Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: pallets  (Read 2607 times)

0 Members and 1 Guest are viewing this topic.

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 614
pallets
« on: November 16, 2015, 03:40:35 PM »

Hello all;
In the past I have managed to re-face pallets on my old Hohner’s with success, used  Charlie’s special felt & leather 2,3 and 4mm no problem..very recently I had a go on a 114- and Erica. 114 failed miserably and it is now worse than what it was, all leaking , pallets are not sealing & plays without pressing and button...springs are in good concision and seems to be working OK.
 
on the  Erica treble side worked well no issues but bass side is again not sealing properly and with a little force some cord reeds stars playing..I have changed & tried different thickness on the facings starting from 2mm to 4mm but did not work..I have even changed the whole mechanism on the bass side to see if any better but no luck still leaking...I’ve applied a gasket (1.5mm thick ) on the sound board hoping it will help if there is any un even surface but that did not help either..
Question is what am I missing or where did I go wrong ? how do I fix leaking pallets now ? many thanks 
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: pallets
« Reply #1 on: November 16, 2015, 04:09:33 PM »

Pallets have to lie completely flat, that is really all there is to it.  But they can fail to lie flat for several reasons.  Lever arms can be twisted which will lift one side of the pallet. If the new facings are too thick then the lever can bear on the edge of the pallet instead of the centre( most likely on the 114 if you have significantly increased the thickness). And of course weak springs, and friction in the mechanism don't help either.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: pallets
« Reply #2 on: November 16, 2015, 05:30:05 PM »

Question is what am I missing or where did I go wrong ? how do I fix leaking pallets now ?
Did you remove the pallets from the lever arms in order to replace the facing felt/leather? That's the proper way to do it.

Then - to reattach the pallets to the lever arms (after cleaning off all the old glue from the arms and the pallet slots) you place all the pallets in their proper positions flat on the pallet board and with the lever arm ends in position in the pallet grooves. The pressure of the springs should keep the pallets in place. Then use a small blob of hot-melt glue no the ends of the lever arms just spreading on to the pallet. That will be sufficient to hold them. Doing it this way ensures that the pallets close flat against the openings and hopefully not result in air leaks.

You will then find the button height will be too low, due to the increased thickness of the new pallet facing. You can adjust this by very carefully bending the pallet arm away from the pallet board; use your fingers to ease back the lever arm holding the arm just down a bit from the pallet. just a gentle easing is all that's required. Go slowly and carefully and try to ensure that the new button height is consistent across the length of the keyboard.

Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 614
Re: pallets
« Reply #3 on: November 16, 2015, 09:40:17 PM »

  Lever arms can be twisted which will lift one side of the pallet.
Thanks Theo, some of the pallets are lifting up for sure,if I push them down with my finger I can see them rocking enough to leak

and thanks Steve.. I did them all proper way as you said..and this isn't the first time for me but never had any problem in the past..problem I'm having with this two box 'new' to me not sure what went wrong 
« Last Edit: November 16, 2015, 09:45:19 PM by invadm »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: pallets
« Reply #4 on: November 16, 2015, 09:48:37 PM »

it is harder with 114 pallets because they are so long which makes the change of geometry more critical when you use thicker felt.   One possible fix is to raise the action slightly by placing a thin sheet of ply or similar under the mechanism.  You will need longer fixing screws, and check that the buttons still clear the edge of the holes in the keyboard.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 614
Re: pallets
« Reply #5 on: November 16, 2015, 09:58:54 PM »

facings I have used on 114 was 4mm first & did not work than I removed them all and replaced with 2.5mm..both failed...I have extra set of original pallets for 114 they don't seal properly either...I'll have a go raising the whole mechanism and see how it goes on 114. I might have some springs too  (:)     
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: pallets
« Reply #6 on: November 16, 2015, 10:19:39 PM »

Don't raise the mechanism until you have eliminated other simpler causes!  it should not be necessary with 2.5mm material
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: pallets
« Reply #7 on: November 17, 2015, 12:04:43 AM »

It sounds as if you are doing all the right things, yet the continuing leakage remains a problem.

Theo's point about the increased sensitivity of long pallets is a good one. Is the leakage occurring at all the pallets, or is it just a very few? One thing which has caused a problem for me (just once) has been faulty pallet facing material - the thickness of the felt layer was slightly uneven, resulting in a slight undulation of the thin leather layer making it impossible to achieve a good seal over the length of the pallet. Replacing the facing once again from a different batch of facing material cured the problem.

One 'tool' I find useful to identify the position of leaks is a narrow strip (approx. 5 mm wide) of 'Rizla' type cigarette paper used like a feeler gauge: slide the strip under the pallet at the position of each vent hole, then gently try pulling it out. If the seal is good, the pallet will 'grab' the Rizla strip. If it slides out easily, that's one place where there will be a leak. The narrow strip will allow you to test each section of each pallet in turn. It should also allow you to discover if, say, the pallet face is longitudinally tilted/twisted, so that one long edge is bearing down before the other edge. If so, try adjusting the tilt by making a very slight compensatory twist in the lever arm using a pair of small round-nosed pliers.

One other point:
The wood face of the pallet must be perfectly planar and flat to begin with. If there are any deviations from planar (caused perhaps by uneven sanding or scraping when removing old facing/glue) then the new facing material will take on these undulations and once again make it difficult to achieve agood seal. The Rizla strip feeler gauge will help identify this. If so, it might be necessary to start again :( - strip off the facing material and then gently sand down the wood pallet face to absolute planarity by rubbing on fine sandpaper taped/glued to a glass sheet.  Beware of applying uneven pressure to one edge or end which will lead to an undesirable convex surface.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: pallets
« Reply #8 on: November 17, 2015, 08:15:47 AM »

One other tip:  the slot in the pallet must be clean. Draw a hacksaw blade through the slot to remove bits of glue and other debris.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: pallets
« Reply #9 on: November 17, 2015, 10:18:06 AM »

facings I have used on 114 was 4mm first & did not work than I removed them all and replaced with 2.5mm..both failed...I have extra set of original pallets for 114 they don't seal properly either... (:)   

This could possibly indicate that the pallet board itself is compromised.  Check to see that the vent openings are completely clean and flush with the pallet board surface - no splinters or other debris stopping the pallet seating properly.

There might also be ripples or undulations in the pallet board surface, again preventing a complete seal. (Rees and I both know about this one!). You will need to remove the action to check this with a straight-edge. If there are undulations, the only solution is to scrape and/or sand the pallet board surface flat, but be very, very careful to do it evenly over the whole area to avoid making any additional concavities.

The only other remaining problem area will be the action springs. You say these seem to be in good condition, but can you be sure they are actually applying sufficient closing force (especially on a 114 where the pallets have a relatively large surface area)? They may have become weakened over the years. Try getting someone to help by pressing down gently on the pallets while you pressurise the bellows. If gentle finger pressure seems to cure the problem it might just be worth replacing the springs anyway.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 614
Re: pallets
« Reply #10 on: November 17, 2015, 11:08:48 AM »

all pallets are cleaned and dirt /dust/glue free and sanded down on a thick glass table(1 cm thick)..on glass table they all sitting flash...most of the pallets are leaking not just one or two and if gentle finger pressure applied leaking stops.
but I have not yet checked the sound board it self to see if it's compromised.I will change the springs first than look in to all the other possible part/ places suggest by Steve and Theo.               
Logged

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: pallets
« Reply #11 on: November 17, 2015, 01:11:28 PM »

Just a thought, and something that hasn't yet been suggested, but is the key frame firmly attached to the instrument? Those 4 pesky little brass screws can be a cause of all sorts of action woes if they are not firmly attached, or if the screw holes have become enlarged. Take care not to over-tighten them though, but the back of the key frame must be flat and straight against the wood. (I have sometimes had to replace the screws with 2mm dia. nut and bolt sets, available from all good model shops.)

Another suggestion is to check for pad leaks without the keyboard cover in place. It is possible that the top  edge of the button arm is fouling against the underside of the keyboard cover top. This could be caused by the keyboard being installed at the wrong angle, or (as I remember finding once on an Erica) that all the button arms had been bent upwards by the owner to give a higher button action in the hope of greater volume!

Maybe all obvious things you have already looked at, but perhaps worth checking again....
Logged
Tuner/repairer, now retired.

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 614
Re: pallets
« Reply #12 on: December 08, 2015, 10:03:08 AM »

finally all fixed  (:) and it was the failing springs,changed them all and fitted new bellow gasket and box is now as good as new..thanks for all your help and advise.. :||:     
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: pallets
« Reply #13 on: December 08, 2015, 10:31:29 AM »

finally all fixed  (:) and it was the failing springs,changed them all and fitted new bellow gasket and box is now as good as new..thanks for all your help and advise.. :||:   

Excellent news! Well done.  (:)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal