Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Repairing Hohner woodwork  (Read 3472 times)

0 Members and 1 Guest are viewing this topic.

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Repairing Hohner woodwork
« on: June 22, 2015, 11:58:40 AM »

So I may have just acquired a new project ::) (I have just sold a box, so in theory I'm currently in profit at least!)
I've just won what looks like a largely very decent condition Erika from German eBay; I'll find out just what it's like when it arrives, but the only major exterior flaw I could see was some not insignificant buckle-rash on the top and bottom panels on the treble box. I was planning on sanding the existing finish back and redoing it, but I'm not sure what process was originally used for varnishing it. Is it French polish with a wax finish?



Planning on getting it the Rowbotham treatment, but I'd quite like to sort out the bits I can do first and a bit of sanding and polishing should be within my grasp. Hopefully it's not a complete dog! Comes with its original case too, which I'll give a nice spruce up as leather is more within my existing expertise.

Apologies if this has been covered before, but most threads I've found about Hohner restoration have been in regard to presswood, pokerwork, or celluloid finishes.
« Last Edit: June 22, 2015, 03:21:54 PM by robotmay »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Repairing Hohner woodwork
« Reply #1 on: June 22, 2015, 12:10:11 PM »

Before you reach for the abrasive paper try a few coats of french polish applied with a rubber.  It works very well with the finish on these boxes.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: Repairing Hohner woodwork
« Reply #2 on: June 22, 2015, 12:51:37 PM »

Thanks Theo; I'll give that a try. Is there a finishing coat of something else on top of the polish?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Repairing Hohner woodwork
« Reply #3 on: June 22, 2015, 12:59:19 PM »

Perhaps a wax furniture polish.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Repairing Hohner woodwork
« Reply #4 on: June 22, 2015, 02:12:18 PM »

Just to be clear, you are talking about a french polishing rubber made from wadding and cotton fabric, not a giant pencil eraser.....?   ;)

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: Repairing Hohner woodwork
« Reply #5 on: June 22, 2015, 02:37:02 PM »

Haha that was the first thing that popped into my head too. I was assuming it was the former :D
Not tried french polishing before so I'll practice quite a bit on some scrap before I try it on the box. Any idea what colour shellac it's likely to be (or if I should just use pale/transparent shellac)? I'm assuming that the answer would likely depend on the quality of the photos, unless there's a standard sorta colour that was used on these boxes!
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Repairing Hohner woodwork
« Reply #6 on: June 22, 2015, 03:21:15 PM »

I usually use "button polish" which is a light tan colour.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Repairing Hohner woodwork
« Reply #7 on: June 22, 2015, 04:41:18 PM »

Button polish here too.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: Repairing Hohner woodwork
« Reply #8 on: June 22, 2015, 05:09:02 PM »

Great, thanks guys. Any recommended brands or places to buy the polish (and premixed or flakes)?

Now to wait and see what sorta condition it's in when it turns up. From the pictures the rest of it looks pretty nicely preserved, particularly the bellows:






I might be able to rescue the original straps too, unless they've snapped or cracked too much.
Logged

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: Repairing Hohner woodwork
« Reply #9 on: June 27, 2015, 11:15:49 AM »

It arrived yesterday!
It's identical to how it looked in the photos. The bellows are incredibly tight and basically perfect, apart from the slight tape wear on the bottom. The grill is a bit bent and needs a polish and the keyboard might need a lick of paint. Is there a specific type of paint to use for these keyboards?

The woodwork is the same as the photos, bar a small old strap bracket hole on the top I hadn't seen and which has been half-arsedly filled, so I'll probably redo that before fixing the polish. Anyone got a recommendation on how best to do that? I was thinking of boring it out and fitting a small wooden plug inside it before cutting/sanding it off, not sure if that's the best solution.
Logged

Sue

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 100
Re: Repairing Hohner woodwork
« Reply #10 on: June 27, 2015, 03:41:02 PM »

I'm also thinking of repainting the thumb board of an old Hohner and wondering if there is a particular type of paint to use.
Sue
Logged
Oakwood D/G, Karel van der Leeuw D/G
G/D anglo concertina
CRY HAVOC MORRIS

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Repairing Hohner woodwork
« Reply #11 on: June 27, 2015, 03:48:52 PM »

Car spray paint works well.  Strip of all the old paint first and use the primer designed for the paint you use.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: Repairing Hohner woodwork
« Reply #12 on: September 16, 2015, 10:03:11 AM »

So I've finally filled the old strap bracket holes and had a first bash at polishing. I started with the bottom panel on the treble side in case I cocked it up, but the finish I'm getting so far seems fine. However I don't have any experience of doing this before; is it possible to merge this raw-wood section with the old polish? Or should I strip the panel back entirely and do it evenly from scratch?



It's in the same condition on the top of the treble side, so ideally I'd like a fairly inconspicuous repair, but I don't mind polishing it up from scratch if that's necessary, as the rest of the box is quite light in colour anyway and should match up.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Repairing Hohner woodwork
« Reply #13 on: September 16, 2015, 10:39:51 AM »

If you want an even colour you need to do get that right before you start to apply the polish.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: Repairing Hohner woodwork
« Reply #14 on: September 16, 2015, 10:42:29 AM »

Ah ha, any idea what stain was used on these originally, or what a good replacement would be?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Repairing Hohner woodwork
« Reply #15 on: September 16, 2015, 11:44:52 AM »

I'm not absolutely sure, but I don't think a stain was used, just a coloured finish.   The ones I've seen have a pretty thick layer of finish so, even if it is shellac, it would not have been applied with a rubber in the traditional French polish manner, more likely it would have been sprayed.  French polish comes in several different colours, button polish is a a  light tan, the darkest is usually called garnet polish, but there are other colours available including black. 

You should be able to get an even colour of bare wood by removing the old finish with paint stripper and steel wool, and the using abrasive paper and/or a cabinet scraper to get a nice clean and smooth new surface.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: Repairing Hohner woodwork
« Reply #16 on: September 16, 2015, 12:06:27 PM »

Ah thanks Theo. That makes sense. The finish on this box seems very thin as it removes very easily with just a bit of abrasive paper. The back of the box is quite a lot darker than the top/front; I wonder if it has been lightened over the years by being in strong sunlight (the darker finish under fixtures seems to indicate this), or possibly refinished in the past.

I might order some garnet shellac too then and see if a few layers of that underneath the button polish brings it up to a similar colour. I don't want to go too dark though as the front of the box is quite light and I don't want to get too enthusiastic with it in case I remove the graphics.

I'll take a few photos tonight of the bits I'm trying to touch up, just in case you have any advice to stop me doing something stupid ;D
Logged

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Repairing Hohner woodwork
« Reply #17 on: September 16, 2015, 01:05:55 PM »


 and I don't want to get too enthusiastic with it in case I remove the graphics.


That concern is what has stopped me from refinishing my own Club Victoria. Unfortunately, the front panels of the melodeon are in by far the worst condition.

I have spoken to a few local business who can produce replacement transfers/decals, but unless I want a fairly large number it seems prohibitively expensive. I did consider doing just that and then offering left overs for sale on this site (10% to m.net obviously!!!), and I'm still thinking about it, but was wondering if any one had gone down this track already???

Maybe there is something that can be made up using a home computer with an inexpensive graphics programme and a half way decent printer. (Unfortunately, not too clued up on computer graphics.) Any advice would be most welcome.

(Sorry, slight thread drift here.)
Logged
Tuner/repairer, now retired.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Repairing Hohner woodwork
« Reply #18 on: September 16, 2015, 01:24:11 PM »

If you need to reproduce the graphics I can think of two possible methods that could both be inexpensive.
1 make some stencils out of card and use spray paint.
2 if you know someone with screen printing kit you could use similar stencils as a mask to screen print direct onto the box.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: Repairing Hohner woodwork
« Reply #19 on: September 16, 2015, 03:42:53 PM »

Has anyone used these shellac filler sticks in the past? https://www.toolsforworkingwood.com/store/more/LB-shellacfillers.html
Just wondering if that'd be suitable for filling the gouge out of the finish on the back of the treble box, or whether I just try to refinish it similarly to the rest of the box. I'll post some photos of the various bits I'm trying to fix this evening, in case anyone has better ideas for fixes.
Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal