Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Surprise inside, "a little knowledge is a dangerous...."  (Read 4665 times)

0 Members and 1 Guest are viewing this topic.

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Surprise inside, "a little knowledge is a dangerous...."
« on: December 12, 2015, 10:58:02 AM »

Several months ago, I purchased a master supertone one row 4stopper, relatively inexpensively from the daughter of a deceased hobby fetter-melodeon collector. The posted pictures looked better than the actual box, when it arrived. There were several parts poorly repainted, but the bellows were good, the pallets were relined with felt only and leaked a lot of air. The big surprise was inside: the leathers had been replaced with pieces of leather cut from a man's belt and attached with epoxy!!!. The good news is that the reeds weren't rusty and appear to be DIX reeds. I reassembled the box, put it on a shelf to dealt with later. I decided to work on it today. I removed one reed and pulled off the inappropriate leather. the epoxy stayed adhered to the zinc reedplate. I used dental tools, pallet knives, and watchmakers screwdrivers to gently remove the epoxy, always working away from the reed tongue. There was a plug of epoxy down on the reedslot, pressing against the reed, about 4mm long. It took me over half an hour get the epoxy out of the slot. I succeeded without damaging the reed. Only forty five reed pairs left to remove epoxy from. Any suggestions for other removal techniques. I had to work under an illuminated magnifier.
« Last Edit: December 12, 2015, 11:03:30 AM by Psuggmog Volbenz »
Logged
I'm squeezin' and they're wheezin': old junker boxes

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #1 on: December 12, 2015, 11:00:44 AM »

A few more pictures: The picture of the cleaned reed shows the long scrape mark on the blued reed tongue. That was from tuning and not from epoxy removal. The bass reeds have the same problem.
« Last Edit: December 12, 2015, 11:05:51 AM by Psuggmog Volbenz »
Logged
I'm squeezin' and they're wheezin': old junker boxes

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #2 on: December 12, 2015, 11:10:40 AM »

Agreed about "a little knowledge is a dangerous...." but even more important , Poor knowledge in any quantity is far more dangerous than a little good advice .  I`ve seen reed plates themselves epoxied in before now - and in the wrong place upside-down, sometimes these boxes are kicked back together to keep them running (Witness the old guy in the 60s with fag-ends as buttons on his Concertina or even our own Pikey using matches for bellows pins and gaffa tape everywhere elee (LOL - I believe Pikey has finally sorted it) 

BUT when they`re doing poor work to sell-ons or collectors pieces like the box you`ve posted above, it`s not good .. I had a HA114 a few years back which had at some stage been "Fettled" by a well known repairer , he`d flooded the whole front end with reedwax to fix leaks around the frame, there was no way it could be removed and a proper job done, he`d not done a good job of refacing the pallets either (merely stuck new felt over the old)  - at least he`d tuned the thing beautifully, maybe he ought to stick to tuning only ..........

this is why this forum is so valuable, all the guy who owned your Epoxied box needed to know was where to get plastic valves and what adhesive to use and you`d have been saved a lot of hassle ..
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #3 on: December 12, 2015, 07:04:31 PM »

When I repair/return these old boxes to playable condition, I try to use the same materials used at the time they were originally made. If that isn't possible I use archival quality materials which  can be removed at a later date without damage. Most of the melodeons I fix up were assembled with hot hide glue, so I use this type of glue if originally used. When I use PVA glue, I use a version which remains flexible and is water soluble.
Logged
I'm squeezin' and they're wheezin': old junker boxes

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #4 on: December 12, 2015, 10:58:23 PM »

Try a single reedplate (in a sealed poly bag) in the deep freeze for long enough to get the temperature down low, this often causes enough contraction of the metal and embrittlement of the glue for it to crack off more easily, you have to be quick 'cos they are small enough to warm quickly. Warm up to get rid of any condensation afterwards.

Nice looking box, good luck with the restoration.
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #5 on: December 12, 2015, 11:10:20 PM »

Thanks for the suggestion. I had thought about using heat , but didn't want to risk changing the temper of the reed tongue.
Logged
I'm squeezin' and they're wheezin': old junker boxes

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #6 on: December 12, 2015, 11:29:18 PM »

No, you generally need 80-100C before epoxy starts to yield any, below blue temper (c 270 - 300C) but so easy to overcook something that small ! As it softens it gets harder to get the 'smear' off, Acetone may help once cool.
If you can get down to -20C it'll do nothing significant to the steel (AFAIK, cryo grain refining is typically liquid Nitrogen cold) and if the perpetrator of this crime didn't pre clean before gluing, it may crack off clean if not anchored in the rougher walls of the slots. Winter is coming, you may live somewhere that you can leave them out on the windowsill over night :o

This is where the museum conservators tend to reach for the ultrasonic probe
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #7 on: December 14, 2015, 05:19:31 AM »

I spent some time on this project today. I have successfully removed all of the epoxy and valves on two banks of treble reeds. The attached pictures show the progress to date and tools used. For the first few valves, I pulled the valves off and then worked on removing the epoxy. Then I tried leaving the leather attached while trying to removed the adhesive. The second technique worked better, resulting in larger pieces of glue coming off at a time. The primary tool used was the smaller pallet knife, followed by the watchmakers screwdriver for cleaning out the reed slot and rivet head. The plastic pallet knife works well for scraping wax off the zinc reedplates.
Logged
I'm squeezin' and they're wheezin': old junker boxes

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #8 on: December 14, 2015, 07:44:44 AM »

You are doing well with this restoration and hope it continues successfully. It is a great thing to bring a nice but ill-fettled box like this back into good playing condition.

It looks like the sliders for the stops have been anchored in the closed position using thumb tacks at the bottom end. What could possibly be the rationale behind that?  :o
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #9 on: December 14, 2015, 11:26:41 PM »

You are doing well with this restoration and hope it continues successfully. It is a great thing to bring a nice but ill-fettled box like this back into good playing condition.

It looks like the sliders for the stops have been anchored in the closed position using thumb tacks at the bottom end. What could possibly be the rationale behind that?  :o

I think that the thumbtacks were used to limit the downward travel of the sliders, the sliders still move upward. If a stop travel limiter is necessary, I will glue in little stop blocks to replace the thumbtacks. Often the knobs can be adjusted to provide the same function.
Logged
I'm squeezin' and they're wheezin': old junker boxes

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #10 on: December 14, 2015, 11:47:39 PM »

Often the knobs can be adjusted to provide the same function.

Yes - that would have been my expectation.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #11 on: December 16, 2015, 07:09:25 AM »

Today's update: I have now removed all the treble reeds and successfully removed all the epoxy from the reed plates without damaging a single reed. All the leathers have been removed. The epoxied on belt leather valves were only applied to the exposed face of the reeds. The side confined on the reed blocks had the original leathers, which were held in place with reed wax. These reeds had never been previously removed. I found putty in the two highest pitched reed block cavities of the vertical reed block. There were fingerprints imprinted in the putty. Since the reeds didn't appear to have been previously removed, this is the first time this putty has seen the light of day for at least eighty years. I have thought about decreasing the area under a given reed to possibly improve the response or timbre of the reed by adding pieces of wood, but I didn't expect to see putty used that way. The next step: clean the reeds and remove all wax from the reed blocks. Then, onto the bass end.
Logged
I'm squeezin' and they're wheezin': old junker boxes

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #12 on: December 16, 2015, 08:05:48 AM »

This is really coming along nicely!

On some instruments, I've seen reed wax used to reduce the chamber volume, but not putty. As you say, it's best to use a small wood wedge, which is the method used on Emmanuel Pariselle's melodeon-building courses.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #13 on: December 16, 2015, 08:31:27 AM »

I`ve seen reedwax used for this also even in old Italian boxes (along with paper and reedwax to make smaller reeds fit larger apertures) but it`s real corner cutting . you can expect this in a klingenthal box however , Putty is an upgrade ! , in fact I`m amazed they bothered at all !
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #14 on: December 16, 2015, 08:40:34 AM »

I`ve seen reedwax used for this also even in old Italian boxes
I've seen it used in modern Italian boxes too; often just a rounded blob of wax which looks as if it's been dripped into place. It's a bu**er because it's easy to get your tools (reed lifter especially) jammed in the wax when working on the reeds.   :o
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #15 on: December 16, 2015, 08:44:20 AM »

I've seen it used in modern Italian boxes too. It's a bu**er because it's easy to get your tools (reed lifter especially) jammed in the wax when working on the reeds.   :o

Even worse in the old boxes because it crumbles into the chamber when the reed lifter hits it and who didn`t think to replace the wax there with wood wedges when waxing the reeds in .. Grrrrr  .. I didn`t realise they were still doing it - the boxes I saw it on were no newer than the 60s
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #16 on: December 17, 2015, 08:22:44 AM »

Tonight I pulled the bass reeds and removed the last of the epoxied-on re-purposed belt leather valves. I made a chart listing all the reed pitches before removing the reeds. On the bass reeds, more than one reed is associated with each key so I silenced all but one push and pull reed for each pitch documentation. On the exposed reeds, I slip a little piece of paper under the reed tongue to keep the reed quiet. I don't want the possibility of adhesive from tape transferring to the reed tongue. On the reeds on the underside of the reed plate, for single reeds, I just temporarily tape down the valve. On the triple-reed plates, I just tape over the reed slots of the reeds I wish to silence, since taping down the valve would stop all the  reeds from sounding. I also included a close up photo of the bass reed frame corner, showing the vestiges of the original cotton cordage gasket. The picture also shows the mitered corner and the cleat inside. The folded and glued edge of the impregnated cloth(buckram?) cover is also evident. The somewhat rough edges of the inside of the bellow are partially visible. I always remove any little bits that look likely to come loose at a later date, to decrease the possibility of these being sucked into a reed.
Logged
I'm squeezin' and they're wheezin': old junker boxes

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #17 on: December 17, 2015, 08:49:13 AM »

I thought about your project yesterday while the dentist was using an ultrasonic  de-scaling tool on my teeth.  Would such a tool be useful in cleaning up reeds?  That are for sale on eBay.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #18 on: December 17, 2015, 09:23:03 AM »

I thought about your project yesterday while the dentist was using an ultrasonic  de-scaling tool on my teeth.  Would such a tool be useful in cleaning up reeds?  That are for sale on eBay.

I have thought about that as well. I wonder if the reed life would be shortened. There is only some many oscillations before failure due to fatigue.
Logged
I'm squeezin' and they're wheezin': old junker boxes

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #19 on: December 17, 2015, 09:25:32 AM »

I must admit that on visits to the dentist I tend to cast my eye around the various tools at his disposal, thinking of applications for melodeon repairs.

So far, I have acquired a number of those little 20mm dia. mirrors attached to impossibly shaped handles; so useful for peeking beneath treble action mechanisms without (sometimes unnecessary) dismantling.

Just thinking about manual descaling tools. Would the be sufficiently hard and sharp to be used as reed scratchers?

Logged
Tuner/repairer, now retired.
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal