Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Rotello screw pin sliding out  (Read 2134 times)

0 Members and 1 Guest are viewing this topic.

Sandy Flett

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
    • Accordion and Melodeon Blog
Rotello screw pin sliding out
« on: January 13, 2016, 04:25:39 PM »

As shown in the attached photo, the pivot pin for the rotello screw on my Baffetti Carnival II bass strap keeps sliding out. Any ideas for how I can fix this?
Logged
DG Dino Baffetti Carnival II (plus accordions)
Accordion and Melodeon blog

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Rotello screw pin sliding out
« Reply #1 on: January 13, 2016, 04:29:07 PM »

Sorted this very problem recently thusly:

Push pin back into place
Put a couple of stitches with thick cotton through the opening on both sides to close up the opening (I used a 1mm drill to make the holes)
Screw the rotello back in place

Settle back with smug look of success :)

Sandy Flett

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
    • Accordion and Melodeon Blog
Re: Rotello screw pin sliding out
« Reply #2 on: January 13, 2016, 04:32:54 PM »

Brilliant. Thanks, Lester.
Logged
DG Dino Baffetti Carnival II (plus accordions)
Accordion and Melodeon blog

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Rotello screw pin sliding out
« Reply #3 on: January 13, 2016, 04:42:18 PM »

Push pin into one side, strike empty side gently with hammer. Hammer pin back into place. You now have an interference fit.

Sir John
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Rotello screw pin sliding out
« Reply #4 on: January 13, 2016, 05:12:17 PM »

Or a couple of drops of superglue where the pin fits through the hole in the screw.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Foma

  • Member
  • *
  • Offline Offline
  • Posts: 21
    • Гармонь
Re: Rotello screw pin sliding out
« Reply #5 on: January 13, 2016, 05:12:33 PM »

Logged

Sandy Flett

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
    • Accordion and Melodeon Blog
Re: Rotello screw pin sliding out
« Reply #6 on: January 13, 2016, 05:28:47 PM »

A variant of John's suggestion seems to have worked - I fitted the pin into position then gave the two rivets a few taps with a hammer (on my vice). The ends look more closed up and moderate pressure did not move the pin. I will keep an eye on it. Thanks all.
Logged
DG Dino Baffetti Carnival II (plus accordions)
Accordion and Melodeon blog

Ebor_fiddler

  • Chris
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2340
  • Hohner 1040 C One-Row, Sandpiper D/G, Liliput C/F
    • Ebor Morris
Re: Rotello screw pin sliding out
« Reply #7 on: January 14, 2016, 12:07:58 AM »

Oh - THAT'S what it's called ...
Logged
I'm a Yorkie!
My other melodeon's a fiddle, but one of my Hohners has six strings! I also play a very red Hawkins Bazaar in C and a generic Klingenthaler spoon bass in F.!! My other pets (played) are gobirons - Hohner Marine Band in C, Hohner Tremolo in D and a Chinese Thingy Tremolo in G.

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Rotello screw pin sliding out
« Reply #8 on: January 15, 2016, 07:13:26 AM »

I agree with the superglue ,but if you want to get all fancy... Turn new pin on lathe for a press fit into screw ,heat screw to about 400-450F chill pin on block if dry ice, using gloves put screw in slot and using pliers quickly push in into screw, chill screw with wet rag. Should stay in pretty good now.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Rotello screw pin sliding out
« Reply #9 on: January 15, 2016, 09:54:24 AM »

[quote author=Kimric Smythe link=topic=18125.msg222433#msg222433 date=1452842006?.. if you want to get all fancy... Turn new pin on lathe for a press fit into screw ,heat screw to about 400-450F chill pin on block if dry ice, using gloves put screw in slot and using pliers quickly push in into screw, chill screw with wet rag. Should stay in pretty good now.
[/quote]
If you go the "turn a new pin" route, I suggest using a foot treadle lathe similar to my old Shepard.
Logged
I'm squeezin' and they're wheezin': old junker boxes

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Rotello screw pin sliding out
« Reply #10 on: January 15, 2016, 11:25:10 AM »

Lovely machine.  A friend has a very similar one.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Rotello screw pin sliding out
« Reply #11 on: January 17, 2016, 12:25:42 AM »

If we're looking at technical solutions, then removing the pin and knurling the centre section will also make it an interference fit.  Superglue's quicker though.

I also had a friend (long gone now) who had a similar treadle lathe in his shed.  I couldn't believe he intended to remove the treadle drive and fit an electric motor.  Nor did he remember to leave it to me, sadly.

Rob.
Logged

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: Rotello screw pin sliding out
« Reply #12 on: January 17, 2016, 12:50:37 AM »

Thats a shame Rob, lovely lathe Psuggmog.
My 1917 Drummond was left by a friend who wanted it to continue to make and repair steam engines, while adding a 3 phase motor & variable speed / reversing inverter using existing tappings to mount the frame on (and poly vee belts run very wel on cambered pulleys for leather belts !) the treadle remains intact as it is very handy for picking up coarse threads in wood if using hand chasers, although the knees seem to be getting less and less happy with extended periods on the one legged jogging machine.
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Rotello screw pin sliding out
« Reply #13 on: January 17, 2016, 12:53:02 AM »

If we're looking at technical solutions, then removing the pin and knurling the centre section will also make it an interference fit.  Superglue's quicker though.

I also had a friend (long gone now) who had a similar treadle lathe in his shed.  I couldn't believe he intended to remove the treadle drive and fit an electric motor.  Nor did he remember to leave it to me, sadly.

Rob.
Its often more common to find the old treadle lathes missing the treadle drive due to electric motor retrofit. Usually the treadle parts were scrapped. It was also possible to order some makes with a "velocipe drive" or set up for lineshaft power.
Logged
I'm squeezin' and they're wheezin': old junker boxes

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Rotello screw pin sliding out
« Reply #14 on: January 17, 2016, 04:26:36 PM »

I used to use a little Unimat for everything till the Safe shop next door to me closed, the owner gave me the 1930's South Bend lathe that they had and would not take any money for it, I gave him a bottle of my moonshine.
 The unimat is great for stuff around the shop.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Rotello screw pin sliding out
« Reply #15 on: January 17, 2016, 09:48:30 PM »

I used to use a little Unimat for everything till the Safe shop next door to me closed, the owner gave me the 1930's South Bend lathe that they had and would not take any money for it, I gave him a bottle of my moonshine.
 The unimat is great for stuff around the shop.
I have a 1930s Southbend as well, I bought it forty years ago and still use it regularly. I converted it to foot power because at the time, I couldn't find a treadle lathe to buy. I machined a 30 pound flywheel and mounted it on the countershaft, added a bicycle freewheel to the flywheel. A roller chain goes from the treadle bar over the sprockets to a tension return spring. This system works better for me than the conventional treadle because I eliminated the main shortcomings of the treadle system: top dead center starts, unintentional reverse direction starts and the possibily of crushing foot injuries from the fixed drive treadle bar. I never considered a unimat, it seemed too light for anything I would want to do. I have a german made watchmakers lathe for really tiny stuff.  It is good to hear that the unimat works for you.
« Last Edit: January 17, 2016, 09:52:57 PM by Psuggmog Volbenz »
Logged
I'm squeezin' and they're wheezin': old junker boxes
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal