Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Flat mount reed orientation  (Read 4431 times)

0 Members and 1 Guest are viewing this topic.

penn

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 574
Flat mount reed orientation
« on: February 09, 2016, 05:13:36 PM »

I restarted work on an old Koch 1 row that I'd had in pieces two years ago and put to one side.
It's a 2 reed treble, 4 bass, with all flat mounted reeds a bit like a Hohner 1040 I suppose.
Once I'd found all the bits to put the bass end reeds back in I had a dilemma over which way round they were supposed to be.
The pallets holes are placed very definitely at one end of the chamber, and after chewing over the logics, it felt best to fit the reeds with the open ends over the pallet holes - they would surely respond quicker to movements of air?
I'd numbered the reeds to help me work out how to put them back in, but my numbering didn't make sense. Then I found a picture I'd taken when the box arrived, and the RIVET end of the reeds were all plainly over the holes.

Is there a wrong and right way, and a reasoning for placing the reed rivets over the holes? In the end I put them back as per the picture - rivets over the holes and they sound OK.
The picture doesn't show the holes but they were at the bottom of the chamber for the chord reeds, and there are two big holes towards the centre, one hole for each pair of bass reeds.

any comments gratefully received.
Steve

Logged
Hohners, Dino Baffetti, Lilly, Benny + a lot of junk.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Flat mount reed orientation
« Reply #1 on: February 09, 2016, 05:23:02 PM »

I think every reed* I have ever seen has had the rivet end nearest the pallet hole. Consider normal reed blocks the reeds are fitted with the rivets down on the soundboard end.

* Some really small reeds are sometimes fitted the other way round.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Flat mount reed orientation
« Reply #2 on: February 09, 2016, 06:13:17 PM »

Most reeds work best with the tip of the reed at the far end from the opening, whether mounted flat or on a conventional block.  The only exception is some high pitch reeds which respond better and produce more volume when reversed. On a typical treble reed bank you might find the highest two reed plates reversed. On an upright block they are easier to tune with the reed tips upwards, but flat mounted I makes little difference.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

penn

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 574
Re: Flat mount reed orientation
« Reply #3 on: February 09, 2016, 08:12:24 PM »

Excellent that's a consensus. The chap who fitted the reeds (probably Herr Koch or one of his colleagues) obviously did know what he was doing and I was right to follow his example and not my nose.

thanks
Steve
Logged
Hohners, Dino Baffetti, Lilly, Benny + a lot of junk.

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Flat mount reed orientation
« Reply #4 on: February 10, 2016, 07:19:00 AM »

My thinking would be that the reed tip is far from the hole to reduce turbulence, as this may alter the tone , it could also be to prevent the valve of the nonpaying reed from getting flipped back by the onrush of air, or it may have nothing to do with either of these things.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Flat mount reed orientation
« Reply #5 on: February 10, 2016, 07:24:21 AM »

Did you change the bass reeds? I would have expected to see brass reeds on the bass side since the treble reeds are brass. Also different type on nails and reed plates from one end to the other.
Are the pictures posted "before" or "after" photos? Some of the leathers are in need of attention.
« Last Edit: February 10, 2016, 07:27:38 AM by Psuggmog Volbenz »
Logged
I'm squeezin' and they're wheezin': old junker boxes

penn

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 574
Re: Flat mount reed orientation
« Reply #6 on: February 10, 2016, 08:16:43 AM »

Yes those are the "before" pictures - steel on individual plates on the bass, brass on unified plates on the treble.
I assume they're all original. The bass reeds have the Koch chamois stamp, which puts them at around the right date.
I posted some pictures of the case on a recent concertone thread [urli]http://forum.melodeon.net/index.php/topic,18102.msg222726.html#msg222726[/url]
as there seemed to be similarities in some of the parts, but that boxboard had quite different reeds.

Wrt turbulence - thanks Kimric, yes it sounds a sensible suggestion. Maybe I should turn them round and give it a try? Maybe not its taken me a couple of years to get it to a vaguely playable state.
Thanks,
Steve
Logged
Hohners, Dino Baffetti, Lilly, Benny + a lot of junk.

Inventor

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 117
Re: Flat mount reed orientation
« Reply #7 on: February 10, 2016, 03:56:23 PM »

On a concertina that I once designed; which was made in Moscow, with the reeds for each side all on one plate, Bayan style; one pair of reeds on the prototype was accidentally placed with the tips of the reeds immediately under the sound hole. The sounds produced by these reeds was absolutely awesome, and twice as loud as all the others.

Inventor 
Logged

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Flat mount reed orientation
« Reply #8 on: February 11, 2016, 02:44:58 PM »

Most reeds work best with the tip of the reed at the far end from the opening, whether mounted flat or on a conventional block.  The only exception is some high pitch reeds which respond better and produce more volume when reversed. On a typical treble reed bank you might find the highest two reed plates reversed. On an upright block they are easier to tune with the reed tips upwards, but flat mounted I makes little difference.

It's easy to see why with conventional reed blocks "tip up" is better than "tip down", just consider the airflow in through the pallet hole and out past the free end of the reed where most of it goes.

It's much more difficult to see why this should be best for flat-mounted reeds, you'd think the pallet hole would be better placed under the tip of the reed not the root.

Has anyone tried flat-mounted reeds both ways round in the same box? In the case with the pallet hole under the tip, you'd also think that a wedge to block out the chamber volume towards the root might be a good thing, this can't be done the other way round because maximum depth is needed under the tip. It's also possible that a small pallet hole won't work so well under the tip because of uneven airflow, so a bigger pallet hole is needed for "hole under tip".

In other words, just turning the reeds round and concluding that "pallet hole under tip" doesn't work might be because the reed chamber and pallet hole design aren't optimum for this case, rather than "pallet hole under root" being inherently better. Or not... ;-)

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Flat mount reed orientation
« Reply #9 on: February 11, 2016, 03:42:08 PM »

The reference back to the construction of concertinas and Iand D's suggestions remind me of something I read many years ago about concert hall 'tina players packing out any unused air space by gluing in bits of cork to achieve maximum volume (loudness).  Unfortunately no comment was made about what the tone was like!

Rob.
Logged

penn

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 574
Re: Flat mount reed orientation
« Reply #10 on: February 11, 2016, 07:07:35 PM »

The reed chambers in my Koch don't look "designed" as such - it's just a grid of scrap wood on which to lay the reeds. Or maybe that's another manufacturing advantage of rivets over holes?

I'm tempted to try turning them round - there are only ten plates in the bass end (I haven't started on the treble yet). However this has also been my first attempt at tuning (in short ....thanks to the melnet Haynes guide to melodeons, it went an awful lot better than I'd expected). There's still a little bit of tidying up to do, and I have a tendency to leave projects on the shelf for months on end.. so please don't hold your breath for results, it may have to wait til the next time I'm off sick from work.
Steve
Logged
Hohners, Dino Baffetti, Lilly, Benny + a lot of junk.

ChrisLDD

  • Good talker
  • **
  • Offline Offline
  • Posts: 64
  • ... but which way is up?
Re: Flat mount reed orientation
« Reply #11 on: February 15, 2016, 11:41:53 PM »

Most reeds work best with the tip of the reed at the far end from the opening, whether mounted flat or on a conventional block.  The only exception is some high pitch reeds which respond better and produce more volume when reversed. On a typical treble reed bank you might find the highest two reed plates reversed. On an upright block they are easier to tune with the reed tips upwards, but flat mounted I makes little difference.

It's easy to see why with conventional reed blocks "tip up" is better than "tip down", just consider the airflow in through the pallet hole and out past the free end of the reed where most of it goes.

It's much more difficult to see why this should be best for flat-mounted reeds, you'd think the pallet hole would be better placed under the tip of the reed not the root.

Has anyone tried flat-mounted reeds both ways round in the same box? In the case with the pallet hole under the tip, you'd also think that a wedge to block out the chamber volume towards the root might be a good thing, this can't be done the other way round because maximum depth is needed under the tip. It's also possible that a small pallet hole won't work so well under the tip because of uneven airflow, so a bigger pallet hole is needed for "hole under tip".

In other words, just turning the reeds round and concluding that "pallet hole under tip" doesn't work might be because the reed chamber and pallet hole design aren't optimum for this case, rather than "pallet hole under root" being inherently better. Or not... ;-)

Ian

I made a simple block of wood with a rectangular cut-out to accommodate and test flat-mounted reeds.
Using my new, electric fan driven, tuning table (sincere thanks to Scott Bellinger for his help with this) I tried various positions for the block, over air holes of various sizes.

My conclusion is that the reed invariably sounds best when the air enters at the rivet end.
The amplitude is greater, and the reed response is faster, i.e. reaches maximum amplitude in less time. (Ability to instantly change from suck to blow on the new tuning table made this very apparent.)

Note: if the air-hole is at the reed-tip end, with high air flow, the reed valve tends to get sucked down the holehttp://forum.melodeon.net/Smileys/default/grin.gif
Logged
Trying to learn enough magic to make my own melodeon.

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Flat mount reed orientation
« Reply #12 on: February 16, 2016, 05:15:11 AM »

Using my new, electric fan driven, tuning table

That sounds like a good idea - any chance of a few details?

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Flat mount reed orientation
« Reply #13 on: February 16, 2016, 07:09:51 AM »

As usual, I'm sure I'll be missing something pretty obvious, which everyone else can plainly see, but.............. all this talk of reed chambers and position of reed regarding the air hole and rivet, seem to be rather pointless! Surely the fact that only one of a pair of reeds can be favoured, either by the position of the actual reed/rivet  or the shape/size of the reed "chamber", then the whole discussion is meaningless? I mean, the other reed on the plate has the whole of the inside of the box as a "chamber" and the rivet will necessarily be at the opposite end!
Any help with my understanding would be greatly appreciated; I can ponder the situation as I sail up the Nile over the next few days. (The Chancellor won't let me take my instrument in case I frighten the tourists!)
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Flat mount reed orientation
« Reply #14 on: February 16, 2016, 09:52:36 AM »

Surely the fact that only one of a pair of reeds can be favoured, either by the position of the actual reed/rivet  or the shape/size of the reed "chamber", then the whole discussion is meaningless? I mean, the other reed on the plate has the whole of the inside of the box as a "chamber" and the rivet will necessarily be at the opposite end!

The two rivets can be at the same end of the reed plate.
And if the reeds are on a block so there's a 'chamber' inside the block, the chamber is acoustically coupled to the reed which ever way the wind is blowing.
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Flat mount reed orientation
« Reply #15 on: February 16, 2016, 04:26:51 PM »

... and the rivet will necessarily be at the opposite end!

Normal reed plates always have the rivets for both reed tongues at the same end. I've never ever seen a reed plate where the rivets are at opposite ends.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Flat mount reed orientation
« Reply #16 on: February 16, 2016, 04:35:01 PM »

... and the rivet will necessarily be at the opposite end!

Normal reed plates always have the rivets for both reed tongues at the same end. I've never ever seen a reed plate where the rivets are at opposite ends.

Neither have I.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Flat mount reed orientation
« Reply #17 on: February 16, 2016, 04:36:43 PM »

... and the rivet will necessarily be at the opposite end!

Normal reed plates always have the rivets for both reed tongues at the same end. I've never ever seen a reed plate where the rivets are at opposite ends.

Long plate reeds on Saxony boxes usually have a rivet at each end. I think that is what Edward has in mind
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

bellowpin

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 119
Re: Flat mount reed orientation
« Reply #18 on: February 19, 2016, 02:31:39 PM »

As usual, I'm sure I'll be missing something pretty obvious, which everyone else can plainly see, but.............. all this talk of reed chambers and position of reed regarding the air hole and rivet, seem to be rather pointless! Surely the fact that only one of a pair of reeds can be favoured, either by the position of the actual reed/rivet  or the shape/size of the reed "chamber",


  i wonder if anyone as tried to introduce some sort of partition in the reed chamber between the two reeds ??     it could foul the leather valve or the swinging reed tip if it extended too far  .. but should work alright near the rivet end . would it create a smaller acoustic volume which some have suggested is "better".  or would it create two distinct paths for the air flow with unforeseen effects .    just day dreaming  and curious!!       brian..
Logged
whole life in the shropshire hills. on the slow track and enjoying it.

ChrisLDD

  • Good talker
  • **
  • Offline Offline
  • Posts: 64
  • ... but which way is up?
Re: Flat mount reed orientation
« Reply #19 on: February 19, 2016, 03:10:43 PM »



  i wonder if anyone as tried to introduce some sort of partition in the reed chamber between the two reeds ??     it could foul the leather valve or the swinging reed tip if it extended too far  .. but should work alright near the rivet end . would it create a smaller acoustic volume which some have suggested is "better".  or would it create two distinct paths for the air flow with unforeseen effects .    just day dreaming  and curious!!       brian..
[/quote]

I too have been wondering about this. It would be tight, especially by the valve, but probablly worth trying.
Logged
Trying to learn enough magic to make my own melodeon.
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal