Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Slipping stop remover  (Read 2850 times)

0 Members and 1 Guest are viewing this topic.

Julia Plumb

  • New Starter
  • Offline Offline
  • Posts: 2
    • Goldthread Music
Slipping stop remover
« on: April 15, 2015, 03:49:29 AM »

Help!

My stop for removing thirds seems to be slippery, and let's itself down, filling my accompaniment with undesired thirds! I know I could tape over the thirds, but does anyone have suggestions for making the darn thing a bit less slippery?

Thanks!
Logged
Serenellini PA, Hohner CBA, Sandpiper Snipe c#/d

Julia Plumb

  • New Starter
  • Offline Offline
  • Posts: 2
    • Goldthread Music
Re: Slipping stop remover
« Reply #1 on: April 15, 2015, 04:10:22 AM »

Fixed!

Turns out reinstalling the chord reed block at a slightly different angle tightened things up so the stop works perfectly. I hope this is at least helpful to someone else, since I feel a bit silly for posting and then immediately solving my own problem! (:)
Logged
Serenellini PA, Hohner CBA, Sandpiper Snipe c#/d

Boxhead

  • Good talker
  • **
  • Offline Offline
  • Posts: 59
Re: Slipping stop remover
« Reply #2 on: April 15, 2015, 08:29:04 AM »

It's not silly, I have this exact issue with my Sandpiper. Is it an easy job to do? could you go into a bit more detail please? I am not particularly confident about opening up the accordion but it would be good if I could sort this for myself. Cheers

Boxhead
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Slipping stop remover
« Reply #3 on: April 15, 2015, 08:33:23 AM »

The first thing to try is to tighten the fixing screws that hold the reed block.  This can be enough.  The reed block should not really be able to be re-positioned at a different angle, but sometimes the locating blocks allow a little movement.  Try tightening the screws first - very easy once you have removed the bellows pins and opened the instrument.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Slipping stop remover
« Reply #4 on: April 15, 2015, 08:36:39 AM »

Remove the bellows pins from the bass end, making sure you can replace the specific pins in the holes they came out of.
Separate the bass end from the bellows.
There will be two reed blocks, one with 12 small reed plates (the chord block) and one with eight large and medium reed plates (Bass block)
Tighten the clamps holding the chord block in place an 1/8th of a turn and try the stop, repeat until happy.
Refit the bass end on the bellows.
Reinsert the pins

And Robert's you father's brother.

Boxhead

  • Good talker
  • **
  • Offline Offline
  • Posts: 59
Re: Slipping stop remover
« Reply #5 on: April 15, 2015, 04:11:04 PM »

It worked ! Thanks everyone. It was disturbing to suddenly find myself  playing major thirds in the middle of a minor tune!

The stop screwed onto a little block and there seemed to be some thread showing, I was able to hold the block and screw the stop further in as well as tightening the screw securing the chord block. 8)  :||:

That was my first time removing the pins and looking inside the instrument.

regards

Boxhead
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Slipping stop remover
« Reply #6 on: April 15, 2015, 05:20:40 PM »

Be careful screwing that stop in or out as it moves the position of the holes in the stop slide relative to the holes in the reed block which will cut off the air passage.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Boxhead

  • Good talker
  • **
  • Offline Offline
  • Posts: 59
Re: Slipping stop remover
« Reply #7 on: April 15, 2015, 05:37:26 PM »

Ah right, how would I know if I have  overdone it?

I have a confession actually, as a private joke in sessions I used to pretend to some that the thirds stop was a tuning device, it was always entertaining twiddling it until the box was 'in tune'... bit like the DFA fader on a mixing desk  >:E.

I guess the joke was on me, I'll leave it alone in future  :||:
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Slipping stop remover
« Reply #8 on: April 15, 2015, 06:46:50 PM »

Ah right, how would I know if I have  overdone it?
Remove the bellows pins to open up the bass end, then remove the chords reedblock. You should then be able to see the slider with the ports in it which controls air entry to the reedblock.

Operate the thirds stop whilst watching the position of the slider ports and how they cover/uncover the holes in the pallet board. If you have screwed the stop knob too far in or too far out, the ports on the slider will be mis-matched with the holes in the pallet board. Adjust the stop knob screw so that when the stop is fully pushed in, the slider ports match up as closely as possible with the pallet board holes; and similarly, when the stop is fully pulled out, the slider should fully blank off the pallet board holes.

It might sound a bit confusing but once you open up the box it becomes really obvious.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Slipping stop remover
« Reply #9 on: April 15, 2015, 06:50:16 PM »

To set it correctly on my Tommy what I did was unscrew it until, when pressed down there was a gap between the bottom of the knob and the casework, then screw it in until the knob just touched the casework. This seemed to work.

Boxhead

  • Good talker
  • **
  • Offline Offline
  • Posts: 59
Re: Slipping stop remover
« Reply #10 on: April 15, 2015, 06:54:41 PM »

Thank you Steve and Lester, I will probably have a bash at this tomorrow.

Everything seems to be working OK atm,

I am reminded of the old saying ' If it works don't fix it' but the temptation to see how this slider thing works will probably be too much for me

Regards

Boxhead  :||:
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Slipping stop remover
« Reply #11 on: April 15, 2015, 06:57:10 PM »

I am reminded of the old saying ' If it works don't fix it' but the temptation to see how this slider thing works will probably be too much for me

Treat it as a learning experience. There's nothing wrong with finding out a bit more about how your instrument works. Go ahead - take a look. If you're reasonably careful with dismantling the box and reassembling it again, you won't do any harm.

Edited to add:
On some instruments, the chords slider runs in a shallow channel in the chords reed block. When refixing the reed block you need to be sure that the slider is located properly in the channel. It might take a bit of jiggling about to get it seated properly before you tighten down the reed block clamp screws.
« Last Edit: April 16, 2015, 07:34:43 AM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Boxhead

  • Good talker
  • **
  • Offline Offline
  • Posts: 59
Re: Slipping stop remover
« Reply #12 on: April 16, 2015, 11:37:18 AM »

Hi everyone,

Well I just opened it up again and examined the slider, it seems I had overdone it slightly as the slider holes weren't fully in line with the pallet holes.

I have turned back the screw stop a few turns so it all lines up, and yes Steve there was a little channel for the slider that I had to line up, thanks for your advice, and everyone else who helped.

All seems well now.

Regards

Boxhead  :||:
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Slipping stop remover
« Reply #13 on: April 16, 2015, 11:50:21 AM »

Well I just opened it up again and examined the slider, it seems I had overdone it slightly as the slider holes weren't fully in line with the pallet holes.

I have turned back the screw stop a few turns so it all lines up, and yes Steve there was a little channel for the slider that I had to line up, thanks for your advice, and everyone else who helped.
Great stuff - well done!  (:)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Slipping stop remover
« Reply #14 on: April 16, 2015, 05:09:56 PM »

You could put a tiny drop of Superglue on the thread of the stop knob to prevent rotation.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Slipping stop remover
« Reply #15 on: April 18, 2015, 05:46:21 PM »

I modded a cajun box that had a similar problem. I drilled a hole in the bottom of the offending block where the slide would cover it where it was thick near the end with the knob. I dropped a lite spring in the hole and a small ball bearing with just enough spring to press it lightly against the sliding valve plate. This worked great ,I magnetized the spring so the ball would stay in the hole.
 A light detent in the plate for the ball to drop into might help for fussy instruments.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal