Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Base chord reeds  (Read 1833 times)

0 Members and 1 Guest are viewing this topic.

Mike-T

  • Good talker
  • **
  • Offline Offline
  • Posts: 90
  • 1930s Hohner B C C#, D/GAcc Benny, 2.5 Beltuna
Base chord reeds
« on: December 10, 2015, 03:50:48 PM »

Hi folks, I'm changing a 3 voice B/C to a D/G and wondering if one of you wonderful people could give me a breakdown on the reeds used for the base chords? I already have  a 3 reed set but the box needs a 4 reed set so am looking for the missing reeds (if that makes sense)?
regards
Mike.
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Base chord reeds
« Reply #1 on: December 10, 2015, 04:08:58 PM »

The standard Hohner D/G (Pokerwork/Erica) reed sets are as follows

G/D - G3/F#3 - D4/D4 - B3/A3
C/C - C4/C4 - E4/E4 - G3/G3
D/A - D4/C#4 - A3/A3 - F#4/E4
B/Em - B3/B3 - D#4/E4 - F#3/E3

These use Hohner's way of working of having the closest pitches on the same plate, if you want removable thirds a different pairing will be needed.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Base chord reeds
« Reply #2 on: December 10, 2015, 04:14:55 PM »

That depends on two things:   

What are the reeds you already have and which reeds are paired together on each reed plate?
What additional reed does your box require?  It is usually the tonic,  sometimes at the same pitch as the one you have, and sometimes an octave higher.  Which you choose will depend on what sound you want.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Base chord reeds
« Reply #3 on: December 10, 2015, 04:15:43 PM »

The standard Hohner D/G (Pokerwork/Erica) reed sets are as follows

The OP says its a 4 reed chord, so that means it's not an erica.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Mike-T

  • Good talker
  • **
  • Offline Offline
  • Posts: 90
  • 1930s Hohner B C C#, D/GAcc Benny, 2.5 Beltuna
Re: Base chord reeds
« Reply #4 on: December 10, 2015, 04:42:22 PM »

Hi Theo, That's correct, the box is an old corso. I was hoping to use the same or similar, D/G set that I used in an Erica, that sounds sweet as a nut before final tuning, it wasn't till I opened up the base end of the corso I realised it needed 4 reeds.

Mike.
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Base chord reeds
« Reply #5 on: December 10, 2015, 04:50:58 PM »

I'll try again  :-[

Currently converting a 30 button Club which has 4 voice chords from C/F to D/G. Attached is my plan for the bass end which shows the original C/F voicing and the intended D/G voices. As can be seen the root of each chord is present in 2 octaves (these are also used in the basses giving them 4 voices over 4 octaves).

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Base chord reeds
« Reply #6 on: December 10, 2015, 04:58:25 PM »

Hi Theo, That's correct, the box is an old corso. I was hoping to use the same or similar, D/G set that I used in an Erica, that sounds sweet as a nut before final tuning, it wasn't till I opened up the base end of the corso I realised it needed 4 reeds.

Mike.

You can just leave out the 4th reed is you prefer the three reed sound.  You just need to tape over the hole in the base of the reed block.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Mike-T

  • Good talker
  • **
  • Offline Offline
  • Posts: 90
  • 1930s Hohner B C C#, D/GAcc Benny, 2.5 Beltuna
Re: Base chord reeds
« Reply #7 on: December 10, 2015, 05:02:45 PM »

Thanks guys, very much appreciated,, I'll root through my spare reeds and see if I can find the octave reeds to match otherwise it's plan B and sticky tape time :)

regards
Mike.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal