Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: bass spoon pin replacemet  (Read 1679 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Online Online
  • Posts: 1683
bass spoon pin replacemet
« on: December 14, 2015, 09:52:17 PM »

I'm having to replace the springs on one of the bass spoons on an old HA114 (which I have done many times before), but on this one I've noticed that the pin that holds the spoon/spring/etc together has flattened heads on both ends that are wider than the opening, making it impossible to pull the pin out.  In previous cases, the pins in question only had one end with a flat head and could be pulled out easily, but not sure how to go about it on this one?
Logged
C#/D player

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: bass spoon pin replacemet
« Reply #1 on: December 14, 2015, 10:30:10 PM »

Drill it out carefully, maybe ?
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: bass spoon pin replacemet
« Reply #2 on: December 14, 2015, 10:46:08 PM »

You need to grind one end off the pin. Easy if you have a Dremel tool or similar.
I usually replace with a split pin so that future changes are made easy.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: bass spoon pin replacemet
« Reply #3 on: December 15, 2015, 09:49:13 AM »

I used a needle file. The steel is quite soft and will file easily. At least it was on the Organetto.
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

mselic

  • Hero Member
  • *****
  • Online Online
  • Posts: 1683
Re: bass spoon pin replacemet
« Reply #4 on: December 16, 2015, 05:33:18 PM »

any suggestions on what kind of pin to use as a replacement?
Logged
C#/D player

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: bass spoon pin replacemet
« Reply #5 on: December 16, 2015, 05:50:05 PM »

any suggestions on what kind of pin to use as a replacement?

As Rees said above "I usually replace with a split pin so that future changes are made easy."

mselic

  • Hero Member
  • *****
  • Online Online
  • Posts: 1683
Re: bass spoon pin replacemet
« Reply #6 on: December 16, 2015, 10:25:40 PM »

oops - my apologies!
Logged
C#/D player

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: bass spoon pin replacemet
« Reply #7 on: December 16, 2015, 11:10:11 PM »

cotter pin perhaps more recognisable name if you are West of 'the pond'

 ^
(  )
 ||
 ||
 ||
 ||  as best as ASCII art allows
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Johnniez

  • Good talker
  • **
  • Offline Offline
  • Posts: 51
Re: bass spoon pin replacemet
« Reply #8 on: May 15, 2016, 12:32:50 PM »

any suggestions on what kind of pin to use as a replacement?

Small finishing nail works..:Much easier to fix if you screw it to a board

File off the old pin   install small  finish nail  bend using TWO needle nose pliers

Cut if excess or leave it    ur choice,,,ME   I leave it

Johnnie
Logged
Every Day Is A Great Day
Some Are Better Than Others
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal