Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: New reeds in an old Erica  (Read 2514 times)

0 Members and 1 Guest are viewing this topic.

Andy Next Tune

  • aka Andy Wooles
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1127
  • Melodeon with Accidentals? Make a PI Claim!!!
    • www.shavethedonkey.co.uk
New reeds in an old Erica
« on: December 15, 2015, 10:37:33 AM »

Scanning back through this learned website, a number of people have suggested buying reed blocks from the Hohner Shop in Germany as a good way to switch keys of an old Erica.

But what I couldn't see was any comments on the state of tuning of such reed blocks, and therefore the level of tuning work needed once installed.
Are they 'on pitch', sharp, consistent or all over the place? Do they arrive tuned with a Hohner default tremelo, whatever that may be?

I'm just trying to get my head around the different options. The other routes being to salvage and install the reeds from another Hohner, or buy and install brand new reeds from Harmonikas.

I'm aware my key choice favours certain routes - C/F lots of cheap boxes on ebay.de whereas D/G probably means using Harmonikas reeds.
Logged
Andy, from the now ex-County Palatine of Cheshire

Caring for a European community of melodeons from France, Italy, Germany, Wales and Suffolk!

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: New reeds in an old Erica
« Reply #1 on: December 15, 2015, 10:44:00 AM »

The Hohner Shop blocks arrive in standard Hohner tune ie in desperate need of setting up and  tuning.   (:)

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: New reeds in an old Erica
« Reply #2 on: December 15, 2015, 11:43:13 AM »

Just the same as if they had installed them in a Pokerwork and sold it!

Rob.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: New reeds in an old Erica
« Reply #3 on: December 15, 2015, 12:01:40 PM »

If you have a set of DG reeds that you can salvage from an old Hohner that will give you the best result, even if a few reeds have to be replaced.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: New reeds in an old Erica
« Reply #4 on: December 15, 2015, 01:29:54 PM »

Or if you are feeling adventurous hows about using a C/F set and converting to D/G. The 4th or 5th attempt is relatively easy  >:E

Andy Next Tune

  • aka Andy Wooles
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1127
  • Melodeon with Accidentals? Make a PI Claim!!!
    • www.shavethedonkey.co.uk
Re: New reeds in an old Erica
« Reply #5 on: December 15, 2015, 08:31:13 PM »

The box is C/C#, which is why I'm looking to start from somewhere else!!!

Its also an opportunity to have a go at some new skills.
« Last Edit: December 15, 2015, 08:38:21 PM by Andy Next Tune »
Logged
Andy, from the now ex-County Palatine of Cheshire

Caring for a European community of melodeons from France, Italy, Germany, Wales and Suffolk!

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: New reeds in an old Erica
« Reply #6 on: December 15, 2015, 09:44:47 PM »

I have found that converting a C/C# set to D/G with button 4 start is almost easier than Lester claims for reworking a C/F set.  >:E






« Last Edit: December 16, 2015, 01:01:22 PM by Malcolm Clapp »
Logged
Tuner/repairer, now retired.

Jackdaw

  • Castagnari Lilly d/g Erica d/g - Pokerwork d/g Castagnari c#/d - Pokerwork c - Lachenal ENG Concertina - Anglo Concertina
  • Member
  • *
  • Offline Offline
  • Posts: 34
Re: New reeds in an old Erica
« Reply #7 on: December 16, 2015, 01:04:55 AM »

I converted my C/F Erica to D/G I only retuned and used one single reed set..got it close then I took an old set of D/G reeds from an old Pokerwork and also fitted them to mask any off tuning.The result... an almost dry slight tremolo sweet tone..also fitted a strip of padded wood under the keys to stop travel..I love Erica. It was worth it...I also fear the dreaded factory Hohner tuning..
Wish you luck with it.
Jack
Logged
Too old to be a Morris minor

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: New reeds in an old Erica
« Reply #8 on: December 16, 2015, 05:11:33 AM »

I would doubt that new Hohner factory-tuned reeds would be any more out of tune than a set from a well-used older melodeon with high miles on the clock. Sadly, customer expectations are often high, but rarely met, and a bit of fine tuning is usually essential.
« Last Edit: December 16, 2015, 07:02:53 AM by Malcolm Clapp »
Logged
Tuner/repairer, now retired.

Andy Next Tune

  • aka Andy Wooles
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1127
  • Melodeon with Accidentals? Make a PI Claim!!!
    • www.shavethedonkey.co.uk
Re: New reeds in an old Erica
« Reply #9 on: December 16, 2015, 09:35:26 AM »

I have found that converting a C/C# set to D/G with button 4 start is almost easier than Lester claims for reworking a C/F set.  >:E
Interesting! Think I need to look at the conversion paths from both C/C# and C/F reed sets much more closely.
Logged
Andy, from the now ex-County Palatine of Cheshire

Caring for a European community of melodeons from France, Italy, Germany, Wales and Suffolk!

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: New reeds in an old Erica
« Reply #10 on: December 16, 2015, 02:37:07 PM »

I have found that converting a C/C# set to D/G with button 4 start is almost easier than Lester claims for reworking a C/F set.  >:E
Interesting! Think I need to look at the conversion paths from both C/C# and C/F reed sets much more closely.

Just to give you a starting point for the conversion from C/C#, I would suggest tuning up by a semitone all but the first button reeds of the C# set to D and transfering those reeds to the old C block, starting with the third chamber which will now sound A/C#. (D/E will be your 4th button start.)

For the first 2 chambers at the chin end of the D row, where many possibilities are available according to your taste (accidentals, low notes or a mix of both) you may need to "import" reeds, but see comment below*. (Same will apply to the G row)

Now the fun starts....


Reed 4 (from the C row) (E/F) will need to be repitched to D/F# and mounted in chamber 3 (of your new G row)
Reed 5 (G/A) is useable as is and mounted in chamber 4
Reeds 6 and 7 just need reversing without repitching and mounted in chambers 5 and 6
Reed 8 G/F needs to be retuned to G/F# and mounted in chamber 7
Reed 9 C/A needs to be retuned to B/A and mounted in chamber 8
Reed 10 E/B needs to be retuned to D/C and mounted in chamber 9
Reed 11 G/D needs to be retuned to G/E and mounted in chamber 10

Apart from the last mentioned, nothing has to be sharpened by more than a semitone (easily achievable). You may be better off though importing the high G/E as these high notes can be difficult to sharpen by a full tone, though not impossible.

Some notes will need to be flattened. Your choice, filing or weighting. Personally, I would go with the latter as the small amount of solder needed will not appreciably slow down the reed response in my experience.

At this point, you should have 4 pairs of reeds left over (one from the old C# row and 3 from the old C row), and 4 empty chambers. You might be able to use some of these reeds for retuning to low notes you need in these chambers, depending what you decide you would like as mentioned above*. Accidentals, if required, will need to be imported though.

I'll maybe let some one else chime in regarding the conversion from C/F (Lester??) as it's getting past my bedtime....(yawn emoticon). Ditto the left hand.

Hope this helps, and good luck. (All care taken; no responsibility accepted!)



 
Logged
Tuner/repairer, now retired.

Andy Next Tune

  • aka Andy Wooles
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1127
  • Melodeon with Accidentals? Make a PI Claim!!!
    • www.shavethedonkey.co.uk
Re: New reeds in an old Erica
« Reply #11 on: December 16, 2015, 03:09:31 PM »

Brilliant, Malcolm. That's a great help.
Logged
Andy, from the now ex-County Palatine of Cheshire

Caring for a European community of melodeons from France, Italy, Germany, Wales and Suffolk!

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: New reeds in an old Erica
« Reply #12 on: December 17, 2015, 12:14:05 AM »

Just to add that you will need to reduce the height of most of the reed chambers to accommodate these repositioned reed plates.

I glue pieces of wood into the top of the chambers to achieve this, which also reduces the volumetric size of the chamber to best suit the new (higher) reed pitches in each chamber.
Logged
Tuner/repairer, now retired.
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal