Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: To wax or not to wax ... that is the question.  (Read 6412 times)

0 Members and 1 Guest are viewing this topic.

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
To wax or not to wax ... that is the question.
« on: June 22, 2015, 11:56:41 AM »

Prompted by another thread where there seems to be some kind of disagreement by people who know what they're talking about on this matter, I'd like to know all the pros and cons of using wax or pinning/screwing the reeds down in to an airtight gasket of some sort.

This sort of question needs a photo!

Having said that it's usually reckoned that reeds pinned onto leather is a superior construction method than wax.  If valves are old you will just have to take the reeds off anyway.  The worst you will have to do is to remove and replace the leather gaskets. A lengthy job but not particularly difficult.

This sounds like a rather bold statement. I've come across too many loose reeds that had been pinned onto leather or cork, even in recently built instruments.  High quality wax applied by an expert offers many advantages. And what's more,  after waxing the reeds you can still use pins or screws (as I have done for many years in my own boxes) to ensure  good contact with the block.

Most of my instruments have waxed in reeds - but some that I own use the second method and I can not tell any noticeable difference in the quality of sound they make - and the only time I have ever suffered from reeds falling out has occurred in instruments that have the waxed in!

I have to say that from a purely functional point of view I am definitely drawn towards the methods that don't use wax because it seems far better suited for regular maintenance of the reeds.  Having done a bit of restoration and emergency repairs on my own instruments, I have developed a seething hatred of wax, the way it gets everywhere, the way it makes you hesitate to remove a reed plate to fix something on the other side because of the laborious way you need to cut it out, clean it off and then have all the gubbins needed to wax it back in to place.  Let's forget the bit about accidentally spilling a stream of hot wax over the reed itself or valves because obviously nobody ever does that  >:E
I also hate the way it goes brittle and little bits break off after many years of use - ending up inside the reeds to cause further problems.

So tell me - why does almost everybody use wax to hold the reeds.  Does it really give a better contact with the reed blocks than pinned or screwed reeds on leather or cork?
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: To wax or not to wax ... that is the question.
« Reply #1 on: June 22, 2015, 12:04:58 PM »

The use of wax is probably down to cost on the cheaper boxes - just lay on the reed and run wax around from a vat of wax, 2 minute job - fir leather/olivice to the block set the reeds on screw/pin each reed individually, not a 2 minute job.

As too quick jobs, I don't cut reed out I lever then out from the inside (with some care, but I've never had a problem), do whatever needs doing and then pop the reed back in with the wax still attached and run round with waxing iron, of penknife/ciggy lighter if out in the wilds.

Just don't do what i recently had to rectify in a customers box and wax reeds in onto the existing leather gaskets. It was a leaky mess.

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: To wax or not to wax ... that is the question.
« Reply #2 on: June 22, 2015, 12:06:54 PM »

I'm fairly sure Emmanuelle Pariselle on his melodeon building courses doesn't use wax for the exact reasons you've beautifully  illustrated.
Q
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: To wax or not to wax ... that is the question.
« Reply #3 on: June 22, 2015, 12:08:19 PM »

So tell me - why does almost everybody use wax to hold the reeds.  Does it really give a better contact with the reed blocks than pinned or screwed reeds on leather or cork?

My guess is that it is quicker and therefore cheaper to use wax, especially in a factory where a skilled waxer can do a set of reeds in a remarkably short time.  I've used both methods and fixing a set of reeds to blocks with wax is considerably quicker, all you need is a clean flat side to the block and its a matter of a couple of minutes to wax each bank of reeds.  Wax will also cover over any small holes where the reed plate is not an exact match to the length of a reed chamber.   In contrast to prepare a block for fitting reeds on gaskets with pins or screws takes much more time.   Reed chamber sizes have to be adjusted more carefully, the gasket material has to be cut and fixed, pilot holes may need to be drilled for fixing screws and then the reeds fitted.   But the big advantage is the greater ease of reed maintenance.

Written at the same time as Lester!   We agree on that then.   But I don't agree with re-using the old wax, unless its a field repair and there is no fresh wax available. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: To wax or not to wax ... that is the question.
« Reply #4 on: June 22, 2015, 12:11:10 PM »

I'm fairly sure Emmanuelle Pariselle on his melodeon building courses doesn't use wax for the exact reasons you've beautifully  illustrated.
Q

And I found making both my Pariselles air tight was a right royal pain and am sure waxing would have been quicker/easier.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: To wax or not to wax ... that is the question.
« Reply #5 on: June 22, 2015, 12:13:26 PM »

I'm fairly sure Emmanuelle Pariselle on his melodeon building courses doesn't use wax for the exact reasons you've beautifully  illustrated.
Q

And I found making both my Pariselles air tight was a right royal pain and am sure waxing would have been quicker/easier.

I've had several Pariselle course boxes back from the owner/builder to modify the layout, and in that situation the absence of wax is a blessing.

Removing wax from old boxes where it is dry and brittle is pretty straightforward, but moving reeds with new wax is not.  The stuff can stick to anything!
« Last Edit: June 22, 2015, 12:15:17 PM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

AirTime

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 979
Re: To wax or not to wax ... that is the question.
« Reply #6 on: June 22, 2015, 03:08:18 PM »

This is a topic of interest to me as my 1920's Hohner has a tendency to fall out of tune  because the screws/pins holding the reeds in place are not entirely secure. I have thought about having them waxed in for simplicity, but have hesitated to do this, as once done, there's no turning back.
Logged
1920's BbEb Hohner; 1920's  AD Koch; 1910 (?) One-row Hohner in D,  1910's GCB Maga Ercole; ; AD 1950's Pistelli, CF Sandpiper, CF Preciosa, BbEb Preciosa.

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: To wax or not to wax ... that is the question.
« Reply #7 on: June 22, 2015, 05:33:00 PM »

The reason why E.P. doesn't use wax in his courses is a very practical one: everybody can use a screwdriver, while reed waxing skills*) can, by most people anyway, not be  acquired in a matter of days or weeks . But as a professional melodeon maker, I'm really grateful that there is such a thing as wax and am actually always looking forward to that stage in the production process.
*) which means: no soldering iron...
« Last Edit: June 22, 2015, 05:36:52 PM by diatonix »
Logged

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: To wax or not to wax ... that is the question.
« Reply #8 on: June 22, 2015, 06:09:09 PM »

Having taken an old concertina apart recently I was pretty surprised to find the reeds kinda just slotted into position. Have any makers experimented with something similar on bigger boxes, or is there a reason why it doesn't scale? (note that this was also a fairly cheap and old concertina, so I'm not even sure if most concertinas were made this way)
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: To wax or not to wax ... that is the question.
« Reply #9 on: June 22, 2015, 06:14:35 PM »

Having taken an old concertina apart recently I was pretty surprised to find the reeds kinda just slotted into position. Have any makers experimented with something similar on bigger boxes, or is there a reason why it doesn't scale? (note that this was also a fairly cheap and old concertina, so I'm not even sure if most concertinas were made this way)

All top quality concertinas where/are built that way with reeds that slot into the reed pan. The slots and reeds are both beveled on the edge to create an air tight seal. My guess is accordions are not built that way as the main driver for using the slot method is compactness of design which is not required in a bigger accordion.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: To wax or not to wax ... that is the question.
« Reply #10 on: June 22, 2015, 06:16:40 PM »

Should we ask an expert on waxing - Mr Miyagi  (:)

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: To wax or not to wax ... that is the question.
« Reply #11 on: June 22, 2015, 06:43:15 PM »

I think Lester has a good point.
I presume wax not only holds in the reeds but also fills up the minute cracks and crevices at the same time ensuring it is airtight.
Q
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: To wax or not to wax ... that is the question.
« Reply #12 on: June 22, 2015, 06:47:51 PM »

The reason why E.P. doesn't use wax in his courses is a very practical one: everybody can use a screwdriver, while reed waxing skills*) can, by most people anyway, not be  acquired in a matter of days or weeks . But as a professional melodeon maker, I'm really grateful that there is such a thing as wax and am actually always looking forward to that stage in the production process.
*) which means: no soldering iron...

All true, but more than once I have heard EP saying in a big voice "I hate wax!"
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: To wax or not to wax ... that is the question.
« Reply #13 on: June 22, 2015, 06:53:17 PM »

Having taken an old concertina apart recently I was pretty surprised to find the reeds kinda just slotted into position. Have any makers experimented with something similar on bigger boxes, or is there a reason why it doesn't scale? (note that this was also a fairly cheap and old concertina, so I'm not even sure if most concertinas were made this way)
As far as I know, this method of construction was used only by English makers (until more recently, perhaps). German concertinas, especially the cheap export ones, used long plates with 5 or more reed pairs. These were seated on candlewick cord, and retained by bent nails which could swivel to release the plates. Cheap accordeons and melodeons used the same method.
Don't know when they started to use wax.
Bevelled individual reeds is a relatively expensive method and needs special tooling to cut the slots. The other methods can be done by hand.
« Last Edit: June 22, 2015, 06:55:10 PM by malcolmbebb »
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: To wax or not to wax ... that is the question.
« Reply #14 on: June 22, 2015, 07:03:19 PM »

I'm sure I've heard somewhere...... when a top quality or at least good quality English Concertina or Aeola was being sold for something in the region of 8-10 guineas, a melodeon at the same time was going out for about 30/-
Whatever the exact money is, the point made is that concertinas were being made by incredibly highly skilled people commanding a much higher price. Therefore they could afford to employ people to make the reeds fit in exactly into the reed pan. The melodeon of the same era was much more a basic construction 'for the people' as opposed to a parlour instruemnt for the wealthy.
Q
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: To wax or not to wax ... that is the question.
« Reply #15 on: June 22, 2015, 08:51:10 PM »

Well - everyone seems to be saying that it's easier and cheaper to use wax ... whereas the professional melodeon maker says that it's a far more difficult skill but quite easy once you become skilled in it.

I've had some amateur experience of proper waxing (using a spoon and a hot pot) - and I can testify to the fact that it's bloody difficult ... and very frustrating to start with.  But I have also seen the beautifully accurate and clean wax work done by some of the best makers and repairers.  So I completely agree with diatonix's point.

However - I'd love to hear any reasons why a hand made instrument shouldn't use a waxless approach.  Is it really so hard to get an airtight seal or a contact that won't come loose?  And is there any perceivable difference in the sound of an instrument that is waxed and one that uses screws or nails?
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: To wax or not to wax ... that is the question.
« Reply #16 on: June 22, 2015, 08:54:35 PM »

FWIW Marcus Concertinas use brass screws on to a leather base.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: To wax or not to wax ... that is the question.
« Reply #17 on: June 23, 2015, 08:57:52 AM »

If wax is so good, why don't we use for engine cylinder heads...... Pound for pound they are under just as much stress.
 Broadland Boy need not reply. Yours etc. Diamond Geezer.
On a serious note, wax is traditional and therefore still used. Shoot me down for saying you are all Luddites. There are so many products on the market now that will knock wax into a cocked hat.
   Hot glue gun anyone?  >:E
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: To wax or not to wax ... that is the question.
« Reply #18 on: June 23, 2015, 09:02:58 AM »

If wax is so good, why don't we use for engine cylinder heads...... Pound for pound they are under just as much stress.
Care to expand
Quote
On a serious note, wax is traditional and therefore still used. Shoot me down for saying you are all Luddites. There are so many products on the market now that will knock wax into a cocked hat.
   Hot glue gun anyone?  >:E
Can you give examples of modern products that have the same gripping/sealing properties as wax but are as easy to remove/rework?

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: To wax or not to wax ... that is the question.
« Reply #19 on: June 23, 2015, 09:12:41 AM »

NO! But they must be out there Lester.
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal