Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Lighter springs on Panther?  (Read 1033 times)

0 Members and 1 Guest are viewing this topic.

dtuite

  • Member
  • *
  • Offline Offline
  • Posts: 7
Lighter springs on Panther?
« on: September 12, 2015, 02:04:09 AM »

I tried to search for this topic; forgive me if I missed an earlier thread.  In brief, can I easily Replace the bass and treble springs on a Panther with lighter ones?

The Panther, a G C F, is stock.  Most of the time,  I  prefer to play on  mywonderful, pre-unification, Weltmeister G C Pokerwork, but sometimes, it would be nice to play on the Hohner, which is a whole lot drier.

But the Panther springs, compared to those on the Weltmeister, are very much stiffer. It's  a bit llike switching between a pennywhistle and a tuba. Does Hohner sell lighter springs, and if they do, does it take an advanced mechanic to replace them?
Logged

dtuite

  • Member
  • *
  • Offline Offline
  • Posts: 7
Re: Lighter springs on Panther?
« Reply #1 on: September 12, 2015, 02:09:26 AM »

Okay.  How did I miss mselec's thread, which is right below this?  Is that the answer?  Is a 3arow always going to be heavier on the buttons than  2?
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Lighter springs on Panther?
« Reply #2 on: September 12, 2015, 04:20:06 AM »

From what I understand, it's not the number of rows that make a difference, but rather the number of reeds that would be playing at one time.  On a one-row, four-stop box, you potentially have four sets of reeds being played at one time, which means 4 holes per pallet and a lot more air pushing up against it...this would necessitate stronger springs than on something like an Erica or Pokerwork which only has two sets of reeds and therefore only two holes per pallet.  I believe a Panther only has two sets of reeds as well.  The fact that it has three rows shouldn't make a difference, as far as I understand.
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Lighter springs on Panther?
« Reply #3 on: September 12, 2015, 09:06:01 AM »

Useful things to know:
Springs can be adjusted to make them softer by bending the legs.  Proceed with care or you could end up with broken springs, or springs that are uneven in pressure, or are too soft.
Hohner sell springs in different thicknesses going in0.5mm steps.  Standard on two row are 0.5 on the inside row and 0.55 on the outside row. The panther may use three different weights of spring. Your first step is to measure the thickness of the springs. You will need a micrometer or a digital caliber and you might need to remove a spring to get an accurate measurement.
To replace springs you have to remove all of the mechanism from the instrument.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

dtuite

  • Member
  • *
  • Offline Offline
  • Posts: 7
Re: Lighter springs on Panther?
« Reply #4 on: September 12, 2015, 05:01:35 PM »

Thanks.  That clarifies the possibilities . . And the disincentives.  I could screw up a perfectly decent instrument .  Maybe I should just spend some more adapting to the instrument, instead of the other way around.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal