Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Wax embrittlement/tiny gaps  (Read 2709 times)

0 Members and 1 Guest are viewing this topic.

KLR

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 640
Wax embrittlement/tiny gaps
« on: September 15, 2015, 05:06:06 AM »

George Bachich warns:

Quote
        When you need to wax but the job is too small to justify firing up your wax pot, use a modified 15 watt soldering iron. Bigger irons produce too much heat and will cause your wax to smoke, driving off volatile compounds and causing premature aging and embrittlement of the wax. Even a 15 watt iron produces too much heat unless you modify the tip to dissipate it.

        Make a heat sink/waxing tip from a piece of copper flashing and rivet it to your soldering tip. Longer soldering tips are better because they allow more secure mounting of the heat sink. The heat sink should be approximately 3/4 inch wide by 1 1/4 inch long.

Anybody using soldering irons run into this issue?  Doesn't sound like it.  Certainly things can go wrong with wax, even on ostensibly top of the line instruments.  The wax in my Club Morino falls apart upon handling, as I was reminded the other night when I was fixing up a couple of silent reeds who'd stopped speaking when too many wax particles had fallen onto the tongues, and you'd expect better from what was originally a very expensive instrument from the biggest accordion company in the world.

My other question also came up when attempting to wax those reeds back into place - the gaps between the treble reeds are something like a millimeter - or less?  No way you can dribble stuff down between them, with all the, I think the term is capillary action, the wax is more interested in grabbing a hold of the reeds on either side instead of flowing downhill like it should.  I made a little quick and dirty attachment out of sheet copper a bit like George advocates using, just to get some heat between those reeds, and managed to get sufficient wax to flow, kind of.  By the last reed it occurred to me to just set wax in place first, and then melt it...what do you experts do here?
Logged

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: Wax embrittlement/tiny gaps
« Reply #1 on: September 15, 2015, 07:28:58 AM »

No problems with the amateur repairs I've done over the year.  But I only used an electric iron once. Usually I "warmed" an old meat skewer (3mm or so thick) in a gas flame until it was hot enough to melt wax on test. Rather more controllable.

I used to place "flakes" of wax where needed and then run it in situ. Yes, the plate gats warm and the liquid wax flows in nicely. I guess had I bent the "iron"s tip over it might have been even better.

Tent pegs have also been used in extremis at festivals, though aluminium doesn't keep much heat. Again, these didn't fall apart later
Logged
  _       _    _      _ 

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Wax embrittlement/tiny gaps
« Reply #2 on: September 15, 2015, 07:51:26 AM »

Anybody using soldering irons run into this issue?  Doesn't sound like it.  Certainly things can go wrong with wax, even on ostensibly top of the line instruments.  The wax in my Club Morino falls apart upon handling, as I was reminded the other night when I was fixing up a couple of silent reeds who'd stopped speaking when too many wax particles had fallen onto the tongues, and you'd expect better from what was originally a very expensive instrument from the biggest accordion company in the world.

Wax will deteriorate over time and becomes brittle and crumbly, even the highest quality wax in the highest quality instruments. Its chemical composition changes (slow oxidation, I would guess) and it absorbs moisture from the air. When you apply a hot soldering iron to old wax, it fizzes and spits at the iron tip. New wax doesn't do this.

Once it gets to the brittle stage (it may take 30 years or more) it no longer holds the reed plates securely. They may come loose at any time (usually the most inconvenient!) and the only proper action is to strip it all down, clean off the old wax thoroughly from the reed plates and the reed blocks, and then replace with fresh new wax. Before re-waxing you should replace all the valves too. After such along time they will almost certainly have curled or become stiff and less resilient with age. The you will need to re-tune the instrument. So - it's not a trivial undertaking, but one which unfortunately becomes necessary. It goes with the territory of owning/playing vintage instruments.

Quote
My other question also came up when attempting to wax those reeds back into place - the gaps between the treble reeds are something like a millimeter - or less?  No way you can dribble stuff down between them, with all the, I think the term is capillary action, the wax is more interested in grabbing a hold of the reeds on either side instead of flowing downhill like it should.  I made a little quick and dirty attachment out of sheet copper a bit like George advocates using, just to get some heat between those reeds, and managed to get sufficient wax to flow, kind of.  By the last reed it occurred to me to just set wax in place first, and then melt it...what do you experts do here?
There are threads about this on the forum; you will need to search for them.
Basically, I use a temperature-controlled soldering iron (readily available) and don't bother with a heat sink. Wax melts at around 180-200°C depending on the exact composition so your iron needs to be set at that temperature. If it gets too hot the wax will start to go brown and burn.

Where the reed plates are so close together that you cannot get the iron tip in between, one technique is to wax the first reed plate in position, leaving the waxing of the common long side until last. Then butt up the next reed plate to it on to the still soft wax, and continue the process all the way along.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: Wax embrittlement/tiny gaps
« Reply #3 on: September 15, 2015, 08:03:55 AM »

Gosh, that's very hot! In another context tin/lead eutectic used to solder electical components melts at (google… ) 188oC. I'd naively though that boiling water would melt melodeon wax?

Thanks for the tips on late brittleness, a treat in store …
Logged
  _       _    _      _ 

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Wax embrittlement/tiny gaps
« Reply #4 on: September 15, 2015, 08:14:33 AM »

Yes I think that figure is on the high side.
Pure beeswax melts at around 65C, rosin at a little over 100C, so the combined melting point should be something between those figures. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Wax embrittlement/tiny gaps
« Reply #5 on: September 15, 2015, 08:58:15 AM »

Yes I think that figure is on the high side.
Pure beeswax melts at around 65C, rosin at a little over 100C, so the combined melting point should be something between those figures.
OK - perhaps. I'm just going by the settings I need to use on my soldering iron to make the wax usefully flow, which is as I noted previously about 180 - 200°C. It's hard to determine an exact melting point as the wax softens considerably beforehand. It then flows more easily as the temperature is raised beyond its melting point, but not to the extent that it starts to burn.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Wax embrittlement/tiny gaps
« Reply #6 on: September 15, 2015, 11:28:02 AM »

Heat adjuster scales are very arbitrary  and that setting only relates to your iron it will probably be totally different on someone else's  >:(
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Wax embrittlement/tiny gaps
« Reply #7 on: September 15, 2015, 04:11:17 PM »

  I have a homemade heat-regulated iron I use, although I'm sure the factory adjustable ones work well. A "rule of thumb" I have adopted is, I adjust the heat to a point where the iron will readily melt the wax, but when left idle for, say, 2 or 3 minutes, the tip will just show a trace of smoke.
   Please also consider that there is a lag in the time it takes for the heat to travel to the tip, even after an increase on the adjuster. I always let my iron 'normalize' before I begin the waxing process to insure it is 'in the range'. If you are getting any smoke as you wax, then your iron is too hot. An un-regulated iron will burn the wax. You don't want to be breathing these fumes at all, either.  :-X
Logged

baz parkes

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1894
    • All Blacked Up
Re: Wax embrittlement/tiny gaps
« Reply #8 on: September 15, 2015, 04:28:04 PM »

Heat adjuster scales are very arbitrary  and that setting only relates to your iron it will probably be totally different on someone else's  >:(

A bit like ovens really...
Logged
On the edge of Cheshire's Golden Triangle, apparently...

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Wax embrittlement/tiny gaps
« Reply #9 on: September 15, 2015, 07:44:48 PM »

Heat adjuster scales are very arbitrary  and that setting only relates to your iron it will probably be totally different on someone else's  >:(

A bit like ovens really...

Possibly affected by altitude, too; we're at a shade under 3000ft ASL, and things definitely take longer to cook here. Personally I use Charlie Marshall's paintbrush method, so I just watch the melting wax until it looks ready to use - no idea what its temperature is......
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Wax embrittlement/tiny gaps
« Reply #10 on: September 15, 2015, 07:47:08 PM »

Altitude has an insignificant effect on melting temperature.  Boiling is a different matter.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

KLR

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 640
Re: Wax embrittlement/tiny gaps
« Reply #11 on: September 15, 2015, 09:48:57 PM »

I did find a couple of threads on dinky gaps.  Don't know what term I failed to look for before.  Wax 1st reed fully, then add next one and wax that, et al.  Theo says to leave tops and bottoms free until the end in case anything goes awry. 

What's the world's record for wax holding up?

Quote
Before re-waxing you should replace all the valves too. After such along time they will almost certainly have curled or become stiff and less resilient with age. The you will need to re-tune the instrument. So - it's not a trivial undertaking, but one which unfortunately becomes necessary. It goes with the territory of owning/playing vintage instruments.

The Club's mix of leather and plastic valves look like they're in great shape.  I might be crazy enough to rewax everything but revalving... :o  Never again!  I about keeled over revalving my 3 voice BCC#.  What a chore!  Like redoing a roof.  Hats off to any and all box techs, once more.   (:)
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal