Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Reed block sizes  (Read 1448 times)

0 Members and 1 Guest are viewing this topic.

Luis Infante

  • Member
  • *
  • Offline Offline
  • Posts: 7
Reed block sizes
« on: September 23, 2015, 06:29:05 PM »

Guys,

is there a chart or a formula to calculate the size of the cavity for each reed plate in the reed block? thank you in advance!
Logged

Luis Infante

  • Member
  • *
  • Offline Offline
  • Posts: 7
Re: Reed block sizes
« Reply #1 on: October 09, 2015, 05:46:46 PM »

Nobody answer my posts  :(  :-[  :-X  :-\  :'(
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Reed block sizes
« Reply #2 on: October 09, 2015, 06:17:37 PM »

That may mean that nobody knows!  There are lots of considerations that might affect the sound produced, rather like gas flowing an engine perhaps, to maximise throughput (which should maximise volume) or tuning the airpath to the frequency of the reed hoping to make them responsive as the air flow will build a resonance, but I suspect that in practice the blocks are manufactured to accomodate the size of the reed plates and little more.  Perhaps there is a depth of chamber which works best for each builder, but beyond a few experiments to find this it would be complex to try to isolate each contributory factor and find which design features affect them.  Again, only suspicion, but perhaps these design features are what gives certain manufacturers a distinctive family sound as they will tend to go with what worked in their previous boxes.

Rob.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed block sizes
« Reply #3 on: October 10, 2015, 10:57:03 AM »

I don't think there is a formula.  There are so many variables both input and output that I can't imagine a formula would be useful.
Input variable include, but are not limited to: chamber length, width, depth, taper, wall thickness, surface finish, vent diameter, shape and position, thickness of base plate type of reed: scale length, width profile, thickness profile, material, tongue clearance, plate thickness etc
Output variables which may be affected by any of these are fewer, mainly tone, volume, response and dynamic range.
There is a discussion on this topic ever on concertina.net http://www.concertina.net/forums/index.php?showtopic=18126#entry172985
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Reed block sizes
« Reply #4 on: October 10, 2015, 05:20:05 PM »

There are a few discussions about this elsewhere. The consensus is that nobody really knows. Some people try to make them as small as possible whilst having the reed still sound, some try to make them as deep as possible.

My rule of thumb was to look at the likely maximum travel of the reed and add a bit. Could call it maybe 0.6* reed length? Idea is to make sure that the reed has enough space to move without impacting on the reed block. As far as I can tell there isn't any hard and fast rule of thumb other than making sure that the reed doesn't hit! diatonix might have more to say though.1
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Reed block sizes
« Reply #5 on: October 11, 2015, 12:19:49 PM »

I recall from deep and distant past that I read of music hall concertina players gluing slivers of cork into the chambers to reduce the "wasted" volume which increased the volume of the instrument.  However, there were no comments made about effects on the tone.  I guess it didn't really matter when trying to be heard over a theatre full of noisy drunks - sounds just like most of the places I play my melodeon!

Rob.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal