Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Advice on converting a Club box, please.  (Read 4944 times)

0 Members and 1 Guest are viewing this topic.

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Advice on converting a Club box, please.
« Reply #20 on: November 07, 2015, 09:42:32 PM »

Lester's scheme will give you a doubling of the beat rate each octave as you go up.

Yes indeed. That means the lower end of the scale will have a nice medium tremolo, which will become rather shrill at the upper end.
   A very useful feature of Dirk's is, that if you know and like the beating pattern of two points of the scale (say an octave or two apart) you can set those values into a calculation program which will interpolate the values for the entire scale for a smooth progression of the beating pattern.
   Then, the tuner will display the status of both reeds, (or even three reeds), and show a relative comparison of their position relative to + or -  with zero as a reference, as well as displaying the beating difference in terms of either cents or Hz, whichever value you select. You can also save your 'beating' pattern, and concoct other patterns for different instruments. If there's a better tool out there, I would like to know of it.
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Advice on converting a Club box, please.
« Reply #21 on: November 07, 2015, 11:33:43 PM »

I had an earlier version of Dirk's on a laptop, but never got around to using it.  Unfortunately the laptop is long deceased and despite a generous offer of a half-priced replacment, I can't afford it at present.  You can work out a slope of tremelos against pitch on graph paper and it's not difficult to convert from Hz to cents, though for setting tremelo it's probably easier in Hz.

I have a set of needle files and a saw sharpening file, but I was thinking of a lifter and a pinger/steady.  Although many consider it sacrilege, I recall seeing a youtube video of a tuner poking a dremel up into the block to flatten the inside reeds, although he had to lift and steady from outside for sharpening.  No real reason you can't scrape from the inside, then?

Oh well, a few goes and I'll find out what works hopefully before I have to buy too many new reedplates!  Another advantage to trying out on a Pokerwork - the reeds are generally available.

Rob.
Logged

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Advice on converting a Club box, please.
« Reply #22 on: November 07, 2015, 11:49:22 PM »

Rob, you may find this video helpful from Olav B. of this parish  (:)  However, beware of the  >:E Dremel >:E
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Advice on converting a Club box, please.
« Reply #23 on: November 07, 2015, 11:56:25 PM »

Yes, I saw that video and was thinking of one day making some of the tools shown - particularly the Italian style lifters and steadies.  Should be possible, though my preferred starting point would be a selection of dentist's stainless tools.  They can sometimes be found at jumble sales, but I haven't seen any for some while.

Rob.
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Advice on converting a Club box, please.
« Reply #24 on: November 12, 2015, 03:17:01 PM »

I hadn't expected to be back so soon!  I got the tool set from CGM and immediately put a well defined scratch across my steel rule.  On opening up the Pokerwork, I found most of the reeds have a coarsely ground dimple about a third up from the root, presumably a dremel in use?  The strange part is that despite a number of scratches between the dimple and the root I can barley flatten the pitch.

Has anyone else met with this and if so, what is the best way to tune such a reed?

Rob.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Advice on converting a Club box, please.
« Reply #25 on: November 12, 2015, 03:21:21 PM »

Is your scratcher sharp?  I keep a fine diamond sharpening plate by me when tuning and give the tip of the scratcher a regular touch up to keep it cutting keenly.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Advice on converting a Club box, please.
« Reply #26 on: November 12, 2015, 04:17:01 PM »

Brand new and scratched my steel rule with practically no pressure.  The reed now has so many scratches it#s starting to look like a gulley, but has only moved around five cents in pitch!

Rob.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Advice on converting a Club box, please.
« Reply #27 on: November 12, 2015, 04:26:43 PM »

Scratchers are designed to make quite small changes in pitch.  How far are you trying to go? 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Advice on converting a Club box, please.
« Reply #28 on: November 12, 2015, 04:30:42 PM »

I'm trying to tune from around 7 cents sharp to 8 cents flat.  Mind you, the iStroboSoft wanders around about 4 cents... (could be my heavy breathing)

Rob.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Advice on converting a Club box, please.
« Reply #29 on: November 12, 2015, 05:01:50 PM »

It's not istrobosoft wandering, it's the pitch of the reed changing as you sound it.  You need to be able to give the reed a good long steady blow to get a stable pitch, and the valves need to be working perfectly too.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Advice on converting a Club box, please.
« Reply #30 on: November 12, 2015, 06:36:26 PM »

I hadn't expected to be back so soon!  I got the tool set from CGM and immediately put a well defined scratch across my steel rule.  On opening up the Pokerwork, I found most of the reeds have a coarsely ground dimple about a third up from the root, presumably a dremel in use?  The strange part is that despite a number of scratches between the dimple and the root I can barley flatten the pitch.

Has anyone else met with this and if so, what is the best way to tune such a reed?

Rob.

Rob...I think that the Hohner factory sometimes used a jig to give reeds an approximate pitch, and that the jig would use a cylindrical grindstone  to remove material in the mid or root areas. These are usually very precise grindings, and easily distinguished from a hand-held dremel tool. Then the reed would be fine-tuned by filing or scratching. Attached is a photo of reeds in my 90 year old Hohner 3 row. The ground areas are the dark bands on the outer two reeds. BTW, this box still uses almost all of its' original leather valves, they still seem to work just fine. Not always the case though.
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Advice on converting a Club box, please.
« Reply #31 on: November 13, 2015, 12:55:30 AM »

That's interesting, Forrest, and not too surprising.  I saw a youtube video of a factory tuner using a sort of belt sander across the reeds to set the rough pitch (wasn't Hohner, though).  The dimples in my reeds are quite small and about a quarter of the width of the reed tongue, so I guess they're using a much smaller diameter and width of grinding wheel, which is why I likened it to the much derided Dremmel.

Actually I got in closer with a magnifying glass and realised that my scratches had very litle depth, so rubbed up the tip of the scratcher and gave it a couple of good welts - now we're making progress.  Sorry I didn't report progress sooner, but I had to get to work (evening shift).  I hadn't realised just how inconvenient and difficult it is to work without a tuning table.  The bellows take on a life of their own without the pins in place making it nearly impossible to get a good long, steady tone for the tuner.  I'll probably have worn out the screw head of the block retainer by the time I'm half done.  Still, it's the kind of experience that gives insight as to which design of table would best meet one's needs.

Rob.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Advice on converting a Club box, please.
« Reply #32 on: November 13, 2015, 07:39:00 AM »

I hadn't realised just how inconvenient and difficult it is to work without a tuning table.  The bellows take on a life of their own without the pins in place making it nearly impossible to get a good long, steady tone for the tuner.  I'll probably have worn out the screw head of the block retainer by the time I'm half done.

In that case try scratch in the reeds with the block fixed in the instrument. Not difficult when lowering pitch, and you will save some time too.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal