Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: swapping Erica reed blocks  (Read 2234 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
swapping Erica reed blocks
« on: September 21, 2015, 04:15:57 PM »

I am considering swapping the A/D reedblocks from my new, Chinese-made Hohner Erica with G/C ones from an older, German-made Erica.  I understand that the system used to fasten the blocks down may differ from older Ericas to new ones (?), but is there any reason why my idea to swap blocks might not work?  Mine are fastened down with screws.  The reed blocks would be swapped with someone in Newfoundland and would have to be mailed...that brings up another question - how to safely package reed blocks for transport in the post?
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: swapping Erica reed blocks
« Reply #1 on: September 21, 2015, 04:25:34 PM »

Yes the holding down clamps can differ but it's not to hard to adapt the blocks or fixings.
The other difference is in the placing of te gasket.  On older Hohners the gasket is glued onto the reed block, on later ones its glued onto the base board.  If you end up with two gaskets you  have to remove one.  Always choose to remove the gasket from the block, because it is much easier to sand the block to remove traces of old glue and get a nice smooth surface.
The best gasket material is a textile material with a felted surface on one side, but you could use soft leather so long as it has a very even thickness - chamois/wash leather is not good because it varies in thickness.  Glue on the chosen material with pva.  When the glue is dry cut out the holes with a scalpel.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: swapping Erica reed blocks
« Reply #2 on: September 21, 2015, 04:41:11 PM »

The reed blocks would be swapped with someone in Newfoundland and would have to be mailed...that brings up another question - how to safely package reed blocks for transport in the post?
1. Wrap a layer of brown paper around each reed block and tape lightly into place. That will help protect the reed tongues and valves from the rest of the packaging.

2. Put a couple of layers of bubble-wrap around each reed block and tape into place.

3. Lay the wrapped reed blocks side-by-side and sandwiched between two sheets of strong thick card. Tape another layer of bubble-wrap around the sandwich.

4. Put the whole lot into a strong cardboard carton. Fill any remaining space on all sides/top and bottom with more bubble wrap scraps or polystyrene chips. Include a sheet of paper inside the carton with your address and the recipient's address, just in case the outer packaging gets damaged and the external addressing gets lost or illegible.

5. Tape all sides and seams of the carton securely with strong parcel tape.

6. On the exterior add the recipient's address and sender's address clearly labeled inside a transparent plastic pocket, taped securely on all sides. Mark the package clearly as 'Fragile'.

That should do the trick....

Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: swapping Erica reed blocks
« Reply #3 on: September 21, 2015, 08:14:21 PM »

Great packing advice, Steve - thank you very much!

Theo, my current Erica has the gasket on the baseboard, and not on the blocks.  If the blocks that get sent to me have a gasket on them, I will remove said gasket using the method you have transcribed, and keep the gasket on the baseboard.  I assume the holes would line up with the older blocks and the newer gasket?

It seems to me that it's rather easy to change keys within a box that has removable reed blocks.  Does anyone keep an extra set of blocks for an instrument handy in case you decide to change keys for a time? And then back again?  Just a thought...
« Last Edit: September 21, 2015, 08:16:31 PM by mselic »
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: swapping Erica reed blocks
« Reply #4 on: September 21, 2015, 08:16:21 PM »

Exactly, just need gasket on one surface.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: swapping Erica reed blocks
« Reply #5 on: September 21, 2015, 09:33:55 PM »

I'm not exactly an expert on Hohner Ericas, but my primary concern would be the offset from hole to hole. Maybe it's totally unfounded, but I'd make sure that the openings in the GC blocks are compatible with the ones in the faceboard of your Chinese box.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: swapping Erica reed blocks
« Reply #6 on: September 21, 2015, 10:02:57 PM »

Good point, but in practice Hohner blocks are remarkably consistent in respect of hole placement.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 613
Re: swapping Erica reed blocks
« Reply #7 on: September 23, 2015, 09:56:46 AM »

  Does anyone keep an extra set of blocks for an instrument handy in case you decide to change keys for a time? And then back again?  Just a thought...

yes I do  :||: I have number of Erica's and keep extra sets of reed blocks..as it happens I have 2 extra set of G/C blocks for Erica..German made of course  :D
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal