Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: New Bb/Eb project box  (Read 1920 times)

0 Members and 1 Guest are viewing this topic.

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
New Bb/Eb project box
« on: December 10, 2015, 12:16:19 PM »

So I picked up a very nice Bb/Eb Hohner Erika; aside from the valves being a bit shot it's in near perfect condition. It has apparently had one owner from new, which is pretty incredible, and has obviously been looked after. Also came with a bunch of old German tunebooks which I might scan at some point, as they're also in great condition.

I've got a much poorer condition C/F Erika too, and I'm thinking of using it primarily for spares and reed swaps. I have to revalve everything anyway so I figured I might as well switch the layout whilst I'm at it. This is the Bb/Eb equivalent of my D/G layout that Mr Rowbotham is switching another Erika to:



Anything in red is a change, orange indicates a reed I don't have exactly. I've gone through and tried to figure out what would be the closest reeds that could be shifted to the correct pitch, with anything in green being on the Bb/Eb box already.

There are two which look a little questionable: I don't have anything within a semitone of the low B/B accidental, the closest being an A/C. I'm not sure if that's close enough to be tuned to B/B.

The other being the Ab/Ab bass and chords. I don't have anything close to that on either box, so I'll probably need to source those reeds from somewhere else.

Do those reed modifications look doable though? I'm not sure if it's best to move a reed sharper or flatter to reach a target pitch, but the replacement reed plates should all be within a semitone at least.

Any advice would be much appreciated; I'm really keen to get this Bb/Eb box set up right. I'll get the tuning done by an expert but I'll be trying to do the rest of it myself ;D
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: New Bb/Eb project box
« Reply #1 on: December 15, 2015, 03:29:53 PM »

It looks like you should be OK on the treble side as the worst case is a full tone shift - might get a slightly changed tone but it will work till you can find a new reedplate.  The Ab/Ab will depend on what happens when you remove the tip weights from the original Db reeds, but the chord reeds are the real problem.  When I made similar enquiries, the verdict was that the chord reeds would need to be replaced, but no-one was brave enough to suggest where I might source suitable plates.  I suspect that PA reeds would be best as they are unisonoric, but I must still enquire whether there is a suitable Hohner PA donor of the correct period as the scale length would be critical to fit the blocks closely enough.

Rob.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: New Bb/Eb project box
« Reply #2 on: December 15, 2015, 04:52:26 PM »

Chord reeds aren't  a problem.  With the Hohner method of keeping the closest pitch reeds on the same plate you will have one plate that already has Ab both ways, and the other two will only need to be moved a semitone.   The reeds should be:

Db/C
F/E
Ab/Ab

so just Db and F down a semitone each.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: New Bb/Eb project box
« Reply #3 on: December 15, 2015, 06:03:03 PM »

Ooh great, thanks guys; that's really helpful. So the only replacement reeds I should really look for are the Ab/Ab bass reeds (I've not looked at removing the tip weights, is that likely to work?) and that low B/B if the A/C reed is a bit too far away to switch.

Going to sort out the pads and other bits this week, and then revalve it and switch the plates over christmas. I've been after a Bb/Eb for ages so I'm really excited to get going on it ;D
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: New Bb/Eb project box
« Reply #4 on: December 15, 2015, 06:13:47 PM »

Ooh great, thanks guys; that's really helpful. So the only replacement reeds I should really look for are the Ab/Ab bass reeds (I've not looked at removing the tip weights, is that likely to work?)


Yes that should work for the low bass reed, the higher one will require lots of filing.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: New Bb/Eb project box
« Reply #5 on: December 15, 2015, 06:25:55 PM »

I've got a much poorer condition C/F Erika too, and I'm thinking of using it primarily for spares and reed swaps. Iup right. I'll get the tuning done by an expert but I'll be trying to do the rest of it myself ;D

What`s the fingerboard like on the scrapper , I could do with one for my Club-Modell-II (which is basically an Erika with plainer graphics on the ends)
Logged
Q: How do you cure MAD?
A: Buy more Boxes

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: New Bb/Eb project box
« Reply #6 on: December 15, 2015, 06:28:22 PM »

I've got a much poorer condition C/F Erika too, and I'm thinking of using it primarily for spares and reed swaps. Iup right. I'll get the tuning done by an expert but I'll be trying to do the rest of it myself ;D

What`s the fingerboard like on the scrapper , I could do with one for my Club-Modell-II (which is basically an Erika with plainer graphics on the ends)

It's not in bad nick but it would need painting! Are the fingerboards the exact same size? :D
Unfortunately I've just deposited that box with my parents, so I won't be able to take a photo of it until next week.
Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: New Bb/Eb project box
« Reply #7 on: December 15, 2015, 06:34:06 PM »

Theo reckons so and it makes sense (they`re both "oversized pokerwork" type boxes with two rows + 4 accidentals from the 1930s

the Erika seems to be the more cosmetically posh version of the Modell-II (see my thread for pics) , mine needs a lot more than painting as it`s a 1-piece version and it`s cracked between the buttons and a chunk is missing , please let me know how much you`d like for it :) .. if the wood is solid then it`ll be fine, I can sand and paint it
« Last Edit: December 15, 2015, 06:36:00 PM by Adam-T »
Logged
Q: How do you cure MAD?
A: Buy more Boxes

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: New Bb/Eb project box
« Reply #8 on: December 15, 2015, 07:03:37 PM »

Oof, yeah the repairs for the one-piece keyboards suck; I've just managed to glue an old pokerwork-esque one back together but I'm thinking of sanding it back and using a thin piece of wood on top as a more permanent repair. I found the missing chunk on that one; it was lodged in one of the airholes for a treble reed :o

I'll send you a picture next week when I'm back near it; it's one of the two-parter ones with a plastic fingerplate. How would £15 sound?

Going to try to fix the bellows on that scrap box, then use them as tuning bellows I think (:) Far less fussed about restoring that box than this lovely Bb/Eb beastie (even the grille is in good condition!):

Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: New Bb/Eb project box
« Reply #9 on: December 15, 2015, 07:59:47 PM »

I'll send you a picture next week when I'm back near it; it's one of the two-parter ones with a plastic fingerplate. How would £15 sound?

Sounds fair to me, thanks ! .. that Bb/Eb looks good ! . I was hoping this one of mine would be in that key but of course, it`s C/F like 99.999% of them are ...

Another Erika difference I`ve noticed in your pic (apart from the simpler more classy looking graphics) is the Hatching on the Gleichton like the later club boxes had and also the early D-Rays on the "black dot" ........

This is "as got" - I`ve started the clean up on the treble end  and tried Acetone to clean off the crazed corrupt varnish on the top without losing the lettering and its worked largely
« Last Edit: December 15, 2015, 08:08:50 PM by Adam-T »
Logged
Q: How do you cure MAD?
A: Buy more Boxes

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: New Bb/Eb project box
« Reply #10 on: March 03, 2016, 03:19:21 PM »

Finally gotten around to starting some work on this box (needed to figure out how many valves I need to order). Spent a bit of time today trying to clean up those treble buttons; turns out a scouring pad and some methylated spirits works pretty well!



Might need a bit more elbow-grease to get the last of the ink off of them but it doesn't look like I'm going to have to sand them down at all at least.
« Last Edit: March 03, 2016, 03:24:05 PM by robotmay »
Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: New Bb/Eb project box
« Reply #11 on: March 03, 2016, 06:12:45 PM »

Mine are pretty much the same colour as each other so I`m leaving as is . I do need to get around to sanding that fingerboard down and fitting it
Logged
Q: How do you cure MAD?
A: Buy more Boxes
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal