Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2] 3 4   Go Down

Author Topic: Club Modell II  (Read 11241 times)

0 Members and 1 Guest are viewing this topic.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Club Modell II
« Reply #20 on: December 15, 2015, 03:15:41 PM »

Have you inspected the reeds for rust, especially on the treed plate enclosed side. Can be a real pain to remove.

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Club Modell II
« Reply #21 on: December 15, 2015, 03:23:14 PM »

I`ve yet to see one of these old hohners without any whatsoever , this has very little, just the usual scattering here and there as seen in all the pre-70s Hohners I`ve opened , far from the "more rust than metal" which they can get like ... the reeds will have to be removed for waxing and valving anyway
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Club Modell II
« Reply #22 on: December 15, 2015, 03:43:34 PM »


Proof of the one-piece fingerboard

Well that is unusual.  If you decided to replace it rather than repair I think the usual built up type would probably fit without too much trouble.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

911377brian

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1518
Re: Club Modell II
« Reply #23 on: December 15, 2015, 05:05:28 PM »

Didn't NickCB have some plating done fairly recently?
Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Club Modell II
« Reply #24 on: December 15, 2015, 06:00:51 PM »

Well that is unusual.  If you decided to replace it rather than repair I think the usual built up type would probably fit without too much trouble.

I`m going to have a go at PVA'ing the cracks and then filling the one gap with a piece of wood but if that fails, I`ll need a replacement if you`ve got any ideas  of where to get one ..
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Club Modell II
« Reply #25 on: December 15, 2015, 06:40:42 PM »

Well that is unusual.  If you decided to replace it rather than repair I think the usual built up type would probably fit without too much trouble.

I`m going to have a go at PVA'ing the cracks and then filling the one gap with a piece of wood but if that fails, I`ll need a replacement if you`ve got any ideas  of where to get one ..

I would chose some thinnish superglue for the cracks as it has good capillary action to draw the adhesive into the cracks

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Club Modell II
« Reply #26 on: December 15, 2015, 08:02:35 PM »

I use your Superglue technique for making sure box ends are sealed (unless there are glaring gaps, then PVA is needed) but the splits here are clean and open so PVA is the only possible rescue - looks like I`ll have a replacement Erika one coming anyway :) but I`ll have a go at salvaging this one as a project anyway
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Club Modell II
« Reply #27 on: December 16, 2015, 12:50:27 AM »

If the worst came to the worst, you could always run a planer over the top to give some depth to add a top plate.  To be honest, the top of the keyboard isn't actually necessary to the action.  We had one guy in the area who played a Corona which had lost nearly all the top face - didn't worry him or the box a bit.

Rob.
Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Club Modell II
« Reply #28 on: December 16, 2015, 08:40:51 AM »

Yup, it`s amazing what you can get used to - it`d been a while since playing a plastic fingerboard Pokerwork/Erica without the button travel limited when I got my current Erica and it was weird having my fingers disappearing down the holes, I`ve promised myself to do the Theo-mod (wood strip under the action) after the Club-Too is done but by then , I`ll probably be used to it again and not bother ;) ......

I`d rather have a fingerboard with all the holes intact but I`d take a Corona-III with bits missing than none at all :D 
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Club Modell II
« Reply #29 on: December 19, 2015, 04:23:47 PM »

Hokay the 1st stage is done  ...

I always do the structural and cosmetics before the waxing / valves / pallets etc because having a nice looking box in front of me give me incentive to do the less enjoyable tasks and I do it an end at a time ..

the past two 30s Hohners I recovered, I "relic`d" , their finishes were totally trashed but apart from the varnish going chalky (faintest touch leaves a while line) and buckle rash underneath, the box`s cosmetics are savable  .. I used Acetone to de-chalkify the varnish rather than trying to sand as I wanted the Hohner `transfers and as much of the stain as possible intact - I then used Finishing oil on top in numerous coats followed by Warwick bass guitar finishing wax , it`s worked, it`s fixed and stable , no chalkiness and only a bit of the red in Hohner was lost , in fact it`s helped the "loved" look of the box , the buckle scratches underneath now look natural and the front end has now got the Not-mint but genuinely nice look ..

I painted the grille in black , I dislike silver paint in the extreme (the orig was gold) and made a grille cloth from a tiger print chiffon scarf from a charity shop (as it was yellow / brown) ..

The Fingerboard is made from the crappiest wood , the thick hohner paint was covering up all sorts of issues such as areas around a knot (the knot itself being on the bit they discarded and the rest of the wood pitted and poor .. I PVAd the cracked parts and made a bridge between the broken bits with matchwood and PVA'd in , more PVA used afterwards under and on top of the breaks to finish and the lot was sanded and painted - I left the underneath intact due to the labelling .. I still really would like to buy Robotmay's donor fingerboard as its a two-part Erika one and in better nick but I did this one as a project anyway ..

Last bit was to do Lester's trick of running superglue around the inside of the fondo and edge joins on the reedblock side to remove any potential leaks ..

Pics of the Pre-painted but repaired fingerboard and the whole front end done - Please remember that I`m not a Chippie ;)

Logged
Q: How do you cure MAD?
A: Buy more Boxes

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Club Modell II
« Reply #30 on: December 19, 2015, 06:07:47 PM »

Very nice!  I particularly like the chiffon scarf - was that just happenstance that it turne up or has it been waiting to find an application?  I agree the overall look is not concourse, but well loved.  The Black grille is great, wonder if paint will stick to the chromed grille on the Pokerwork?  Not once I start trying to lever it in and out, amazing how they always make the grille larger than the hole...

Rob.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Club Modell II
« Reply #31 on: December 19, 2015, 06:11:19 PM »

If the grill gets tight just bend the turned edged slightly further back, especially in the vicinity of the fixings where they tend to get distorted.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Club Modell II
« Reply #32 on: December 19, 2015, 06:18:43 PM »

Thanks Rob - I actually went to the charity shop this morning with grille in hand to see what worked - black ladies slips, white net curtains, cream bed throws and other Chiffony things were looked at (much to the amusement of the old lady running the shop) - the scarf was the right colour and I like the brown streaks as they`re more transparent and you can see the pallets through them ..

the underneath buckle scratches are under the finishing oil and look "worn in" rather than messy, it`s a good look IMO especially as I didn`t want to sand back and lose the graphics and stain (which would have ended up patchy), the box looks natural rather than restored or tidied up .

Paint flakes off chrome too easily sadly Rob - you`ll need to either remove it (not hard with rusty Hohner grilles) or find a primer which will stick

Logged
Q: How do you cure MAD?
A: Buy more Boxes

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Club Modell II
« Reply #33 on: December 19, 2015, 06:21:42 PM »

Yes, I know - but this Chinese one resists all attempts.  If I get the best fit at the fasteners, which is pretty much imperative, it gets tight at the corners... and so it goes on.  It might work if I gently shave some wood out of the aperture, after all that's what the grille does every time I fit it, and I'd rather not end up with a bent grille.

Rob.

P.S. You can buy aerosols of car odours, e.g. New Rolls Royce, etc.  I wonder what they call the one they seem to use in UK charity shops?  Now there's a thought that'll take some beer to forget.
Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Club Modell II
« Reply #34 on: December 19, 2015, 06:28:39 PM »

Here are the two Relic boxes I did ..  1st was a black Doubleray from the same era as the Club Too - it looked as if it had been pulled out of a swamp, I`d never seen a box so mechanically sound so seriously trashed cosmetically....... Like the Club-Too, it was pristine inside and had never been opened, I`ve pics of the box as I got it ..

Second was a HA114-G which was in the same nick , sold to me at a good price by Tommy Gipsylad , it also looked like it had sunk onboard the titanic and likewise was in good tune .. I did both of these over 3 years ago

Logged
Q: How do you cure MAD?
A: Buy more Boxes

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Club Modell II
« Reply #35 on: December 20, 2015, 07:54:45 AM »

How did you clean up the case but preserve the decals on the Modell II? I am impressed (:)

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Club Modell II
« Reply #36 on: December 20, 2015, 08:07:49 AM »

I used Acetone (Nail varnish remover) carefully to clean up and seal the old chalky varnish , I didn't know if it would do it well but it worked..

Then used Liberon finishing oil afterwards, if you use enough coats and let them dry for half a day or more inbetween, it builds a shine even on non-bare wood.. the Warwick bass guitar surface finisher (like a tin of polish for their oiled basses) got it even and adds a tough surface . I used the warwick wax on the fingerboard also which I`d painted with a Matt "match-pot" (the tube type with the sponge applicator) as it made for a more natural looking surface than brushed gloss paint
« Last Edit: December 20, 2015, 08:09:44 AM by Adam-T »
Logged
Q: How do you cure MAD?
A: Buy more Boxes

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Club Modell II
« Reply #37 on: December 21, 2015, 06:00:11 AM »

I really like the look of the one row.....nice job!  ;)
Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Club Modell II
« Reply #38 on: December 21, 2015, 07:25:00 AM »

Thanks Forrest, it was utterly Mullered cosmetically and had a plastic fingerboard on (doesn't work with no grille , wood does) but I also at the time had a C one in "normal" nick with the grille on with a wooden F/board so swapped them over  ...  the air-spoon had been hacked down and put inside & had a button put on it for actuation, lester found me a suitably rusty spoon to replace it with so I could de-modify that, he did the bellows taping, the Italian ridged tape suits these boxes beautifully and is tougher

« Last Edit: December 21, 2015, 07:27:42 AM by Adam-T »
Logged
Q: How do you cure MAD?
A: Buy more Boxes

tom f

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 112
Re: Club Modell II
« Reply #39 on: December 21, 2015, 04:57:04 PM »

Fascinating thread Adam thanks!
Logged
Pages: 1 [2] 3 4   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal