Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Misaligned Pallet  (Read 3389 times)

0 Members and 1 Guest are viewing this topic.

Vallenato831

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 201
Misaligned Pallet
« on: April 27, 2015, 11:53:10 PM »

Hi all, I have a Corona III with a misaligned pallet.  When I play the button that corresponds to that pallet, the pallet gets stuck on top of the pallet above it.  So the note keeps playing and I have to hit the button a couple times to make the pallet sit properly.  Attached are a few pics showing the issue.  What causes this, the arm or springs or?  Easy fix?
Logged
Corona III x8

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Misaligned Pallet
« Reply #1 on: April 28, 2015, 07:23:34 AM »

Since Steve thinks this is probably wrong I have removed it.
« Last Edit: April 28, 2015, 09:07:30 AM by Lester »
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Misaligned Pallet
« Reply #2 on: April 28, 2015, 09:10:39 AM »

You could do as Lester suggests: remove the pallet and re-glue, and it would probably do the job.

However, there may be more to it than that; I don't think that the pallet was installed incorrectly in the first place. If you look carefully at the bend locations in the lever arms, you can see that the bend in the affected item is also out of alignment with the equivalent bends in the neighbouring lever arms, by the same amount that the pallet is mis-placed. This suggests to me that the entire lever arm has become slightly distorted somehow, perhaps bent out of shape accidentally at some stage. An overall flattening of the lever arm angles would result in an overall lengthening, and misalignment of the pallet as shown. This might also reveal itself in that the button height for that particular lever being different from the rest.

It would be worth checking the bend angles of the affected lever arm with all the others on that row to see if there is any difference. If so, it should be possible to correct the pallet alignment simply by careful restorative bending back to the the proper shape.

Try to reposition the pallet back to its proper, correct position and hold it there in the closed position with a finger. You should then be able to see how and where the lever arm is distorted and what further remedial bending is required to maintain the pallet in its proper position. Useful tools will be small round-nosed pliers which can reach in between the lever arms.

Work carefully and gently, a bit at a time and test all the while to ensure that the pallet is still sealing properly.

(Edited to amend wording with ambiguous meaning) 
« Last Edit: April 28, 2015, 11:58:14 AM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Misaligned Pallet
« Reply #3 on: April 28, 2015, 10:10:19 AM »

Worth checking for incorrect bends, but I don't think that is the cause.   

Another possibility is that the the glue is not holding and has allowed the pallet to slide along the lever.   If this is the case it might slide back quite easily, and would then need to be fixed to prevent it moving again.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Misaligned Pallet
« Reply #4 on: April 28, 2015, 10:42:33 AM »

Since Steve thinks this is probably wrong I have removed it.
Come on Lester, no need to be like that; your diagnosis and solution were perfectly valid, so do please repost them. It's just that there are other possibilities too. It's can be hard trying to give correct advice just by looking at a photo or two and not having the actual instrument directly to hand. Theo is uncertain about my diagnosis too, which is fine with me. I'm leaving my post as it is though, just to illustrate the various alternatives.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 613
Re: Misaligned Pallet
« Reply #5 on: April 28, 2015, 11:06:56 AM »

You can see clearly on the 2nd photo middle pallet is sticking out of line and not at the same level as the others, take it off and re glue it in correct position in line with the rest...also you could try to bend the top lever arm to left a bit to make the gap smaller so under pallet won’t  get stuck..make the gap smaller by bending the top arm a bit  :||:
Logged

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Misaligned Pallet
« Reply #6 on: April 28, 2015, 12:03:47 PM »

LOL *dons helmet*

Since this is the only one that is obviously out, it may be reasonable to assume that whoever refixed the pallets wasn't a complete dork.
Therefore we might assume that originally they were all straight.

Don't think the glue has shifted.

Hypothesis - lever has taken a knock (or suffered other abuse). A likely symptom would be the lever position is now different, which we (apparently) see. Therefore hypothesis seems reasonable.

Therefore review the lever alignment against its peers. If it's out of kilter, consider straightening it. If no fault found, or it looks too much like hard work, re-gluing the pallet will most likely work.

*repositions head below parapet*
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Misaligned Pallet
« Reply #7 on: April 28, 2015, 12:34:24 PM »

The pallets have clearly been removed and refitted at some stage, as that is most definitely not a Hohner factory adhesive. While I agree there seems to be a slight discrepancy between the levels of the ends of the levers, there is far more of a difference between the ends of the pallets, which suggests to me that the offending pallet was either reattached out of line or it slid upwards on the arm before the glue set properly. The lower parts of the pallet levers look pretty much properly aligned. I'm with Lester - remove the pallet and reattach it in its proper alignment.
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Vallenato831

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 201
Re: Misaligned Pallet
« Reply #8 on: April 28, 2015, 02:14:51 PM »

Thanks all!  I'm at least the 2nd owner of this box.  I have no clue what was done to it prior.  I do know that a couple reed plates were rewaxed, because the was is a different color than the rest.  I dont know if the pallets were redone.  They all appear to be the same, glue wise. 

I tried the simple way first that I believe Lester recommended.  The pallet moves quite easily, and it is not glued in properly, just took some slight pressure with 1 finger to move it back into alignment.   After doing so, it seated in the right location and that pallet is perfectly flush too.  I just dont have a soldering iron to reheat that glue to permanently fix it at the moment.  You guys are a bunch of sleuths!!!  Appreciate it! 
Logged
Corona III x8

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Misaligned Pallet
« Reply #9 on: April 28, 2015, 02:40:31 PM »

that is most definitely not a Hohner factory adhesive.

Not common on older Hohners, but this sort of adhesive is common on more recent Hohners.

The pallet moves quite easily, and it is not glued in properly, just took some slight pressure with 1 finger to move it back into alignment.   After doing so, it seated in the right location and that pallet is perfectly flush too.  I just dont have a soldering iron to reheat that glue to permanently fix it at the moment.  You guys are a bunch of sleuths!!!  Appreciate it! 

Just as I suspected!  A small dollop of pva at the end of the existing glue should hold it if it starts to move again.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Vallenato831

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 201
Re: Misaligned Pallet
« Reply #10 on: April 28, 2015, 03:17:53 PM »

Yeah looks like this Corona is recent, maybe 10 years old or so, Chinese box. 

So, the PVA glue is just the white school glue, Elmers right?  Or is it the crazy glue? 
Logged
Corona III x8

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Misaligned Pallet
« Reply #11 on: April 28, 2015, 04:12:46 PM »

White glue.

There is a pictorial guide to different ages of Coronas here http://www.peterunbehauen.de/p/05peterunbehauen.html
« Last Edit: April 28, 2015, 04:18:15 PM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

tom f

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 112
Re: Misaligned Pallet
« Reply #12 on: April 28, 2015, 06:30:25 PM »

Thanks all!  I'm at least the 2nd owner of this box.  I have no clue what was done to it prior.  I do know that a couple reed plates were rewaxed, because the was is a different color than the rest.  I dont know if the pallets were redone.  They all appear to be the same, glue wise. 

I tried the simple way first that I believe Lester recommended.  The pallet moves quite easily, and it is not glued in properly, just took some slight pressure with 1 finger to move it back into alignment.   After doing so, it seated in the right location and that pallet is perfectly flush too.  I just dont have a soldering iron to reheat that glue to permanently fix it at the moment.  You guys are a bunch of sleuths!!!  Appreciate it!
I came across this problem recently on a new Morgane.  On this one it was one of the base end pallets which was sliding forward and jamming on the lever frame.  Initially I tried to fix it by re-heating the glue but this didn't work very well.  The glue used on these boxes appears to be more like a mastic than a glue and doesn't respond well to re-heating.  In the end I took the pallet off, cleaned it (making sure it was grease free) and refixed it using a proper hot glue gun.  It seems to have cured the problem.
Logged

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Misaligned Pallet
« Reply #13 on: April 28, 2015, 06:48:19 PM »

that is most definitely not a Hohner factory adhesive.

Not common on older Hohners, but this sort of adhesive is common on more recent Hohners.


Thank you, Theo - I stand quite happily corrected. Actually that possibility dawned on me about 5 minutes after I'd posted..... ::)
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Vallenato831

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 201
Re: Misaligned Pallet
« Reply #14 on: April 29, 2015, 10:03:51 PM »

Thanks again!  I'm going to try and remove the pallet, clean it up and hot glue back together again.  Wish me luck!  And I agree it doesnt seem like real glue, almost like melted plastic, i dont know. 
Logged
Corona III x8

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Misaligned Pallet
« Reply #15 on: April 30, 2015, 06:20:56 AM »

Thanks again!  I'm going to try and remove the pallet, clean it up and hot glue back together again.  Wish me luck!  And I agree it doesnt seem like real glue, almost like melted plastic, i dont know.

It looks as if a hot glue gun was used. It looks like melted plastic when cold.
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Vallenato831

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 201
Re: Misaligned Pallet
« Reply #16 on: October 03, 2015, 02:51:09 PM »

White glue.

There is a pictorial guide to different ages of Coronas here http://www.peterunbehauen.de/p/05peterunbehauen.html

I still haven't done this repair yet.  I bought a heat gun to re do it.  But the heat gun wont fit in between pallet levers.  I'd have to somehow take off all of the assembly. 

Would krazy glue work as good as the pva?  I can probably squeeze in a few drops. 
Logged
Corona III x8

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Misaligned Pallet
« Reply #17 on: October 03, 2015, 04:26:53 PM »

White glue.

There is a pictorial guide to different ages of Coronas here http://www.peterunbehauen.de/p/05peterunbehauen.html

I still haven't done this repair yet.  I bought a heat gun to re do it.  But the heat gun wont fit in between pallet levers.  I'd have to somehow take off all of the assembly. 

Would krazy glue work as good as the pva?  I can probably squeeze in a few drops.

No it would run down into the groove where the lever lies and make it impossible to ever remove again.  A small patch of cloth coated with pva will fix it.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Vallenato831

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 201
Re: Misaligned Pallet
« Reply #18 on: October 03, 2015, 11:25:31 PM »

Thanks Theo.  Took your advice to not use krazy glue.  I went ahead and managed to get it done via hot glue.  Scraped off the old glue real well.  And somehow squeezed the glue gun in between levers.  It appears to have solved the problem.  I can no longer make the pallet slide off the lever with ease. 
Logged
Corona III x8
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal