Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Spot waxing  (Read 2690 times)

0 Members and 1 Guest are viewing this topic.

KLR

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 640
Spot waxing
« on: July 31, 2015, 06:31:57 PM »

I've always used the soldering iron and stick of wax method, sometimes with messy results; watching Lester's video on YT I notice his stick is a lot smaller than what I have, perhaps that's why sometimes I have rogue blobs dripping here and there?  Reed Waxing - The Lester Method
by Lester Bailey.
  But even an old hand like Les has a big ol' dribble of wax headed down the side of the block at one point.  Maybe let's chalk that up to camera nerves.

The other night another approach occurred to me - cut some wax off the block and stick in place, ready to use.  Tried it on a whole row yesterday - much cleaner results, just the minimum of wax in place too, no honkin' big blobs at the bottom of the block.  One thing I quite like about this approach is that I can old the block in the left hand and have the iron in the right, and hold it up very close to the eyes - important as I have a bad case of presbyopia and need to see things up close without my glasses.  This way you can see any gaps in the block too - I noticed a few chipped out spots where the wax could possibly seep through to the back, and was able to make sure the wax wasn't hot enough in that spot to make it through the crack.

Reviewing more vids of waxing I noticed I'd forgot about Charlie Marshall using a paint brush.  That would work great, very lightweight of course.  This fellow uses a syringe:  accordion renovation for beginners: low-skill waxing method - YouTube  We should have a race, see which method gets the job done the fastest.  Wax pots with spoons/brushes/syringes can be deployed pretty fast, but you have to wait for the wax to melt, so...my approach might be of use to others who are also having trouble with messes.
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Spot waxing
« Reply #1 on: July 31, 2015, 06:55:07 PM »

I would take care waxing very close to my face as the fumes are fairly horrid if not exactly dangerous.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Spot waxing
« Reply #2 on: July 31, 2015, 06:55:42 PM »

Seconded.  Gave me asthma.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

KLR

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 640
Re: Spot waxing
« Reply #3 on: July 31, 2015, 07:56:50 PM »

Is that what the splatter guard on your iron is for, Lester?  Or is that a thumb hold.

I haven't noticed any ill effects from molten wax in my couple years of doing so.  Fields of new mown hay or buffing corrosion off sheet metal did me in recently, but wax is next to innocuous.  Maybe if I worked on boxes for a living I'd be concerned.  Also, if anything this approach directs fewer fumes towards my nose, come to think of it.  I'm not hunched over the block itself trying to see what's going on, it's not like I've got my proboscis jammed against the reeds or something here.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Spot waxing
« Reply #4 on: July 31, 2015, 08:02:38 PM »

but wax is next to innocuous. 


Wax may be innocous, but fumes from rosin is one of the biggest industrial causes of asthma, particularly in electronics where it is used as a soldering flux.  It does take a while to become sensitised, but once it happens you are stuck with it.  Best to be on the safe side and avoid inhaling any fumes.

Just Google colophony occupational asthma for details.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Spot waxing
« Reply #5 on: July 31, 2015, 08:12:48 PM »

Is that what the splatter guard on your iron is for, Lester?  Or is that a thumb hold.

It's neither, it's just a hook for hanging it up with.

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Spot waxing
« Reply #6 on: August 01, 2015, 03:03:55 PM »

All my waxing is done in a specially constructed bench-top booth with extractor fan and electric light. Before installing the booth my apprentice tuner and I were both suffering some respiratory problems after a day's waxing.

I've been using a soldering iron for years but am currently studying the wax pot and spoon method as used by the big boys and girls. I'm currently experiencing limited success but I'll surely get the hang of it.

Here's a great video by diatonix of this parish showing exactly how it should be done: https://www.youtube.com/watch?v=yjGaLwqrtOs
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

KLR

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 640
Re: Spot waxing
« Reply #7 on: August 01, 2015, 08:11:12 PM »

Wouldn't a small fan on a stand blowing behind you make this whole matter of fumes a non-issue?  I'm not going to be waxing stuff all day myself - were you working in Kligenthal or something?  I only work on boxes as a hobby so about 20 minutes of fumes for me, tops.

Do you guys use a mechanical 3rd hand to hold the block, too?  I always just tipped the block onto a bit of scrap wood with a slant in its side, and am still using that for the initial waxing of the top/bottom, to get the reeds to sit still.  Works but there are more stable approaches.
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Spot waxing
« Reply #8 on: August 01, 2015, 09:53:27 PM »

I build and repair accordions for a living so much time is spent waxing. My tuning room is fairly small so fumes must be extracted to the outside air. A fan would just move them about.
I've tried using a swivel vice to hold the reedblock but generally prefer to rest it on a block of wood.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Spot waxing
« Reply #9 on: August 01, 2015, 09:54:14 PM »


Do you guys use a mechanical 3rd hand to hold the block, too?  I always just tipped the block onto a bit of scrap wood with a slant in its side, and am still using that for the initial waxing of the top/bottom, to get the reeds to sit still.  Works but there are more stable approaches.

I use an old "bucky" neck pillow, soft fabric with a loose fill of buckwheat hulls.....a sort of mini-bean bag. It allows positioning in many angles, sometimes I also employ a long skinny rubber band to help it stay in position. I would think a canvas or thin leather sack containing sand or steel shot would be better, just for the ballast
« Last Edit: August 02, 2015, 05:55:54 AM by forrest »
Logged

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Spot waxing
« Reply #10 on: August 02, 2015, 11:45:48 PM »

Here's a great video by diatonix of this parish showing exactly how it should be done: https://www.youtube.com/watch?v=yjGaLwqrtOs

I've not seen a "spoon" like that before.  Could you tell us where it came from?
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Spot waxing
« Reply #11 on: August 03, 2015, 12:43:39 AM »

I watched that video umpteen times and have made a spoon just like it from a sheet of thin brass. I made a cardboard template first to get the shape right, then cut out the brass with snips, then soldered it together and added a handle. Mine is made from a single piece of brass. The width of the slot where the wax runs out is important and determined through trial and error. Also I've found that the wax needs to be properly hot to flow nicely. You won't want to mess around with a soldering iron or paint brush or even a flat spoon once you get the hang of using this tool. But it does take an awful lot of practice and a steady hand.

syale

  • The Terrier
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
  • When will this MADness stop?
Re: Spot waxing
« Reply #12 on: August 03, 2015, 03:36:36 AM »

Waxing spoon available on ebay
Logged
HA114 C/G/A/D, 2915 G/C. Liliput, Club IIB C/F Dino Baffetti Modell 22 B Twitter: @syale

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Spot waxing
« Reply #13 on: August 03, 2015, 07:09:46 AM »

Having watched Olav's video a couple of times, I think the design and principle is superb, much better than the old flat-tin-spoon-on-a-stick that I bought from Ernest Deffner years back, in fact it reminds me a bit of a draftman's ruling pen, which I used to use back when working drawings were done on coated linen sheets with India ink. (Pre-Cad). The one listed on eBay looks slightly different that the one Olav is using, maybe a bit trimmer.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Spot waxing
« Reply #14 on: August 03, 2015, 08:50:02 AM »

The main difference is the angle of the handle. i haven't tried the straight handled one but Olaf's design does mean the spoon sits nicely in the wax pot. And the spoon cost me virtually nothing to make.

Prestidigitator

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 448
  • Saltarelle, Hohner, Oakwood Baffetti
Re: Spot waxing
« Reply #15 on: August 03, 2015, 10:07:05 AM »

The main difference is the angle of the handle. i haven't tried the straight handled one but Olaf's design does mean the spoon sits nicely in the wax pot. And the spoon cost me virtually nothing to make.

After seeing Olaf's video, and a bit of correspondence with him, I made several of these in the same fashion as yours i.e. with brass sheet and tube, plus wooden handles. I did experiment with the angle of the handles, both fore and aft, but the one I found easiest to use was where the handle, looking at the spoon from the wider handle end, was offset about 40 degrees from the vertical (see photo).

The other thing that took some trial and error was getting the gap at the "business end" right to suit the wax and the rate of flow needed, but that's not too difficult with brass sheet and a decent pair of tinsnips.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal