Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Wit's End  (Read 3850 times)

0 Members and 1 Guest are viewing this topic.

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Wit's End
« on: May 31, 2009, 06:48:19 AM »

 Ok, it's a pesky reed. I only have one wit left, and I am at the end of it!
 Here's the background: The instrument is an Italian made organetto in Sol (G), almost new, 9+4 keyboard with 4 basses. Has 2 medium reeds in tremolo, also has a stop for one set of low reeds.

When I play my middle of keyboard G (push), some times the reed tuned to pitch sounds about 5 cents flat. The other G reed, tuned at approx +12, is fine. If I press the bellows harder (harder than I normally play), the flat note returns to it's correct pitch. It will remain there, no matter how many times I play it, or how loud or soft, and remain in perfect tune only if I do not play the Pull note on that key (F#). If I do that, then the G pitch reed sounds flat again when played. (The +12 reed plays fine always).

Sounds like this could be not so hard to figure, but let me outline what I have done thus far:
(each attempted repair yielded no change)

Examined the reed and plate carefully with a hi-powered magnifier,
Cleaned under the reed tongue for debris or lint, checked the outer valve thoroughly (these are ventili made of mylar)
Gently lifted the reed and looked at the back of the valve on the back side, checked the alignment of the tongue in  the  reed frame,
Re-set the reed to speak exactly when it's +12 mate sounded,
Removed the reed from the box (they are mounted flat to the soundboard, no reed 'block') to examine the valve on the back side of the reed plate, having speculated that it was not opening and closing freely, affecting the pitch. It was fine, nothing rubbing, no stray wax or sticky stuff, no bugs.
Replaced the reed and rewaxed it in.............No improvement. Push hard, and it's in tune, pull the F# and the G reed goes flat. And yes, I made certain I wasn't messing with the wrong reed.
  So, there it is. And I really love this little box, the other reeds behave quite nicely and sing happily in tune all the time. I am hoping that the collective wisdom of all the  professors of reed physics out there might have some obvious answer or at least a hypothesis that they can share. If it's a bum reed, well then, I can always get another and perform a transplant,  but I am willing to hear any and all theories. Thanks for taking the time to read this! Best wishes............jwf 
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Wit's End
« Reply #1 on: May 31, 2009, 08:40:49 AM »

Very well described, very strange and very annoying. No wonder you are at your wits end.
Others better qualified than me may well reply to you with advice, but to me with a little knowledge (whilst acknowledging this may be a dangerous thing) it seems as if you have done all the correct things so far.

The crucial factor seems to be the excess bellows pressure required to get the reed sounding in tune, coupled with the fact that it remains in tune so long as you do not reverse the bellows direction on that same button.

To me, this sounds like a valve problem. You have already indicated that the valve looks OK, but it still (for some inexplicable reason) may not be performing correctly. Under normal push bellows pressure, either the valve on the underside of the offending reed is not opening properly, or its mate on the F-sharp reed is not closing properly. Or the G-reed valve may be a rogue, with some freak acoustic property which is setting up a sympathetic vibration of its own and forcing a flat response. My advice would be to replace the valve on the underside of the problematic G-reed, and maybe the valve on the F-sharp reed too. They're cheap enough to replace, if a little bit fiddly, but it seems the only thing you haven't tried so far, and it could just do the trick.

Good luck!
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Wit's End
« Reply #2 on: May 31, 2009, 09:38:51 AM »

I agree with Steve.  Its the valve on the back of the misbehaving reed,   something that may be too small to see is causing it to fail to open fully under certain conditions.   
Two possibilities:
  • some sticky contamination under the valve is holding it down till you increase the pressure
  • the valve is getting caught up on the inside edge of the reed chamber.  You can check for this by looking into the vent in the base of the reedblock while depressing the reed tongue,  the valve should open and close freely.

Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

xgx

  • Bagpipes & Musette Boxes... and Banjos, luv 'em!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1157
Re: Wit's End
« Reply #3 on: May 31, 2009, 11:24:56 AM »

I'm still trying to work out the mysteries of the outside of the box.... let alone the inside ::)

Theo/Steve any chance of a pic which identifies the  'valve' / 'reed tongue' / etc. please?
Logged
Graham

Socio-Demographic:   Graduate, Coffin Dodger
 Location: N Cambs/S Lincs - UK

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Wit's End
« Reply #4 on: May 31, 2009, 11:53:31 AM »

If you need a photo to tell the difference between the reed tongue (steel), and a valve (leather or plastic), then you'd better stay away from the insides of your box!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Wit's End
« Reply #5 on: May 31, 2009, 05:00:13 PM »

Very well described, very strange and very annoying. No wonder you are at your wits end.
Others better qualified than me may well reply to you with advice, but to me with a little knowledge (whilst acknowledging this may be a dangerous thing) it seems as if you have done all the correct things so far.

The crucial factor seems to be the excess bellows pressure required to get the reed sounding in tune, coupled with the fact that it remains in tune so long as you do not reverse the bellows direction on that same button.

To me, this sounds like a valve problem.

I agree with Steve.  Its the valve on the back of the misbehaving reed,   something that may be too small to see is causing it to fail to open fully under certain conditions.   
Two possibilities:
  • some sticky contamination under the valve is holding it down till you increase the pressure
  • the valve is getting caught up on the inside edge of the reed chamber.  You can check for this by looking into the vent in the base of the reedblock while depressing the reed tongue,  the valve should open and close freely.




Good luck!
Hello Theo and Steve, thanks for your reply! I fully agree that this could be the only logical cause for this condition, since the reed cannot change length or mass arbitrarily. It could go sharp if the reed was somehow obstructed by the frame or debris, but flat? Has to be an airflow issue.

Anyway, there is no way to view the action of the valve in question as the reeds are waxed directly to the sound board, and would require the removal of a pallet to see into the reed chamber, and my dental mirror won't even work for this. As an aside, if I press the affected key and verrry gently move the bellows back and forth, lightly enough so that the reeds are not sounding yet, I can hear the ventili doing their job of opening and closing. Clack clack.

 I do like Steve's "rogue valve" theory, though. As much as I dislike doing so, I will remove the reed plate again and replace the valve, as I have a few new mylar units put aside. I will report on the outcome of this attempt, but as I have spent too much time with my head inside this box, I have some gardening to attend to today.  Best wishes to you, and may your reeds sing well!!
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Wit's End
« Reply #6 on: May 31, 2009, 05:54:14 PM »

As much as I dislike doing so, I will remove the reed plate again and replace the valve, as I have a few new mylar units put aside. I will report on the outcome of this attempt, but as I have spent too much time with my head inside this box, I have some gardening to attend to today.  Best wishes to you, and may your reeds sing well!!
Following on from Theo's advice - while you have the reed plate off, check that the inside of the reed chamber is smooth and there are no projecting splinters of wood or anything else which could foul the valve when you replace it. 
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Wit's End
« Reply #7 on: May 31, 2009, 06:27:38 PM »


Following on from Theo's advice - while you have the reed plate off, check that the inside of the reed chamber is smooth and there are no projecting splinters of wood or anything else which could foul the valve when you replace it.  

I will certainly do so and I am grateful for your and Theo's help......All the best to you!!
« Last Edit: May 31, 2009, 07:52:10 PM by j.w.forrest »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Wit's End
« Reply #8 on: May 31, 2009, 08:03:53 PM »


Anyway, there is no way to view the action of the valve in question as the reeds are waxed directly to the sound board,

There is one other way to check the valve.  Press down on the reed tongue so that it contact with and lifts the valve.  If the valve is stuck, or is brushing the edge of the reed chamber you should be able to hear it.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Wit's End
« Reply #9 on: May 31, 2009, 10:45:09 PM »

 
[/quote]

 If the valve is stuck, or is brushing the edge of the reed chamber you should be able to hear it.
[/quote]

Right you are, Theo....I detected a slight skritching noise....I reset the offending valve and then gently lifted the reed, prodded the back of the valve with a bit of wire, and sure enough, it is being restrained by either the end of the chamber or by the edge. Of course if I play those two notes a few thousand times, maybe the valve will 'wear in' as it were, but I think my family would move out long before..... ;D I will undertake to remove the reedplate again, and see if I can make things swing clear. In the meantime, I can certainly appreciate you sharing your professional skills, which only come from long practice and experience. And thanks also to Steve for his assistance. Hope to encounter you folks some day, if I ever make it to your fair land..........jwf
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal