Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Another Reed Waxing Thread  (Read 5711 times)

0 Members and 1 Guest are viewing this topic.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Another Reed Waxing Thread
« on: July 31, 2015, 06:54:05 PM »

I noted in KLR's thread that he referred to 'just the minimum of wax'. This triggered a thought; when I wax I am reasonably sparing with the wax and this seems OK to me. But I have also have had, only this week, a box in the workshop that the fabled Nils Nielsen had worked on. Now it is really easy to spot his waxing as he used very green wax from his own 'secret recipe' but, and more to the point of this thread, he uses lots of wax, much more than I would use.

So the question is does it matter how much wax you use to fit reeds? Doesn't seem to to my way of thinking but Nils was infinitely more knowledgable than me so now I'm not sure.

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Another Reed Waxing Thread
« Reply #1 on: July 31, 2015, 10:45:31 PM »

I noted in KLR's thread that he referred to 'just the minimum of wax'. This triggered a thought; when I wax I am reasonably sparing with the wax and this seems OK to me. But I have also have had, only this week, a box in the workshop that the fabled Nils Nielsen had worked on. Now it is really easy to spot his waxing as he used very green wax from his own 'secret recipe' but, and more to the point of this thread, he uses lots of wax, much more than I would use.

So the question is does it matter how much wax you use to fit reeds? Doesn't seem to to my way of thinking but Nils was infinitely more knowledgable than me so now I'm not sure.

Good topic, Lester. I am much interested in hearing replies. As for myself, I often initially 'tack' the reeds to the block on the heel and toe ends with a very light touch of wax, then test the reeds a bit to be certain all the inside valves are clear and not rubbing, and that they are secure. This makes it easy to pop a reedplate off the block to remedy any small glitches before the full-on waxing.  Now and then, I do have to pull a reed plate to make an adjustment. The reeds are usually stuck down pretty well with even that small amount of wax so that I use a dull blade to score and pry the plate off. After any adjustments are made, I go ahead and wax the plates thoroughly. Seems that one does not need a thick bed of wax around the plates to hold them securely. If there is some advantage as to tone or resonance, who knows? But I have never had a reed plate fall off. I have seen the paintbrush method, and it seems tedious.
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Another Reed Waxing Thread
« Reply #2 on: July 31, 2015, 11:06:24 PM »

Good topic, Lester. I am much interested in hearing replies. As for myself, I often initially 'tack' the reeds to the block on the heel and toe ends with a very light touch of wax, then test the reeds a bit to be certain all the inside valves are clear and not rubbing, and that they are secure. This makes it easy to pop a reedplate off the block to remedy any small glitches before the full-on waxing.  Now and then, I do have to pull a reed plate to make an adjustment. The reeds are usually stuck down pretty well with even that small amount of wax so that I use a dull blade to score and pry the plate off. After any adjustments are made, I go ahead and wax the plates thoroughly. Seems that one does not need a thick bed of wax around the plates to hold them securely. If there is some advantage as to tone or resonance, who knows? But I have never had a reed plate fall off. I have seen the paintbrush method, and it seems tedious.

You seem to work in much the same way as I do.

As to the paint brush method I do use it but only on Hohner 1 Rows on the inside reed pairs as the way they  sit makes it  virtually impossible to get a soldering iron in to the space with out dripping wax or melting valves.

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Another Reed Waxing Thread
« Reply #3 on: August 01, 2015, 03:41:34 AM »

Here's something which I found a bit daunting...I had been wanting to re-valve and re-wax the Pistelli, as it has probably never been done on this instrument in its' 50+years. However, it appeared that the reed blocks were waxed in, and I was reluctant to start and postponed the task for several years. Recently, I mustered the time and energy to do it., only to find out that the reed blocks were not waxed in, but rather glued solidly in place. That situation, and the fact that the blocks are slanted away from the center (where the low-voice block lives, which IS removable) put me into a real ordeal. I had to somehow remove the reeds from the blocks in situ,  scrape and clean the old wax and prep for the new, not to mention devise some impromptu special tools. I have posted two pics, one shows the amount of space in which I was working, and the other shows my waxing iron with a special extended and narrow tip to reach in and apply the new wax. Lotsa fun  :D. All that's left to do is the center block with the low reeds, which is a walk in the park.
« Last Edit: August 01, 2015, 04:00:08 AM by forrest »
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Another Reed Waxing Thread
« Reply #4 on: August 01, 2015, 07:46:31 AM »

Here's something which I found a bit daunting...I had been wanting to re-valve and re-wax the Pistelli, as it has probably never been done on this instrument in its' 50+years....

I think you have taken on a real challenge and done a superb job of it!  (:)

Presumably the original waxing was carried out before the reed blocks were glued into position. I do wonder about the philosophy of gluing reed blocks in position in the first place. I understand that some makers believe the sound is better/louder, but what is in their minds when, or if, they contemplate repair or maintenance work at a later date? OK - the original wax might last a good few decades before it needs replacing and might outlast the anticipated life of the instrument. But what about instances of replacing an inside valve which has come adrift (it happens!) or those tricky tuning jobs on the tiniest reeds where you daren't use a reed lifter?

I have always argued that in any construction project, whether musical instruments, aircraft or suspension bridges, it is essential to design-in access for future maintenance, repair and replacement.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Another Reed Waxing Thread
« Reply #5 on: August 01, 2015, 11:35:35 AM »

We (or I, at least...) do not believe that the sound has a significantly higher dynamic potential with the reedblocks glued straight on to the faceboard, we know that as a fact.

Waxing is absolutely no problem, at least if one has become familiar with some of the far better suited tools than the usual soldering iron or brush, and adopts the methods used in most professional accordion manufacturing environments.

Neither is tuning an issue. A skilled tuner is able to lift any pull reed in, say, a CF melodeon without thinking twice. I agree that some of the smallest piccolo reeds can be tricky, but they are not at all common in diatonic instruments. And even in larger chromatic ones with removable blocks many tuners will opt to take them out of their wax bed in order to deal with them.

As to maintenance, I cannot see any problems other than the possible difficulty  in some geographical areas to find a skilled technician, but that's another issue. And to change the occasional valve is certainly no bigger a challenge than with any other instrument.
« Last Edit: August 01, 2015, 05:30:33 PM by diatonix »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Another Reed Waxing Thread
« Reply #6 on: August 01, 2015, 11:41:45 AM »

I have posted two pics, one shows the amount of space in which I was working,

That looks like wide open spaces compared with the facing sides of glued in blocks on a Hohner 114.  But there are ways of overcoming every problem.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Another Reed Waxing Thread
« Reply #7 on: August 01, 2015, 04:28:03 PM »

I have posted two pics, one shows the amount of space in which I was working,

That looks like wide open spaces compared with the facing sides of glued in blocks on a Hohner 114.  But there are ways of overcoming every problem.

There are. It's purely a matter of time and patience. As diatonix mentioned, the spoon seems to work well for fast production work, especially if there is plenty of open territory in which to operate. My difficulty with the spoon was that one must maintain a large enough quantity of molten wax for dipping the spoon, which in turn leads to the fume situation, and also one needs a way to regulate the heat of the wax accurately to avoid losing the essential resins that give the wax longevity. Also, when finished, does one discard the remaining wax which has been sitting there cooking all the while?
  In my case, I can use the iron (which I can control themostatically), do a few or a lot of reeds, and then put the task away with little fuss, and get decent controllable results. Were I  regularly doing many reeds or blocks at a sitting, I would probably follow the spoon/pot method.
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Another Reed Waxing Thread
« Reply #8 on: August 01, 2015, 05:17:26 PM »

I use a relatively small wax heater, originally designed for cosmetic purposes, with a heat regulator. Even when in some cases I have to melt more wax than I actually need, its quality will not be affected in a noticeable way. Fumes are not a big problem either, at least if  compared with a soldering  iron where you get the smoke right up your nostrils. As to the admittedly very important issue of longevity: I'm convinced that a hot soldering iron does more damage to the wax than a good wax heater with a thermostate.
Logged

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Another Reed Waxing Thread
« Reply #9 on: August 01, 2015, 06:28:09 PM »

I can dial he heat of the iron to a degree where the wax does not smoke. I am not denying the value of the wax pot, only stating that the alternative seems to work well for me, as my waxing projects are relatively small, and infrequent.  ;)  Also, in the above photo, the space between the cabinet and reed block prohibited the use of my standard iron tip, which is 12mm wide. There was no room to manipulate it in the space without possible damage to valves. The tip I made was 7mm wide. The time interval of introducing the tool into the correct position would have allowed the wax to cool on a regular spoon. The iron maintained the heat to allow delivery of liquid wax after careful positioning. Anyway, it's done and I am glad. Someone 30 years from now can worry about it!  ;D
« Last Edit: August 01, 2015, 06:42:50 PM by forrest »
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Another Reed Waxing Thread
« Reply #10 on: August 05, 2015, 01:38:28 PM »

I know it has undoubtedly already been covered elsewhere, but I've just spent over an hour using the search facility to no avail...

I have a fine-tipped 18W soldering iron and some wax sticks from Charlie Marshall and half a mind to attempt possibly the most difficult job - rewaxing the upper treble block on a Preciosa!  Some time back I had a "printer's pie" explosion of reeds from the centre of the block.  Will I need a controller to reduce the heat of the iron, or will a minimal application do no damage to the wax composition?

Rob.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Another Reed Waxing Thread
« Reply #11 on: August 05, 2015, 02:10:09 PM »

My view is that a thermostatically controlled soldering iron is essential for waxing, if a soldering iron is your preferred tool. A dimmer or other voltage control is a poor substitute because it still delivers a constant amount of heat to the iron so there is still the likelihood of overheating while the iron is not melting wax. An iron with a stat adjusts the heat input so that the temperature remains more or less constant to balance the changes in heat used when the iron goes from waiting to melting wax.

This is especially true for a Preciosa where the space for wax is minute.  It is also essential to remove all the old wax first.  If you don't then its just about impossible to get the reed plates to make good contact with the wood which is important for secure fixing of reed plates.

 Thermostatic irons are not expensive.  Your Preciosa is.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Another Reed Waxing Thread
« Reply #12 on: August 05, 2015, 02:21:12 PM »

I have a fine-tipped 18W soldering iron and some wax sticks from Charlie Marshall and half a mind to attempt possibly the most difficult job - rewaxing the upper treble block on a Preciosa!  ... Will I need a controller to reduce the heat of the iron, or will a minimal application do no damage to the wax composition?
As Theo says, you will need a temperature controller of some sort. Uncontrolled soldering irons reach too high a temperature which will cause the wax to rapidly darken and smoulder.

Thermostatically controlled soldering irons are not that expensive. I got mine from Maplin, a bit like this:
http://www.maplin.co.uk/p/maplin-50w-solder-station-n78ar

This particular model has a temperature setting range of of 180°C to 480°C. I find that a suitable temperature setting for wax sticks is about 190° - 210° C, depending on the composition of the wax.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Another Reed Waxing Thread
« Reply #13 on: August 05, 2015, 03:33:41 PM »

Thanks guys, your points taken on board - have to wait to next payday, then.  No real prospect of success first time, but I need to try!  Nerves are getting the better of me.  I spect loads of time checking the layout of the buttons and linkages, the Club layouts on the website, etc and mapping what I expect to find. Then I realised that the upper reed pan is just the same as the lower ones, so all I have to do to get the reeds in the right place is to ping them and match the existing ones.  Next step, then is to get the used wax cleaned off and do a dry assembly run.  If I bottle out after that, nothing lost.

Rob.
Logged

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Another Reed Waxing Thread
« Reply #14 on: August 05, 2015, 05:11:56 PM »


As Theo says, you will need a temperature controller of some sort. Uncontrolled soldering irons reach too high a temperature which will cause the wax to rapidly darken and smoulder.

Yes indeed....and I would add that the tip of the iron works better if it is modified into a flatter 'butterknife' shape, rather than a round shaft with a point. This gives more surface area for the liquid wax to load, and allows more precise placement. I replaced my tip with a length of #6 solid copper wire, which I hammered out (after annealing) and then shaped with a rotary sanding tool.
« Last Edit: August 05, 2015, 05:14:03 PM by forrest »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Another Reed Waxing Thread
« Reply #15 on: August 05, 2015, 05:35:25 PM »

I find the opposite works for me.  A fairly fine point with a smooth tip.  But I don't try to load the tool.  I let the wax run down the shaft to the tip where it runs off in an easily controlled bead.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

KLR

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 640
Re: Another Reed Waxing Thread
« Reply #16 on: August 05, 2015, 08:47:48 PM »

Here's another question:  how do you fellows go about cleaning up the soldering iron?  Assuming you bother, mine is always getting encrusted in brownish schmutz that colors the wax brown if something isn't done, so I've been scouring mine with fine steel wool every now and then. 
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Another Reed Waxing Thread
« Reply #17 on: August 05, 2015, 08:50:13 PM »

That should not happen, either the rosin in you was is not completely dissolved, of the iron is too hot. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Another Reed Waxing Thread
« Reply #18 on: August 05, 2015, 08:51:58 PM »

Here's another question:  how do you fellows go about cleaning up the soldering iron?  Assuming you bother, mine is always getting encrusted in brownish schmutz that colors the wax brown if something isn't done, so I've been scouring mine with fine steel wool every now and then.
I let the iron cool down just a little bit and then wipe the tip by puling it through between a couple of wads of damp paper towels. If you get a lot of brown residue ont soldering iron tip, it's possible you have the temperature setting a bit too high. Try reducing the heat a bit.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Another Reed Waxing Thread
« Reply #19 on: September 28, 2015, 06:41:25 PM »

Let's hope it's not too early to talk of success - Preciosa is back up and shouting!  One whole evening spent cleaning and scraping all the bits.  One whole evening blowing and sucking to get the reeds in the right order.  One whole evening waxing - slowly and nervously.

Glad to say, my little soldering iron doesn't seem to have the guts to burn the wax and if the stick was applied to the very tip it made a very small fillet - lovely!  I've given the box a couple of thrashings and nothing has fallen off... yet.

Next thing to try is tuning - far more appealing than retaping bellows!

Rob.
Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal