Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Tuning Table Construction  (Read 7393 times)

0 Members and 1 Guest are viewing this topic.

Ray Bird

  • Member
  • *
  • Offline Offline
  • Posts: 15
Tuning Table Construction
« on: July 28, 2015, 11:20:20 PM »

My apologies in advance if I have missed a thread on this subject.
I seek information about the appropriate air holes for a basic tuning table. Specifically, the number of holes, square or round, size of holes and centre to centre measurement between holes.
I suspect there is wide variation among different melodeons so I'm looking for the best compromise for a novice.
Ray Bird
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Tuning Table Construction
« Reply #1 on: July 28, 2015, 11:47:36 PM »

I have a couple of tuning bellows of different sizes made from old accordion bellows.

The base is glued to a solid plywood sheet (1) which has a couple of inches overlap all round, so I can clamp the assembly to a bench top. For the top surface I have another plywood sheet (2) with a cut-out about the same size as the accordion bellows interior. The upper surface of sheet 2 is faced with soft chamois leather.  On top of that I have an additional plywood sheet (3), which I can clamp to the top of sheet 2.

Sheet 3 has a single square hole 10mm x 10mm in the centre. This is large enough to admit air into the opening of a single treble reed chamber, either square opening or a round opening e.g. like on Hohners. This is used for tuning reeds when the reed block is removed from the instrument. It's convenient to work on the reeds and reed blocks like this, but see below...

Additionally, I have another plywood sheet (4) the same dimensions as sheet 3, but with a large rectangular opening slightly smaller than, say, a Hohner Pokerwork end cross-section. If you are planning to work on larger instruments, you will need a correspondingly larger opening.  Sheet 4 is faced with chamois leather on the upper surface. The idea of sheet 4 is so that the melodeon (with the bellows removed) can be placed directly on the tuning bellows to sound and work on the reeds in-situ in the instrument. This is important, as the pitch of reeds when the reed block is out of the instrument can be up to 5 cents sharp. The final tuning always needs to be done with the reeds in-situ. 
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Ray Bird

  • Member
  • *
  • Offline Offline
  • Posts: 15
Re: Tuning Table Construction
« Reply #2 on: July 30, 2015, 10:16:23 PM »

Thanks Steve for clarifying a few things for me.
I was concerned that mating a square hole with a round hole might compromise the response and sound of the reed. Because I have a large volume air supply(PA bellows) I will use two 10X10 holes on the table. The physics of air volume and velocity is not my cup of tea and I need to tap the experience of others.
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Tuning Table Construction
« Reply #3 on: July 30, 2015, 10:33:30 PM »

Because I have a large volume air supply(PA bellows) I will use two 10X10 holes on the table.
Why?
One hole is sufficient. You do not need to sound more than one reed at once. If you are trying to check tremolo, that has to be done in the instrument; you can't do it on the tuning table with reed blocks removed from the instrument - the tuning is not accurate enough.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning Table Construction
« Reply #4 on: July 30, 2015, 10:43:50 PM »

I find that it is very useful to have two holes and that tuning the tremolo on a tuning table works very well.  It is important that the holes in the toning table are a fairly close match to the holes in the reed block, and the material of the top of the tuning table should be a similar thickness to the board that the reed block is mounted on in the instrument.  These two things mean that the acoustic behaviour of the region under the reed block is similar with the block in the instrument or on the tuning table.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

brazilian.BOX

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 416
  • youtube search: 8 baixos
Re: Tuning Table Construction
« Reply #5 on: July 30, 2015, 10:45:53 PM »

That's an amazingly great idea! All of us trying our own tuning table. I dream with mine. I can't do it immediately but I will start with it as soon as I have time. But I have an opinion about the instrument, about we should have any initiative even that rudimentary, to make our own tuning of attempts of tunings, even that improvising.

Here, an example and exactly in that "rudimentary" way that I intend to start!  ;D  www.youtube.com/watch?v=NFTOiDcoe-M

I always present for friends here. The title of this video in portuguese you can read, means: accordion tuning, make yourself.
Logged
The Brazilian chromatic tuning: www.youtube.com/watch?v=HwLF1tH3q5Y

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Tuning Table Construction
« Reply #6 on: July 31, 2015, 07:14:28 AM »

Please don't do that, brazilian.Box.  What that clip shows can't be called  tuning.   Vandalism would be a better way to describe it.
« Last Edit: July 31, 2015, 07:20:33 AM by diatonix »
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Tuning Table Construction
« Reply #7 on: July 31, 2015, 08:21:51 AM »

Here, an example and exactly in that "rudimentary" way that I intend to start!  ;D  www.youtube.com/watch?v=NFTOiDcoe-M

I always present for friends here. The title of this video in portuguese you can read, means: accordion tuning, make yourself.

Please don't do that, brazilian.Box.  What that clip shows can't be called  tuning.   Vandalism would be a better way to describe it.

Agreed - this is not good practice.

We've had threads before on the forum about using a dremel tool for tuning. They are too harsh, a slip can mean removing too much steel in one go and/or damaging the sides of the reed plate slot. The frictional heat generated can seriously affect the temper of the steel, and there is the added risk of the rotating tool catching and distorting the tip of the thinner reeds. Also the dremel is distractingly noisy and takes a while to run up to speed. It's far better to use proper hand-tools such as precision files and reed-scratchers and learning how to use them. 

Other issues with this video:

1. Using this set-up, it looks as if the operator is attempting to tune the reeds to pitch on the tuning table. As has been mentioned before, when the reed block is out of the instrument the reeds will sound at a different pitch, usually noticeably sharp, from when in place in the instrument. If you are going to use a tuning table in this way you have to allow for this by measuring the pitch of each reed in the instrument (Pi) first of all and then again on the tuning table (Pt). If (Pi) is, for example, 3 cents flat of true pitch, then that is the amount which (Pt) needs to be raised to get it to true pitch. This is 'tuning by offsets'.

If the measuring and filing is done carefully, tuning by offsets should get you close to your target pitch once the reeds are back in the instrument. But even then, some minor adjustments will almost certainly still need to be made in-situ in the instrument.

2. The pitch of a reed sounded in a reed block as shown in the video will also vary according to how rigidly the reed block is held on the surface of the table. Just laying the reed block loosely over the hole in the table top is not going to give you consistent results. Ideally, some sort of clamping device needs to be used to hold the reed block firmly and consistently in place, just as it is held inside the instrument. A hand placed firmly on top of the reed block usually works quite well, but you have to be careful that your palm or fingers are not too close to the ends of the reed plate being sounded, otherwise this can flatten the pitch due to some sort of 'end effect' and will result in erroneous measurements.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

blue eyed sailor

  • Melodeon renegade - partly reverted - Preciosa maniac
  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 264
  • since folk process is running, take an active part
    • My Sound Cloud
Re: Tuning Table Construction
« Reply #8 on: July 31, 2015, 10:58:49 AM »

Steve, some appreciated information, notably regarding "tuning by offsets", which sounds very practicable...; thank you for that!

Don't want to hijack the thread, just a short question I'm having in my mind for some weeks now: Could there - for minor corrections in situ - be a thing like "tuning by adjusting valves" (which I would like to apply to one or two pull reeds, being somewhat reluctant to de-waxing the reed plate, by covering either a larger or a smaller amount of the reed slot)?

Best wishes - Wolf
Logged
Hohners: 2x Preciosa Bb/Eb (tremolo / light swing) - Club IV Bb/Eb - Morino Club C/F
Presswood C/F - Pokerwork C - Verdi II (PA) - Lucia IV (PA) - Starlet (PA)

Weltmeister 509 G/C/F - Juwel (PA) -- Horch C/F (12 bass) -- Cantulia Bambi 26 (PA)
and: Castagnari Giordy G/C

be warned of my SC page, mainly concertina thus far

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Tuning Table Construction
« Reply #9 on: July 31, 2015, 11:29:58 AM »

If it is a normal size reed with no issues, why de-wax?
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Tuning Table Construction
« Reply #10 on: July 31, 2015, 11:46:42 AM »

Don't want to hijack the thread, just a short question I'm having in my mind for some weeks now: Could there - for minor corrections in situ - be a thing like "tuning by adjusting valves" (which I would like to apply to one or two pull reeds, being somewhat reluctant to de-waxing the reed plate, by covering either a larger or a smaller amount of the reed slot)?
Valves do indeed affect the pitch of a reed. A heavier or thicker valve will tend to flatten the pitch of its associated reed tongue. Similarly the length of the glued section of the valve can govern how much the valve lifts away from the reed plate which in turn affects the pitch. A valve which doesn't lift far enough will flatten the pitch of a reed tongue and can also result in a muted, quieter sound.

However, I would say it is almost impossible to quantify these effects to predict the magnitude of such a pitch change, and anyway, it shouldn't be necessary to do this. It is perfectly possible to fine-tune the pull reed tongues without removing the reed plate from the wax. A pull reed can be flattened by carefully scratching the belly of the reed by using a reed scratcher through the reed-plate slot. The scratcher is inserted beneath the valve, gently lifting it slightly. 

To sharpen a pull reed is slightly more tricky - you will need a reed-lifter tool, either the hook-shaped Italian style, or the thin pointed brass Hohner-style tool. The reed-lifter is used to raise the reed tongue gently through the slot in the reed plate. Then a reed steady or thin shim is inserted under the tip to support the reed tongue for careful filing.

It's much easier to see this process in action than to try and describe it. Theo used to have a set of photos illustrating the process, but I don't have the link right now. I'm sure someone will oblige...

As a final comment, the only time I would remove the reed plate from the wax for tuning the pull reeds would be for the very highest tiny piccolo reeds of a 'H' voice e.g. on a four-stop LMMH instrument. These reeds are very delicate and attempting to pull the reed tongue through the slot would most likely result in damage.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning Table Construction
« Reply #11 on: July 31, 2015, 11:50:04 AM »

Steve, some appreciated information, notably regarding "tuning by offsets", which sounds very practicable...; thank you for that!

Don't want to hijack the thread, just a short question I'm having in my mind for some weeks now: Could there - for minor corrections in situ - be a thing like "tuning by adjusting valves" (which I would like to apply to one or two pull reeds, being somewhat reluctant to de-waxing the reed plate, by covering either a larger or a smaller amount of the reed slot)?

Best wishes - Wolf

A correctly valved reed has the minimum of restriction imposed on the air flow by the valve.  Anything that restricts the air flow will tend to flatten the pitch, but will also prevent the reed from reaching its full volume, so tuning by using heavier vales will also deaden the sound.  Not a good idea.
As Diatonix says why do you want to de-wax the reed?  The final tuning needs to be done with the reed waxed onto the block, so there is no gain.  If you want to tune then learn the skills, but don't do it on your Preciosa. Buy a junk box to learn on, then try tuning for real on a box with conventional reed blocks, and then have a good think before trying to tune a Preciosa.  Preciosa reeds are smaller and thinner than standard reeds, and the design of the box makes access to the reeds more difficult.  I have seen too many unfortunate Preciosa reeds that have been wrecked by unskilled attempts at tuning. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

blue eyed sailor

  • Melodeon renegade - partly reverted - Preciosa maniac
  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 264
  • since folk process is running, take an active part
    • My Sound Cloud
Re: Tuning Table Construction
« Reply #12 on: July 31, 2015, 12:11:35 PM »

Theo, I'm very reluctant to damage the reeds of the Preciosa, hence the question raised - but I learned the basic skills trough tuning several melodeons over the years, and did some minor tuning to my EC too...

Best wishes - Wolf
Logged
Hohners: 2x Preciosa Bb/Eb (tremolo / light swing) - Club IV Bb/Eb - Morino Club C/F
Presswood C/F - Pokerwork C - Verdi II (PA) - Lucia IV (PA) - Starlet (PA)

Weltmeister 509 G/C/F - Juwel (PA) -- Horch C/F (12 bass) -- Cantulia Bambi 26 (PA)
and: Castagnari Giordy G/C

be warned of my SC page, mainly concertina thus far

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning Table Construction
« Reply #13 on: July 31, 2015, 12:31:35 PM »

So if you are an experienced tuner why would you want to mess about with using valves for tuning?
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

blue eyed sailor

  • Melodeon renegade - partly reverted - Preciosa maniac
  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 264
  • since folk process is running, take an active part
    • My Sound Cloud
Re: Tuning Table Construction
« Reply #14 on: July 31, 2015, 01:15:25 PM »

So if you are an experienced tuner why would you want to mess about with using valves for tuning?

...as said, because I don't want do de-wax reedplates at the moment, which would be inevitable for tuning a pull reed of the Preciosa AFAICS...

Second issue, I'm undecided whether to bring (or have brought) the instrument up to A=440 hz or leave it at 435; in this case I might end up with re-sharpening a reed which I priorly had brought some cents down; and it's exactly this kind of thing which I really want to avoid.
Logged
Hohners: 2x Preciosa Bb/Eb (tremolo / light swing) - Club IV Bb/Eb - Morino Club C/F
Presswood C/F - Pokerwork C - Verdi II (PA) - Lucia IV (PA) - Starlet (PA)

Weltmeister 509 G/C/F - Juwel (PA) -- Horch C/F (12 bass) -- Cantulia Bambi 26 (PA)
and: Castagnari Giordy G/C

be warned of my SC page, mainly concertina thus far

blue eyed sailor

  • Melodeon renegade - partly reverted - Preciosa maniac
  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 264
  • since folk process is running, take an active part
    • My Sound Cloud
Re: Tuning Table Construction
« Reply #15 on: July 31, 2015, 01:47:44 PM »

To sharpen a pull reed is slightly more tricky - you will need a reed-lifter tool, either the hook-shaped Italian style, or the thin pointed brass Hohner-style tool. The reed-lifter is used to raise the reed tongue gently through the slot in the reed plate. Then a reed steady or thin shim is inserted under the tip to support the reed tongue for careful filing.

That's new information for me, Steve - thank you for that! I was wondering whether it could be done like this but came to the - apparently wrongful - conclusion that it wouldn't work...

(second paragraph removed, as I was sort of torn between the various replies)

Now adding: as to a reed scratcher, there seem to be different, well, cultures of tuning in a melodeon/accordion and a concertina world. I reckon it would never be recommended to scratch a concertina reed. OTOH, they're all so easily accessible...

I'll have to think this over - my apologies for having been too hasty here!

Best wishes - Wolf
« Last Edit: July 31, 2015, 02:29:44 PM by blue eyed sailor »
Logged
Hohners: 2x Preciosa Bb/Eb (tremolo / light swing) - Club IV Bb/Eb - Morino Club C/F
Presswood C/F - Pokerwork C - Verdi II (PA) - Lucia IV (PA) - Starlet (PA)

Weltmeister 509 G/C/F - Juwel (PA) -- Horch C/F (12 bass) -- Cantulia Bambi 26 (PA)
and: Castagnari Giordy G/C

be warned of my SC page, mainly concertina thus far

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning Table Construction
« Reply #16 on: July 31, 2015, 02:07:27 PM »

If you are unfamiliar with the techniques fir tuning pull reeds in situ you really should take your Preciosa to an experienced tuner to do the work.  It is basic tuning technique.  It is also more difficult on a Preciosa than almost any other box because if the restricted space you have to work in.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

brazilian.BOX

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 416
  • youtube search: 8 baixos
Re: Tuning Table Construction
« Reply #17 on: July 31, 2015, 02:14:52 PM »

Please don't do that, brazilian.Box.  What that clip shows can't be called  tuning.   Vandalism would be a better way to describe it.

LOL!!!  ;D ;D ;D

Man, it's an starting! A way to have your very 1st contact with the tuning like playing as a child with the tuning. After, for sure would come improvements and better equipment!  :D
Logged
The Brazilian chromatic tuning: www.youtube.com/watch?v=HwLF1tH3q5Y

blue eyed sailor

  • Melodeon renegade - partly reverted - Preciosa maniac
  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 264
  • since folk process is running, take an active part
    • My Sound Cloud
Re: Tuning Table Construction
« Reply #18 on: July 31, 2015, 02:17:57 PM »

If you are unfamiliar with the techniques fir tuning pull reeds in situ you really should take your Preciosa to an experienced tuner to do the work.  It is basic tuning technique.  It is also more difficult on a Preciosa than almost any other box because if the restricted space you have to work in.

O.k., thank you!
Logged
Hohners: 2x Preciosa Bb/Eb (tremolo / light swing) - Club IV Bb/Eb - Morino Club C/F
Presswood C/F - Pokerwork C - Verdi II (PA) - Lucia IV (PA) - Starlet (PA)

Weltmeister 509 G/C/F - Juwel (PA) -- Horch C/F (12 bass) -- Cantulia Bambi 26 (PA)
and: Castagnari Giordy G/C

be warned of my SC page, mainly concertina thus far

brazilian.BOX

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 416
  • youtube search: 8 baixos
Re: Tuning Table Construction
« Reply #19 on: July 31, 2015, 02:19:22 PM »

Uuaahahauahahahaha  ;D ;D

I am still laughing about reaction of the people with the example of "my 1st tuning table". I told it was "rudimentary"
And what this word can show you? For me "rudimentary" send immediately to something like in the times of the caves, so the improvisation is evident and explicit.  ;)


HU HU HU
UGA - BUGA!!!   ;D
Logged
The Brazilian chromatic tuning: www.youtube.com/watch?v=HwLF1tH3q5Y
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal