Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Re- waxing with or without pins.  (Read 5429 times)

0 Members and 1 Guest are viewing this topic.

Henry Piper

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 368
Re- waxing with or without pins.
« on: January 15, 2016, 09:55:10 AM »

Hello.
I am about to re-valve and re-wax a Hohner single Row melodian, As you are all aware the treble reeds are Flat mounted directly on the rear of the Palette Board, and are fixed by dome shaped pins between each plate as well as waxed in place. Some people have suggested that the pins are not needed, and should be scrapped, what would the consensus of the Experts on here be ??
Logged
From Ottery St Mary Devon. Currently Playing Dino Baffetti BP2 in D/G, Hohner Student 1 P.A conversion  in D/G,  Hohner 3515 Pre-Pokerwork in A/D,   2 row "Beaver Brand" in Bb/Eb, Hohner Pre- Erica in G/C .  Single row permanent 4 voice, 4 bass in C from old Hohner single row and bits of a cheap Cajun box !!,

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Re- waxing with or without pins.
« Reply #1 on: January 15, 2016, 10:21:32 AM »

I have a pot containing a fair number of Hohner reed pins; personally I've never bothered to put any of them back after a rebuild, and so far I've had no problems with reeds held in purely by wax. I don't know, but I imagine very few, if any, modern boxes use pins as well as wax, as they're just not necessary. Other opinions may vary.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: Re- waxing with or without pins.
« Reply #2 on: January 15, 2016, 10:32:06 AM »

I also have a pin pot now, after starting to learn how to wax. I found it much harder to wax with the pins in place, though that might just be a failure in my technique.
Logged

benammiswift

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 158
  • Squeezing for Derbyshire
    • benammiswift.co.uk
Re: Re- waxing with or without pins.
« Reply #3 on: January 15, 2016, 11:15:49 AM »

I had Theo Gibb do some old reed blocks of a Club for me and he removed all the pins son I guess that means they are unnecessary. I've never seen wax and pins used together apart from that, I've seen just pins and just wax. Pins tend to be used on modern reed block made of different material such as aluminium reed blocks as the wax may not transfer the sound properly.


Benammi
Logged
Castagnari Handry 18

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Re- waxing with or without pins.
« Reply #4 on: January 15, 2016, 11:18:40 AM »

I used to have a pot full of pins now I just bin them straight away. Just wax for me.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Re- waxing with or without pins.
« Reply #5 on: January 15, 2016, 11:26:26 AM »

As above, and Hohner have not used pins on new reed blocks for many years.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Re- waxing with or without pins.
« Reply #6 on: January 15, 2016, 12:26:16 PM »

I generally haven't used pins for some years, the exception being on Hohner 1140's, which it seems is the model the op is referring to. My experience is that this model tends to suffer more loose treble reed problems than any other by a considerable margin. Maybe I'm just being overly cautious, and out of step with everyone else, but my recommendation to the op would be to use pins, just to be on the safe side. The weight and time saving is insignificant (less than 5 minutes and not much more than 10 grams), so I can't really see any objection to it.

As for waxing with the pins in place, it has never occurred to me to try that! I add the pins after the waxing, but while the wax is still slightly soft. Just a firm push with the face of on old, worn-out flat file does the job. (No club hammers please, not even on Club models....)
« Last Edit: January 15, 2016, 12:31:06 PM by Malcolm Clapp »
Logged
Tuner/repairer, now retired.

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: Re- waxing with or without pins.
« Reply #7 on: January 15, 2016, 01:25:24 PM »

As for waxing with the pins in place, it has never occurred to me to try that! I add the pins after the waxing, but while the wax is still slightly soft. Just a firm push with the face of on old, worn-out flat file does the job. (No club hammers please, not even on Club models....)

I tried it as I didn't want to make even more holes; I couldn't find the existing ones once I'd poured the wax over them. I gave up in the end though ;D
Logged

Henry Piper

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 368
Re: Re- waxing with or without pins.
« Reply #8 on: January 15, 2016, 01:36:04 PM »

Thanks everyone,  Yes, it is a 1140, the overwhelming consensus seems to be ,  the pins are irrelevant, so I shall discard them, and just rely on the wax.
Logged
From Ottery St Mary Devon. Currently Playing Dino Baffetti BP2 in D/G, Hohner Student 1 P.A conversion  in D/G,  Hohner 3515 Pre-Pokerwork in A/D,   2 row "Beaver Brand" in Bb/Eb, Hohner Pre- Erica in G/C .  Single row permanent 4 voice, 4 bass in C from old Hohner single row and bits of a cheap Cajun box !!,

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Re- waxing with or without pins.
« Reply #9 on: January 15, 2016, 02:38:28 PM »

I generally haven't used pins for some years, the exception being on Hohner 1140's, which it seems is the model the op is referring to. My experience is that this model tends to suffer more loose treble reed problems than any other by a considerable margin. Maybe I'm just being overly cautious, and out of step with everyone else, but my recommendation to the op would be to use pins, just to be on the safe side.
<snip>

In my mind this is a good reason to not have pins. If the wax is so shot that the pins are what is holding the reed plates in place it would be better for them to fall out and thus trigger a 'proper' repair.

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Re- waxing with or without pins.
« Reply #10 on: January 15, 2016, 03:06:14 PM »

Agreed 100% Lester ! ...
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Henry Piper

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 368
Re: Re- waxing with or without pins.
« Reply #11 on: January 15, 2016, 04:26:44 PM »



In my mind this is a good reason to not have pins. If the wax is so shot that the pins are what is holding the reed plates in place it would be better for them to fall out and thus trigger a 'proper' repair.
[/quote]

The wax is indeed "Shot" and its only the pins holding the reeds in place, The rattle of loose reeds drowns out the sound of the reeds speaking !!  Hence the need for new wax and valves.
Logged
From Ottery St Mary Devon. Currently Playing Dino Baffetti BP2 in D/G, Hohner Student 1 P.A conversion  in D/G,  Hohner 3515 Pre-Pokerwork in A/D,   2 row "Beaver Brand" in Bb/Eb, Hohner Pre- Erica in G/C .  Single row permanent 4 voice, 4 bass in C from old Hohner single row and bits of a cheap Cajun box !!,

AirTime

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 979
Re: Re- waxing with or without pins.
« Reply #12 on: January 15, 2016, 06:53:49 PM »

So ... does waxing rather than pinning effect the sound produced? I have an old Hohner with leather gaskets & pins. The reeds plates are not that securely pinned - they have a tendency to move around a little causing them to sound out of tune at times. This could probably be fixed by finding new pins that would hold in the wood more securely. However, would I be better off just waxing the reeds in position in the "modern" fashion (ie. post-1930)?
Logged
1920's BbEb Hohner; 1920's  AD Koch; 1910 (?) One-row Hohner in D,  1910's GCB Maga Ercole; ; AD 1950's Pistelli, CF Sandpiper, CF Preciosa, BbEb Preciosa.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Re- waxing with or without pins.
« Reply #13 on: January 15, 2016, 06:58:01 PM »

So ... does waxing rather than pinning effect the sound produced? I have an old Hohner with leather gaskets & pins. The reeds plates are not that securely pinned - they have a tendency to move around a little causing them to sound out of tune at times. This could probably be fixed by finding new pins that would hold in the wood more securely. However, would I be better off just waxing the reeds in position in the "modern" fashion (ie. post-1930)?

If the reeds are on a soft leather gasket pinning (or more normally screwing) them is sufficient. Personally, if it's an old Hohner the gasket may well be a bit crispy and hard to get a good seal on so I would probably remove the gasket and wax the reeds in place, but it's a judgement call.
.

AirTime

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 979
Re: Re- waxing with or without pins.
« Reply #14 on: January 15, 2016, 08:56:58 PM »

It's a bit hard for me to judge how soft/crispy the leather is. The pins themselves are certainly a problem, as a few of them are a bit loose so the plates are not really firmly held down. They should probably be replace by a little bit larger screws that would hold better. However, waxing them in would ensure every thing's snug ... but, would this alter the vintage Hohner sound at all?
Logged
1920's BbEb Hohner; 1920's  AD Koch; 1910 (?) One-row Hohner in D,  1910's GCB Maga Ercole; ; AD 1950's Pistelli, CF Sandpiper, CF Preciosa, BbEb Preciosa.

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Re- waxing with or without pins.
« Reply #15 on: January 15, 2016, 10:28:51 PM »

I generally haven't used pins for some years, the exception being on Hohner 1140's, which it seems is the model the op is referring to. My experience is that this model tends to suffer more loose treble reed problems than any other by a considerable margin. Maybe I'm just being overly cautious, and out of step with everyone else, but my recommendation to the op would be to use pins, just to be on the safe side.
<snip>

In my mind this is a good reason to not have pins. If the wax is so shot that the pins are what is holding the reed plates in place it would be better for them to fall out and thus trigger a 'proper' repair.

I wasn't suggesting relying just on the pins; of course the wax would need replacing if it is "shot", but surely the addition of pins would better secure the reedplates to the frame, which I would see as an integral part of a "proper" repair. Maybe a bit of a "belt and braces" approach, but I really can't see the harm....
Logged
Tuner/repairer, now retired.

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Re- waxing with or without pins.
« Reply #16 on: January 15, 2016, 10:45:25 PM »

It's difficult to say whether there would be a difference in tone between secure pinning on a gasket against waxing direct to the wood.  The only thing that crossed my mind is that the Pariselle boxes' reeds are screwed onto a gasket and to my cloth ears they don't appear to have a particularly different tone to that of a high-end Italian box, which is waxed.  Mind you, the ancient chemnitz i have has long plate reeds nailed/screwed to a gasket and has a very diffreent sound, but I would attribute that to the reed type and the rather convolute air passages.

If you really want to know, you'd have to experiment - which means doing the job twice!  if you chose the current norm and wax them in it'll sound fine.

Rob.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Re- waxing with or without pins.
« Reply #17 on: January 16, 2016, 01:18:22 AM »

I generally put them back. If I'm restoring it, I'm 'restoring' it. Also, with brittle wax they stop the plate from dropping out altogether, if  a plate is loose. I imagined they help the sound transfer from the reed plate to the block and decided there was a marginal difference with the pins in place. But looks like I am I a minority (:)

gettabettabox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 684
Re: Re- waxing with or without pins.
« Reply #18 on: January 16, 2016, 01:33:40 AM »

i put them back. 90% in original holes after waxing!
my tribute to what was there before i interfered.
i don't know much about the science of sound, but i reckon that i know a good old hohner sound and i think that if the underside of the domed pin touches... and ''feeds the top of reed plate to the block... and also to it's neighbour,''.... then got to be good.
(has anyone got within their overflowing tubs of hohner pins, a straight one with a horizontal dome?!)   (:)

(science can often be rocked by art)


« Last Edit: January 16, 2016, 01:40:18 AM by gettabettabox »
Logged

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Re- waxing with or without pins.
« Reply #19 on: January 16, 2016, 02:18:25 AM »


...they stop the plate from dropping out altogether, if a plate is loose.


Good point, Roger. Could prevent the possibility of a bit of bellows damage....  ;)
Logged
Tuner/repairer, now retired.
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal