Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Installing valves  (Read 1374 times)

0 Members and 1 Guest are viewing this topic.

KLR

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 640
Installing valves
« on: July 06, 2015, 09:38:44 PM »

Kind of a commonsensical question but how do you go about affixing valves?  I've simply been putting a dab of glue on a board, smush end of valve in glue, wipe on board to get rid of excess, put in place, ensure contact with a toothpick.  Seems to work but there's always a wrinkle with these things.

Also, how would you go about trimming a vinyl valve?  Or a leather one for that matter.  Sharp scissors OK, or should I do it right with a razor blade or the like to prevent the surface curling?  Although I've been practicing with homemade valves and they don't seem to distort too much when cut with snips.

And speaking of toothpicks, I tried one to get rid of the excess glue around rivets when cleaning up, but that wood they use of course is really mushy so I made one out of boxwood scrap, which is anything but.  If you have a woodworking shop nearby you could find something of a comparable hardwood to use as a scraper.
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Installing valves
« Reply #1 on: July 06, 2015, 10:41:58 PM »

When doing the valves on my one row,. I just held tub of glue squeezed a little to form a small dab and rubbed the end of valve on it and applied it to reed plate.
This is how experts here suggested doing it,  when i ask the qustion.
I think the glue would be less affected by air with this method, as I found that if not use quick enough the glue skins over and becomes harded to work with.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Installing valves
« Reply #2 on: July 06, 2015, 11:15:04 PM »

Being an amateur fixer, I have used the method for applying glue that you mentioned with good success. For a 'board', I use a post-it cut into about four strips. Each strip holds the surface in place and allows me to do a pair of reeds (4 valves) before becoming too sloppy, then I discard the strip for another.

As for synthetic valves, I lay them bottoms-up on a flat surface and gently abrade the area to be glued. I have found that this insures better adhesion than simply applying glue to the slick plastic.

As for trimming, I use a single edge razor blade in a holder, like the type for scraping windows. I use a strip of thin cardboard under the valve tip and adjacent reed (which helps align the end of the reed slot) and zip off the tip of the valve. The cardboard prevents scoring the plate and dulling the blade.

Actually, I'm in the process of doing this right now, if you need a pic or two  (:)

Edited for coherence....
« Last Edit: July 06, 2015, 11:33:45 PM by forrest »
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Installing valves
« Reply #3 on: July 06, 2015, 11:57:55 PM »

Gluing the valves:
I use a clear contact adhesive applied to the valve end straight from the tube of glue. I don't bother with any roughening up of the valve or reed plate surface and I've never had any subsequent problems e.g. valve falling off. If replacing a valve, I do ensure that the reed plate is free of any old glue by carefully picking off any residue with a pair of tweezers. Any particularly tenacious glue residue can usually be removed using a cotton bud moistened with a solvent such as acetone or nail varnish remover.

Trimming a valve to length:
Prior to gluing, I butt up the new valve to the rivet head and offset to one side of the reed plate slot. At the other end of the valve I use a soft pencil to make a small free-hand mark on the valve, about 1 mm beyond the length of the slot (guessed by eye - no need to measure with a ruler). I cut off any surplus length from the valve using sharp paper scissors. Then I glue the valve into place.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Installing valves
« Reply #4 on: July 07, 2015, 05:29:06 AM »

I do pretty much the same as Steve - Bison Universal is readily available here and works well. I often use a scalpel to trim overlength valves, but good quality small sharp scissors are fine.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

KLR

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 640
Re: Installing valves
« Reply #5 on: July 07, 2015, 09:08:24 PM »

Thanks for all the pointers - never thought of using tweezers to get the residual contact cement off...so many of these things seem extra obvious in retrospect.  Actually I was expecting the ultrasonic cleaner to destroy everything in its path, maybe an industrial model would, but that might abrade some metal too.

Will pick up some extra sharp scissors at the embroidery supply house.
Logged

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Installing valves
« Reply #6 on: July 08, 2015, 12:59:29 PM »

I've found medical quality scissors are better....unless you trust yourself with a scalpel    >:E.
Logged
Tuner/repairer, now retired.
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal