokerwork
« Reply #10 on: March 09, 2015, 09:52:09 AM »

Use Scotch Magic tape, easier to remove with no residue.
Definitely - SMT is good stuff.

Quote
.... or if it is the inside reed lift the valve and insert the tape over the reed slot under the valve.
You can even apply the tape directly on top of the valve. If/when you want to remove the tape, it is possible to carefully peel the tape off starting at the root end, using a pair of tweezers to get it started, then gradually peeling the tape off keeping it flat and as parallel to the reed plate as possible, supporting the gradually-exposed valve by holding it in place as you go.

The advantages in doing it this way are:
1. It is less fiddly to apply in the first place. If the push and pull thirds are both on the same reed plate (though as you say, not usually the case with Hohners), you don't need to cut separate strips of tape for push and pull reeds; one piece the width of the reed plate will do, applied over both push reed tongue and pull reed valve. Otherwise a strip of tape slightly wider than the valve will do fine.

2. There is less risk of leakage on the pull reed as the valve is kept closed completely shut by the tape.

If, on removal of the tape, the valve does come off or is damaged, it's easy to fit another one as it is on the upper side of the reed plate. If the valve adhesive was holding so weakly that the valve comes off, the chances are it was near to failing anyway!
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Taping thirds on a pokerwork
« Reply #11 on: March 09, 2015, 09:59:51 AM »



Quote
.... or if it is the inside reed lift the valve and insert the tape over the reed slot under the valve.
You can even apply the tape directly on top of the valve. If/when you want to remove the tape, it is possible to carefully peel the tape off starting at the root end, using a pair of tweezers to get it started, then gradually peeling the tape off keeping it flat and as parallel to the reed plate as possible, supporting the gradually-exposed valve by holding it in place as you go.


But if both push and pull thirds are on the same plate it is much simpler and easier to tape over the hole in the vent on the base of the reed block.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Taping thirds on a pokerwork
« Reply #12 on: March 10, 2015, 07:30:46 AM »

I use low tack masking tape - the stuff you use in interior decorating. Not sure if it's the same as Scotch Magic Tape, but it tears v easily. I'd be completely lost without a reel of that in the workshop. Also use it on the tuning table to simulate a valve, block off air gaps etc, and it is v good at resticking many times.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Taping thirds on a pokerwork
« Reply #13 on: March 10, 2015, 07:33:34 AM »

But not good long term, it goes hard and crispy, falls off and leaves a gritty residue.  Scotch Magic tape the the best for permanent uses.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Taping thirds on a pokerwork
« Reply #14 on: March 10, 2015, 08:52:47 AM »

Thanks fior that Theo. Luckily I have never used masking tape for a long term solution, so that's ok then.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Taping thirds on a pokerwork
« Reply #15 on: March 10, 2015, 09:22:52 AM »

I agree with you that masking tape is indispensable for many jobs.  I usually put a strip along the top of reed blocks I'm working on so I can mark reeds that need attention without permanently marking the wood.  It also makes a good clamp when gluing very small things.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Taping thirds on a pokerwork
« Reply #16 on: March 10, 2015, 09:49:37 AM »

I use low tack masking tape - the stuff you use in interior decorating. Not sure if it's the same as Scotch Magic Tape....
Scotch Magic Tape is nothing like masking tape. It is a transparent vinyl tape with a special non-gungey (technical term) adhesive which does not degrade over time. It is used especially by draughts-persons and graphics designers for creating montages, paste-ups, etc. The matte surface means that you can write on it with pencil, biro, drawing pens, etc. and it burnishes down to a nearly invisible matte finish which makes it ideal for creating camera-ready artwork. It's really good stuff. I use it for sticking pages of printed music together and adding extra notes, cues, annotations, etc.

For our purposes, as has already been described, it is ideal for taping over reeds to block out thirds in chords. The tape is strong and holds firmly, yet peels off cleanly when required.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Taping thirds on a pokerwork
« Reply #17 on: March 10, 2015, 02:07:16 PM »

And I ought to know this, because I started my working life as draughtsman in the days when we still had A0 drawing boards and drew on film using Rotring pens etc. Great tips on here though. I think I need to go and get a reel of Magic Tape (I had forgotten about that stuff).

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Taping thirds on a pokerwork
« Reply #18 on: March 10, 2015, 03:18:57 PM »

And I ought to know this, because I started my working life as draughtsman in the days when we still had A0 drawing boards and drew on film using Rotring pens etc. Great tips on here though. I think I need to go and get a reel of Magic Tape (I had forgotten about that stuff).
I still have my Double Elephant size drawing board, drawing instruments, Rotring pens and ink, and a few roll ends of film. Do you remember Pounce? I have some of that somewhere too.

And diazo/ammonia process printing and developing. Smells galore! Those were the days...
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Taping thirds on a pokerwork
« Reply #19 on: March 10, 2015, 06:56:31 PM »

Most of my instruments went to my brother, but I still have my 18  inch ruler, with Magic tape strip to stop the ink running. I do remember the print room. I used to work smack next door to Elstree and remember doing umpteen lighting layout drawings for the Empire Strikes back studio... (Sorry..,thread drift)...and surveying studio 5 after Kubrick's lighting caught fire and gutted it (it was the hotel interior for the Shining)...
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal