Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Reed blocks  (Read 1749 times)

0 Members and 1 Guest are viewing this topic.

Mike-T

  • Good talker
  • **
  • Offline Offline
  • Posts: 90
  • 1930s Hohner B C C#, D/GAcc Benny, 2.5 Beltuna
Reed blocks
« on: December 02, 2015, 08:13:33 PM »

Hi Guys, I'm in the process of changing keys on a Hohner Erica, replacing old T reeds with a new set of Harmonikas, my problem (and the resulting question) the base reeds are approx. 6 mm thick plates as opposed to Hohners 3mm, the extra thickness + the protrusion of the rivets makes fitting the reed block back in place practically impossible without a load of block modification.
So the Q, is the depth of the chamber in the reed block critical? can I rebate the block to sink the reed plate into it without messing the thing up to much?
regards
Mike.
Logged

benammiswift

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 158
  • Squeezing for Derbyshire
    • benammiswift.co.uk
Re: Reed blocks
« Reply #1 on: December 02, 2015, 09:05:22 PM »

I have a very limited knowledge of reed blocks but I know that reed block for instruments such as Castagnaris are precision made with the correct chamber size for each reed so it sounds properly and has good harmonics as well as overall good responsiveness.

However, on the flip side, all hohner erica reed blocks are the same for every tuning so you need someone who is actually an expert in this field to give you and definitive answer or pros/cons of doing this
Logged
Castagnari Handry 18

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Reed blocks
« Reply #2 on: December 02, 2015, 09:17:15 PM »

Castagnaris are precision made with the correct chamber size for each reed so it sounds properly and has good harmonics as well as overall good responsiveness.
I have just opened up a yet another Lilly to convert it to 4th button start and again it proves the above supposition to be incorrect.

Castagnari appear to make D/G boxes by using probably G/C casework and the they lay masking tape to bridge the resulting gaps at the top of the reeds (D/G reeds being shorter) and then they wax over the tape. Thus the reed cavities are not 'matched' to the reeds. This seems to be the common solution for D/G Lillys.

All the boxes I've done seem to me and their owners to have been improved by the mod which, of course, better matches the reed size to the cavity due to the reed shift.

Lars

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 797
Re: Reed blocks
« Reply #3 on: December 02, 2015, 09:57:44 PM »

I fitted some Harmonikas bass reeds to a Hohner last week, and had the same issue. I got around it by removing one of the side strips (the wooden strip on the soundboard that act as side-guards for the bass and chord blocks), and carefully 'sliding' one of the blocks in place after inserting it 5 mm too far to one side. Thus avoiding the rivets catching on the other block, as you mention.

This resultet in the soundhole perhaps being 1mm or so off-center from the soundboard to the bass block, but I found that it still worked absolutely fine, and I naturally tuned the reeds in this place.

Two things to consider:
1:
I made sure that it was the bass block, not the chord block, that had to 'slide' into place. The holes in the chord block are smaller and more sensitive to small movements, at least that's my theory.
2:
The long bass reed and somewhat long chord reeds from Harmonikas are showing more 'movement' than Hohner reeds, which meant that you may find that if you play a push bass note and chord very vigorously, they 'buzz' against each other. I had blocked the side of the somewhat wide Hohner bass block to accomodate the narrower Harmonikas bass reed, and solved this by moving the blocking strip to the other side, thus ensuring that the push reeds were not directly across from each other. You REALLY had to push them to get this buzz, but not a pleasant sound at all.
Logged

Mike-T

  • Good talker
  • **
  • Offline Offline
  • Posts: 90
  • 1930s Hohner B C C#, D/GAcc Benny, 2.5 Beltuna
Re: Reed blocks
« Reply #4 on: December 03, 2015, 10:35:06 AM »

HI folks, am a happy bunny now after Lars input, I was almost there through trial and error doing exactly the same things he did it was just the last step I needed advice on. Thanks to Lester and the others also for input. (now the tuning)
regards
Mike.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal