Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 [3] 4   Go Down

Author Topic: Club Modell II  (Read 11199 times)

0 Members and 1 Guest are viewing this topic.

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Club Modell II
« Reply #40 on: December 21, 2015, 06:27:34 PM »

It continues -- the bass plate is varnished like the ends rather than painted black so I`m doing the same with the acetone to fix the old varnish and loads of finishing oil on top and replace the cloth over the holes with more tigerprint chiffon (one hole was pushed through otherwise I`d have left the original cloth there  ...

I`ll do the back end then like the front preserving the graphics but I need a wood step riser thing for the buttons if anyone knows where to get one (same as a pokerwork and all the 2815 type boxes) , if I made one it`d look bodgy in the extreme .

then clean up the bellows corners (the bellows are in good nick even cosmetically) , I do need to fix a patch on one of the gussets, I was going to use a piece of thin washleather , any idea what to stick it with ? .....
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Club Modell II
« Reply #41 on: December 22, 2015, 08:18:41 PM »

Wash leather isn't airtight.  I piece of thin soft lambskin or goatskin would be ideal.  The adhesive should be something that remains flexible when set.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Club Modell II
« Reply #42 on: December 22, 2015, 08:33:13 PM »

Thanks Theo - Evostik seems like a valid glue then and buying a gusset from Charlie Marshall and cutting a piece from that, the hole is on the flat part not a crease thankfully
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Club Modell II
« Reply #43 on: December 22, 2015, 10:32:23 PM »

I wouldn't use evostick if you want a permanent fix. I use Feibings LeatherCenent which is a type of pva. Bookbinding pva would work too. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Club Modell II
« Reply #44 on: December 23, 2015, 08:13:37 AM »

Excellent , thanks .. I`ll see where I can find some
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Club Modell II
« Reply #45 on: December 23, 2015, 05:07:56 PM »

I wonder how many of us have dabbed a little nail varnish remover on the back of an old box in the hope of getting such a nice finish?  Do you know the main ingredients of the Liberon finish?  I have some Deks Olje in the kitchen.

Rob.
Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Club Modell II
« Reply #46 on: December 23, 2015, 05:58:14 PM »

I have no idea what`s in it -  the stuff was recommended to me by someone on the forum and a tin seems to last forever, it`s really for bare wood and is easier to get a good finish on than varnish, doesn`t chip and looks better ...... Deks Olje ? - that`s gotta be a Swedish anagram surely
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Club Modell II
« Reply #47 on: December 23, 2015, 06:02:26 PM »

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Club Modell II
« Reply #48 on: December 24, 2015, 01:38:57 PM »

Thanks Lester, it unfortunately seems to get around revealing what it is by just saying "oil".  I suspect that like quite a few finishes it may be principally tung oil as this is the oil commonly blended into other oils as a drying agent.  Anyone who uses a wok will have become aware that boiling an oil makes varnish, trying to clean the stove top proves it!  I finally got it clean by soaking it in industrial strength detergent - exceeding recommended times threefold.  Omly trouble is it also removed the markings aroung the control knobs.

Deks Olje isn't an anagram, though perhaps we should have a competition along those lines.  I comes in two versions, the first a saturator which gives a matt or satin finish depending how many coats are applied and the second is a drying, gloss overcoat.  They are great but don't give a durable, permanent finish.  Well, not on my boat anyway.

Rob
« Last Edit: December 26, 2015, 02:03:02 AM by Rob2Hook »
Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Club Modell II
« Reply #49 on: January 01, 2016, 08:58:20 PM »

Rear end done .. I like that the bass plate is varnished too on this box , it cleaned up the same as the rest :)  ..

I need a bass button Riser - if I attemped to make one, it`d look too damn amateursish so has anyone out there got one to spare ?, it`s the same as all the other Hohners with them (Pokerworks etc) .

Logged
Q: How do you cure MAD?
A: Buy more Boxes

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Club Modell II
« Reply #50 on: January 02, 2016, 02:02:38 PM »

Actually they aren't that difficult to make. I replaced the one on the pimped Modell II in the pix here:
http://www.jollyrogeraccordions.co.uk/archive_of_boxes/hohner-modell-ii-cf-melodoen-for-sale/

(NB the box is now sold)

I made it from American oak. You just need to get the dimensions right and the holes in the right place. I shaped it with a sander (though at one pointed the band sander got a bit hot, broke and jumped a fair distance... and made me jump a bit too (:) )

It helps if you have the old one to use as a template.

« Last Edit: January 02, 2016, 02:04:55 PM by RogerThomas »
Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Club Modell II
« Reply #51 on: January 02, 2016, 05:39:15 PM »

that box looks superb . I`ve only got a bit of the original riser - I`m going to PM Robotmay of this Parish to see if his scrap Erika has one on
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Club Modell II
« Reply #52 on: January 16, 2016, 11:21:03 AM »

Pallets now refaced and refitted, one pallet has slightly oversized facing as I was concerned about the coverage of the original (bit close, those corner cut pallets are a pain)

 ............ The hot glue gun is messy but with a "de-whiskering wand" at hand at least the mess stays outside the melodeon - I`m sure many here produce a nicer finish to the glue than I do (or Hohner does even as the Vallenato I had was a right mess) but it must be an art ;) , no matter it does the job, is easily reversible and the thing has a GRILLE :D .
levelling the action isn`t fun with the rather unique unified fingerboard this box has (the top doesn`t come off) especially as its a wood one and easily damaged so I levelled the buttons with it off and refitted afterwards -  I`m looking forward to getting the Erika type one from Rob which will allow me to set the button height perfectly, get a smoother action and have travel limiting felt underneath as this one is like a Pokerwork one but bigger, the buttons disappear and unlike the Corona one , there`s no removable panel underneath :(

« Last Edit: January 16, 2016, 11:23:05 AM by Adam-T »
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Club Modell II
« Reply #53 on: January 16, 2016, 11:37:45 AM »

Not seen those pallets with the corners cut off, very odd.

I would have stripped the bass mech and cleaned the corrosion off myself especially around the pivot area.

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Club Modell II
« Reply #54 on: January 16, 2016, 12:03:21 PM »

I don`t like disassembling mechs unless something is wrong so I just scrubbed the pivot part with a fine wire brush and used graphite powder - same with the rods (though used Emery on the rods themselves) , the action is fine :) .

Another thing I`ve noticed which I`ve not seen before I a Hohner is the bellows gasket, I`ve only seen the rope type on these old boxes, this had 4 strips of thin pallet type leather instead , I thought it may have been redone at some stage but when I came to remove it, it looked totally original and left a lovely clean surface.
« Last Edit: January 16, 2016, 12:33:29 PM by Adam-T »
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Club Modell II
« Reply #55 on: January 16, 2016, 01:13:38 PM »

Interesting those missing corners on the pallets.  My Club Modell 1 had a problem with just those pallets lifting too high and lifting the arms of the pallets on the other row.  Luckily, the fingerboard has a removeable top so I could lay a thin batten and some felt under the levers to restrict the action and still refit the keyboard - but cutting the corners off would have solved the problem, albeit with more work involved.

The trouble with scraping rust off anything ferrous is that it also scrapes off more of the original protective coating.  I was thinking along the lines of reducing the built up rust with a fibreglass brush and then maybe using some rust converter to prevent recurrence.  Perhaps furniture polish to help repell humidity?  All the advice on the forum is to avoid leaving any residue which could hold dust, but I wonder about the guitarists' method of nut lubrication where vaseline is used as a carrier for graphite powder.  If the mix were saturated it might do the trick with minimal potential for holding dust.  I guess there is a difference between the normal practice of a professional restorer who is working on a box which the owner doesn't maintain himself and what may work for an owner who is willing to routinely do some work for optimum performance?

Rob.

Rob.
Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Club Modell II
« Reply #56 on: January 16, 2016, 01:36:31 PM »

The trouble with scraping rust off anything ferrous is that it also scrapes off more of the original protective coating.  I was thinking along the lines of reducing the built up rust with a fibreglass brush and then maybe using some rust converter to prevent recurrence.  Perhaps furniture polish to help repell humidity?

Great ideas Rob but in all fairness, these "Pokerwork" bass mechs are pretty crude and will even work OK when caked with dry rust (they just squeak), and I`d guess that most out there are being played like this happily - LOL ...  I doubt there`s much in the way of protective coating on the metal to begin with and it`d have long gone by now (Hence the rust) , all of the ones I`ve encountered have been rusty to some degree, even pretty newish ones . I scrubbed off the worst near the pivots and dusted with graphite (which probably won`t last long but I doubt it`s had anything done before and was working OK even then) ..

I`ve not seen corner cut pallets before either, but then I`ve never opened a Modele II / Erika before .
« Last Edit: January 16, 2016, 01:38:05 PM by Adam-T »
Logged
Q: How do you cure MAD?
A: Buy more Boxes

playandteach

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3526
  • Currently a music teacher in a high school.
Re: Club Modell II
« Reply #57 on: January 16, 2016, 05:34:13 PM »

Pallets now refaced and refitted, one pallet has slightly oversized facing as I was concerned about the coverage of the original (bit close, those corner cut pallets are a pain)

 ............ The hot glue gun is messy but with a "de-whiskering wand" at hand at least the mess stays outside the melodeon - I`m sure many here produce a nicer finish to the glue than I do (or Hohner does even as the Vallenato I had was a right mess) but it must be an art ;) , no matter it does the job, is easily reversible and the thing has a GRILLE :D .
levelling the action isn`t fun with the rather unique unified fingerboard this box has (the top doesn`t come off) especially as its a wood one and easily damaged so I levelled the buttons with it off and refitted afterwards -  I`m looking forward to getting the Erika type one from Rob which will allow me to set the button height perfectly, get a smoother action and have travel limiting felt underneath as this one is like a Pokerwork one but bigger, the buttons disappear and unlike the Corona one , there`s no removable panel underneath :(
I've just had the same issue - had to find a dewhiskering wand fast in mid job. Having a bit of faff with the key height. The Erika does have a removable keyboard, but the Celluloid part has shrunk, so all buttons are also fouling the sides of the holes in different places either end of the row.
I ended up using fingers to bend rods and things are slightly twisted now - just a patience job I think.
Are wooden retro-fit keyboards likely to be a bigger fit than the old celluloid one?
Logged
Serafini R2D2 GC, Serafini GC accs 18 bass

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Club Modell II
« Reply #58 on: January 16, 2016, 05:49:28 PM »

I`ve never seen a Wooden, plastic or any other kind of retro-fit for these models, if it breaks you have to fix it , bodge it or find another from a donor box .  the Pokerwork style one on mine is original and seems to pre-date the far more sensible celly-topped variety , thankfully another member is supplying me with an Erika one , setting up the keys with the Pokerwork-design one is a nightmare and your fingers disappear in the holes like the regular 2 row boxes :( . No wonder they designed the celly-topped and later on the removable base ones .
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Club Modell II
« Reply #59 on: January 18, 2016, 11:09:15 AM »

Nice clean reedblock - very messy job, the plates are still amazingly "Silvery" for old zinc jobs , Valving and waxing next .. one note, it`s amazing how rough these reedblocks can be, there was split wood into the chamber where a reednail had been fitted badly (now sorted in case it fouled a reed or valve) and more than one nail hole suggesting they`d fitted it badly at first..  these old Hohner blocks are rather well made and far better than some of the early Italian ones which are very poorly made indeed

Note the proper wood wedges for the treble reed voicing (not Wax, putty or chewing gum), and the knobbly bit on the end for an accidental /  proper blocked out chamber for the small acc -no early Italian style wax`n`paper botches here .
« Last Edit: January 18, 2016, 11:11:11 AM by Adam-T »
Logged
Q: How do you cure MAD?
A: Buy more Boxes
Pages: 1 2 [3] 4   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal