Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Lowering Button Height  (Read 7080 times)

0 Members and 1 Guest are viewing this topic.

Vallenato831

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 201
Lowering Button Height
« on: April 30, 2015, 03:48:10 PM »

Hi all, I have an older German made Corona that I need to lower the button heights.  I'd like to lower by about 1mm to all the buttons on the treble side.  I found the following fix quoted below.  Is that fix the correct method to making this adjustment?

Quote
If you’d like to lower the buttons then first remove the grille to expose the pallets. Hold down the pallet while pushing firmly on its corresponding button. This will bend the lever and lower the button. A technician will do the same thing. If you do this carefully across all buttons taking care to be consistent, then you will have a uniformly lower button height.
Logged
Corona III x8

deltasalmon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1002
Re: Lowering Button Height
« Reply #1 on: April 30, 2015, 04:20:58 PM »

From personal experience (With a Weltmeister, not a Corona) I found it is very difficult to be consistent with lowering the buttons this way. The levers had flex in them and it was difficult to be exact with the adjustment.

I'm not sure if others have another way of doing it or not but if you plan on doing it this way be prepared to spend time adjusting and readjusting... and readjusting...
Logged
Sean McGinnis
Bordentown City, NJ, USA

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Lowering Button Height
« Reply #2 on: April 30, 2015, 05:43:38 PM »

That is correct, there is a lot of careful work needed to do the job. Because of the design of Hohner levers there is a tendency for the button to also move sideways when you bend it lower, so be prepared to compensate for that too.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Lowering Button Height
« Reply #3 on: May 01, 2015, 07:07:41 AM »

 I also don't really like doing it this way as it puts a lot of stress on that folded joint that is the pivot on hohners. These will stress crack at the heel once and awhile.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

syale

  • The Terrier
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
  • When will this MADness stop?
Re: Lowering Button Height
« Reply #4 on: May 01, 2015, 01:28:48 PM »

Can you remove the buttons and grind 1mm from the profile at the end of the lever?

Stephen
Logged
HA114 C/G/A/D, 2915 G/C. Liliput, Club IIB C/F Dino Baffetti Modell 22 B Twitter: @syale

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Lowering Button Height
« Reply #5 on: May 01, 2015, 02:43:07 PM »

How about adding a layer of felt to the valves?

911377brian

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1518
Re: Lowering Button Height
« Reply #6 on: May 01, 2015, 04:42:01 PM »

How would that work, Bryan? 8)
Logged

911377brian

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1518
Re: Lowering Button Height
« Reply #7 on: May 01, 2015, 04:43:44 PM »

Did'nt mean to send that emoticon....
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Lowering Button Height
« Reply #8 on: May 01, 2015, 04:45:20 PM »

Adding an extra layer of pallet facing lifts the pallets, which lowers the buttons.
IMO that is making a lot of unnecessary work unless the pallet facings need replacement.  Lowering the buttons by bending the levers is a perfectly doable method, it just needs care.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Lowering Button Height
« Reply #9 on: May 01, 2015, 04:45:34 PM »

How would that work, Bryan? 8)

Bryan was, at a educated guess, talking about the pallets rather than the valves (may well be a two nations separated by a common language thing)

Any way bending the mechanism is the way to go, gently and in little bits, this will allow the height to be set as desired and, unless you are a gorilla, very unlikely to break anything. I have done many this way. As Theo said though Hohner mechs will twist sideways when you make the adjustment so some further alignment will be needed.

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Lowering Button Height
« Reply #10 on: May 01, 2015, 08:58:58 PM »

How would that work, Bryan? 8)

Bryan was, at a educated guess, talking about the pallets rather than the valves (may well be a two nations separated by a common language thing)

 (:)
Mutual words with different and multiple meanings.  Actually usually referred to as flappers in my neck of the prairie.

Vallenato831

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 201
Re: Lowering Button Height
« Reply #11 on: May 01, 2015, 11:29:09 PM »

I think I'll give it ago and make sure to be extra careful.  I'm going to go with the bend method for sure.  The flappers/pallets have enough felt I believe.  Thanks!!
Logged
Corona III x8

KLR

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 640
Re: Lowering Button Height
« Reply #12 on: April 26, 2023, 08:57:24 PM »

The fact this hasn't been brought up means it almost certainly can't be done, but why not just install shallower buttons?  Or grind the existing buttons down. I'd really like this for my Castagnari Sharon, which has such tall/small buttons it gives me sore fingers after awhile. 
Logged

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Lowering Button Height
« Reply #13 on: April 27, 2023, 09:48:29 AM »

How about raising the keyboard? 1mm veneer, drill holes, varnish and glue - would that work?
Logged

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Lowering Button Height
« Reply #14 on: April 27, 2023, 11:10:04 AM »

I wonder how Sharon Shannon copes with the failings of this instrument.

https://www.allaboutaccordions.com/castagnari-accordions
« Last Edit: April 27, 2023, 11:34:58 AM by Tone Dumb Greg »
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Lowering Button Height
« Reply #15 on: April 27, 2023, 02:10:55 PM »

The fact this hasn't been brought up means it almost certainly can't be done, but why not just install shallower buttons?  Or grind the existing buttons down. I'd really like this for my Castagnari Sharon, which has such tall/small buttons it gives me sore fingers after awhile.

It could most certainly be done. It’s just easier to lower the existing buttons than replace with new. I’ve yet to come across a box where the buttons couldn’t be lowered.
Logged
C#/D player

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Lowering Button Height
« Reply #16 on: April 27, 2023, 03:29:21 PM »

Quote
I wonder how Sharon Shannon copes with the failings of this instrument.

I would guess that hers is a special, made to her specs. I tried a Dinn 111 and the buttons were to high for me compared to my Irish Bouebe
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Lowering Button Height
« Reply #17 on: April 27, 2023, 05:52:36 PM »

There is a special tool which makes this task very easy and fast. Looks and works like a cigar cutter.
Logged

KLR

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 640
Re: Lowering Button Height
« Reply #18 on: April 27, 2023, 10:00:11 PM »

How about raising the keyboard? 1mm veneer, drill holes, varnish and glue - would that work?

Raising the keyboard cover, you mean?  That's a great idea.  A shim underneath the existing cover would be reversible, too, the only problem is that the cover is held in place by three screws and the other side is held in place by the grille, which would need shortened a little. 

Quote
I wonder how Sharon Shannon copes with the failings of this instrument.

She used to play stepped keyboard Castas, and maybe just doesn't do much sliding around.  Sliding is what gets to me about this box, otherwise I'm quite fond of it.

Quote
There is a special tool which makes this task very easy and fast. Looks and works like a cigar cutter.

Interesting!  I'll have to ask my repair guy about that. 
Logged

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Lowering Button Height
« Reply #19 on: April 27, 2023, 10:06:25 PM »

There is a special tool which makes this task very easy and fast. Looks and works like a cigar cutter.

Do you have a link to an example and where to buy it, please?
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal