Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Surprise inside, "a little knowledge is a dangerous...."  (Read 4653 times)

0 Members and 1 Guest are viewing this topic.

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #20 on: December 17, 2015, 11:22:42 AM »

I must admit that on visits to the dentist I tend to cast my eye around the various tools at his disposal, thinking of applications for melodeon repairs.

So far, I have acquired a number of those little 20mm dia. mirrors attached to impossibly shaped handles; so useful for peeking beneath treble action mechanisms without (sometimes unnecessary) dismantling.

Just thinking about manual descaling tools. Would the be sufficiently hard and sharp to be used as reed scratchers?
Re manual descaling tools: If there is any carbon in the steel alloy, they could be tempered to to what ever hardness you desired. However, the harder the temper, the more brittle the metal becomes. The tool only needs to be slightly harder than the material to be worked, especially considering how little material is being removed in the reed tuning application. I did use a dental tool when removing epoxy from the corners of the reed slot at the rivet end of one the reeds of the accordion mentioned in this thread.
Logged
I'm squeezin' and they're wheezin': old junker boxes

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #21 on: December 17, 2015, 01:01:30 PM »

Dental scaling tools are easy to pick up on Ebay and not too expensive. The cheaper stainless steel tools are just fine for reed work.
I use a single-ended scaling tool (the angled tip slightly reduced in size by filing) for setting the reed tip gap. The tool is good for doing the inside reeds as it is small enough to insert into the reed chambers and the angled tip is thin enough to poke through the reed plate slots as required.

The cheaper quality steel is actually quite good, as it is softer than the reed tongue steel, so it doesn't scratch the tongue.

For example see here.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #22 on: December 17, 2015, 02:00:16 PM »

Not sure of the likely effect of an ultrasonic probe on the reed tongue but for cleaning the plate and slot out should be OK - a different effect likely compared with a reedplate dunked in an u/s bath as there is point cpntact and no liquid to damp the tongue vibration.

Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #23 on: December 17, 2015, 04:48:32 PM »

There shouldn't be any problem with using an ultrasonic probe so long as the reed is supported with a shim whilst working on it, surely?  I used to have a set of dentists tools which were very useful for getting into small detail doing warranty inspections on automotive aircon compressors (failure analysis).  Unfortunately all the engineers used them too (without asking!) and b*ggered them all up.  Now that job's gone I ought to get some more.

I have used a fibreglass pen to remove rust from reeds, though everything needs thorough cleaning afterwards as there are particles of rust and glassfibre everywhere.

I wonder whether Theo would remember - the Preciosa that he rebuilt for me had some sort of setting putty in the two top reed chambers.  Very crudely applied but obviously original and I had to scrape some of it out to allow the reeds to sit flat on the frame, the rivet head interfered with it.  I guess a blob of putty is quicker to apply than a wooden ramp.

Rob.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #24 on: December 17, 2015, 05:02:20 PM »

Putty wedges are very common on the high reeds in older Hohners. A modern equivalent would be to use epoxy putty. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Jack Campin

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 764
    • Jack Campin's Home Page
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #25 on: December 17, 2015, 07:00:28 PM »

I opened this thread wondering if anybody could tell me how to unstick the funny-looking old banknotes glued inside my belAAAARRGHH
Logged
http://www.campin.me.uk/

I can't figure out how to quit but I will no longer check this group and have deleted all shortcuts to it.

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #26 on: December 18, 2015, 12:02:25 AM »

Weimar million mark notes Jack, or is it not a pre war Hohner?  :||:
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #27 on: December 18, 2015, 04:35:37 AM »

A green Sicilian-made one probably   >:E
Logged
Tuner/repairer, now retired.

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #28 on: December 29, 2015, 10:07:13 AM »

I thought about your project yesterday while the dentist was using an ultrasonic  de-scaling tool on my teeth.  Would such a tool be useful in cleaning up reeds?  That are for sale on eBay.

I'm totally convinced that my dentist uses a Dremmel  :o
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Surprise inside, "a little knowledge is a dangerous...."
« Reply #29 on: December 29, 2015, 10:13:00 PM »

I have two different types of cast-off dental drills. one is the old style pulley and belt model which can be powered via a treadle drive or an electric motor. It is some what cumbersome to use due to the resistance to movement imposed by the swivels involved. The other one is a pneumatic model, much more compact and lighter in weight. I modified the compressor out of a medical nebulizer to power the turbine. I have a foot switch for operating the air supply. I have used these drills for routing out cavities for shell inlay in musical instrument pegheads and fingerboards. The air drill would be well-suited for reed tuning compared to the relative slow turning and bulky dremel type tools. I don"t use mine this way because I prefer to scrape/file reeds for tuning purposes. I have seen reedplates nicked/damaged from run-away grind stones.
Logged
I'm squeezin' and they're wheezin': old junker boxes
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal