Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: tuning  (Read 5078 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
tuning
« on: February 10, 2016, 05:00:02 AM »

I have scoured this forum for all relevant information, but I have to admit I'm still a little uncertain about a few things when it comes to understanding tuning.  Maybe it's easier to explain what I DO understand:

With two sets of reeds, one is tuned slightly sharp or flat of the other which results in tremolo.  There are varying degrees of tremolo from very wet (a lot of vibrato) to completely dry (reeds sounding in unison).  Generally speaking, the amount of tremolo will be lower on the low notes and then progressively get higher as you go up the scale.  I can hear and understand this through "beats per second" (bps).  I don't understand Hz, or cents.  I actually have no understanding of them at all!

When it comes to various tunings (ie swing, demi-swing, etc) I understand they are often described as 1 bps, or 2 bps, etc. depending on the manufacturer's interpretation of what those terms mean to them.  What I don't understand is at what point along the scale one would listen and measure a particular number of beats per second.  For example, if a maker was to consider 2 bps to be "swing" tuning, where along the scale on a particular instrument would one play a note and hear 2 bps? The bps would be lower on one end and higher on the other.  I understand that people use A440 as a point of reference, but I don't actually understand what that means.  If I was to pick up an accordion and want to get a rough idea of the tuning (in the form of bps that could be communicated to a builder or tuner) how would I go about it?

Logged
C#/D player

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: tuning
« Reply #1 on: February 10, 2016, 07:54:03 AM »

It is worth searching for 'cents and hertz' on Google. There are quite a few places that explain what it means. Same goes for 'A=440', which is a reference pitch (so like when a violinist plays an A when an orchestra is tuning up). It is sometimes called concert pitch and it is not always 440.
I understand bps as a profile, or a graph, ranging from the lowest note(s) to the highest (on the instrument in question), with, say, the pitch along the x axis and bps on the y axis. So before I touch anything I always establish the existing 'profile' and work from that. Sometimes the bps (tremolo) tails off as the notes get higher, and sometimes it increases, and sometimes it remains constant. There is no right it wrong profile - it depends entirely on the choices that are made. The important thing is that it is consistent across rows and alters smoothly. So you don't want 3bps on the G on the G row and 6 bps on the G in the D row.

To answer your question about the tuning, try and count the 'beats' on the low notes, and sample the same up the keyboard. If you wanted you could actually draw a rudimentary graph, but you'd get a mental picture.  If it sounds like a box of angry bees it's probably wet tuned. (:)

All the above assumes two voices. it gets more complicated with more voices but the same principles apply.
« Last Edit: February 10, 2016, 08:02:11 AM by RogerThomas »
Logged

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: tuning
« Reply #2 on: February 11, 2016, 03:42:38 PM »

I don't understand Hz, or cents.  I actually have no understanding of them at all!

Tuning is a complex subject and I wouldn't attempt to answer all of your questions, indeed I don't have sufficient knowledge to do so, but every subject has a starting point and if you are familiar with the basic units involved in measuring pitch that's a good first step. Reeds create sound by swinging backwards and forwards through a slot in a reed plate, the sound you hear is caused by air passing through the very narrow slot between the reed and the plate, the reed itself makes no noise. When air is passed through a reed chamber the reed leaves its resting position and swings through the slot in the frame until the resistance of the spring steel overcomes the airflow and the reed swings back past its rest position and out of the other side of the frame until once again the spring steel resistance sends it back the other way. So if we call the rest position 0, the full reed swing in one direction +1 and the full reed swing in the other direction -1 then we have identified a swing cycle 0, +1, 0, -1, 0. One cycle is called one Hertz and it is used to measure fequency of pitch in Hz per second.

Cents are even easier to grasp as they are simply fractions of a half note or semitone. There are 12 semitones per octave in the tempered scale and a cent is one hundreth of a semitone, another tiny unit. This may not help you much in your quest for knowledge but you should be a bit less bamboozled by some of the jargon, hope this helps.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: tuning
« Reply #3 on: February 11, 2016, 04:24:09 PM »

I'm finding this thread to be fascinating, and this latest offering by Mr Dunk, especially helpful. Nevertheless, I'm intrigued by the mentioning of hearing (was that right, hearing?) the "beats". For the life of me, I cannot discern these at all!
Or possibly I can, if this is what you good people are referring to at 23 seconds into the following video from Samson James.
https://www.youtube.com/watch?v=s-nN_6U460Y
Mind you, I think it spoils the whole recording, as it runs on and off all the way through!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

tom f

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 112
Re: tuning
« Reply #4 on: February 11, 2016, 05:27:48 PM »

There is an US web site called 'accordion revival' with a lot of usefull information on it about accordions/melodeons in general and specifically regarding tuning and the relationship between bps, hertz and cents.  It's certainly worth a visit.
Logged

Stiamh

  • Old grey C#/D pest
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3611
    • Packie Manus Byrne
Re: tuning
« Reply #5 on: February 11, 2016, 05:41:08 PM »

When it comes to various tunings (ie swing, demi-swing, etc) I understand they are often described as 1 bps, or 2 bps, etc. depending on the manufacturer's interpretation of what those terms mean to them.  What I don't understand is at what point along the scale one would listen and measure a particular number of beats per second.  For example, if a maker was to consider 2 bps to be "swing" tuning, where along the scale on a particular instrument would one play a note and hear 2 bps? The bps would be lower on one end and higher on the other.  I understand that people use A440 as a point of reference, but I don't actually understand what that means. 

A440 means that the A above middle C (or the A in the first full octave of a box with a D row) is tuned to 440Hz / cycles per second, generally referred to as concert pitch. So it's just a reference point. If you buy an "A" tuning fork its tines will vibrate at 440 Hz and produce the note you would want to tune your fiddle's A string to, if you had one.

As to where along the scale... some tuning schemes are designed to produce the same tremolo at all points in the scale (sometimes referred to as Viennese tuning). But most tuners will, as you say, stick more or less to the same number of cents, which will result in increasing tremolo as you go up. So pick your point - say 2 bps at the A above middle C, or whatever you will. A tuner once described "tremolo Americano" to me as 9 cents at middle C, without specifying what would happen above that note.

For comparison, Bertrand Gaillard's tuner starts at the top and goes down. For what she calls "swing" she starts with 1 bps at the top of the scale, and reduces the bps value as she proceeds lower in pitch. In case this is of any use to you. :)

[Edited after checking correspondence to correct BG's tuner's description to "swing".]

Quote from: SS
Lorsque l'on me demande un accord swing, je pars des aigues et je mets 1 vibration par seconde, ensuite, je descend régulièrement vers les graves en enlevant du vibrato sur chaque note de façon régulière.
« Last Edit: February 11, 2016, 05:45:56 PM by Stiamh »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: tuning
« Reply #6 on: February 11, 2016, 06:07:52 PM »


As to where along the scale... some tuning schemes are designed to produce the same tremolo at all points in the scale (sometimes referred to as Viennese tuning). But most tuners will, as you say, stick more or less to the same number of cents, which will result in increasing tremolo as you go up.

I do something in between, unless my customer specifies differently. I start with, say, 2bps at A above middle C but gradually reduce the cents difference as I go up the range, but not so much as to keep a constant bps.  The result is a bps that increases as you go up in pitch, but avoids what can be an unpleasantly fast tremolo at the highest pitch. You might come across this being describes as tuning "on the curve" .   How much that change is I don't put into figures, I do what sounds good.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: tuning
« Reply #7 on: February 11, 2016, 06:25:25 PM »

When I dropped in to visit Jolly Roger, he showed me briefly a bokk which had graphs of the tuning typical of different manufacturers.  I wonder if you could let us know what that book is please, Roger?  It could spare a new entrant to tuning a lot of potentially expensive trial and error!

Rob.
Logged

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: tuning
« Reply #8 on: February 11, 2016, 06:30:18 PM »

How much that change is I don't put into figures, I do what sounds good.

AKA Black Magic!  ;D
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: tuning
« Reply #9 on: February 11, 2016, 06:31:32 PM »

For those with ;lesser experience or understanding..


please define "up the scale"   "down the scale"

In pitch or linearly such as on a piano ?

Also "starts at the top and goes down"   as in  starts at the top of the scale?    where.. low or high....   
Or on the keyboard... and what constitutes "top"... top meaning toward the floor or toward your chin?
 

Thanks.
« Last Edit: February 13, 2016, 04:25:46 PM by melodeon »
Logged

Stiamh

  • Old grey C#/D pest
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3611
    • Packie Manus Byrne
Re: tuning
« Reply #10 on: February 11, 2016, 06:48:36 PM »

Jeff - do you know anyone who would go up the scale to play a lower note?

Me neither.   :|glug

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: tuning
« Reply #11 on: February 11, 2016, 06:51:37 PM »

Up the scale means going from a low note to a high note, down the scale is from a high note to a low note. 'Start at the top' always refers to the highest pitch, knee end not chin end. It's confusing isn't it?
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: tuning
« Reply #12 on: February 11, 2016, 09:00:59 PM »

My students think it's funny when I point to the ceiling and say "down" then point to the floor and say "up".
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: tuning
« Reply #13 on: February 12, 2016, 11:20:35 AM »

This is the book Rob was referring to....
http://www.musicforaccordion.com/boutique/inform/bthierry/

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: tuning
« Reply #14 on: February 12, 2016, 03:58:09 PM »

Thaks Roger,

I'm sure some of us will have the requisite finances to get a copy - I'm still saving up.

Rob.
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: tuning
« Reply #15 on: February 13, 2016, 07:48:56 AM »

I do pretty much what Theo was describing, I roll off the tremolo offset a bit on the highest pitch notes to keep them from screaming, and add a bit to the lowest couple.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: tuning
« Reply #16 on: February 13, 2016, 12:22:11 PM »

When it comes to various tunings (ie swing, demi-swing, etc) I understand they are often described as 1 bps, or 2 bps, etc. depending on the manufacturer's interpretation of what those terms mean to them.  What I don't understand is at what point along the scale one would listen and measure a particular number of beats per second.  For example, if a maker was to consider 2 bps to be "swing" tuning, where along the scale on a particular instrument would one play a note and hear 2 bps? The bps would be lower on one end and higher on the other.  I understand that people use A440 as a point of reference, but I don't actually understand what that means. 

A440 means that the A above middle C (or the A in the first full octave of a box with a D row) is tuned to 440Hz / cycles per second, generally referred to as concert pitch. So it's just a reference point. If you buy an "A" tuning fork its tines will vibrate at 440 Hz and produce the note you would want to tune your fiddle's A string to, if you had one.

As to where along the scale... some tuning schemes are designed to produce the same tremolo at all points in the scale (sometimes referred to as Viennese tuning). But most tuners will, as you say, stick more or less to the same number of cents, which will result in increasing tremolo as you go up. So pick your point - say 2 bps at the A above middle C, or whatever you will. A tuner once described "tremolo Americano" to me as 9 cents at middle C, without specifying what would happen above that note.

For comparison, Bertrand Gaillard's tuner starts at the top and goes down. For what she calls "swing" she starts with 1 bps at the top of the scale, and reduces the bps value as she proceeds lower in pitch. In case this is of any use to you. :)

[Edited after checking correspondence to correct BG's tuner's description to "swing".]

Quote from: SS
Lorsque l'on me demande un accord swing, je pars des aigues et je mets 1 vibration par seconde, ensuite, je descend régulièrement vers les graves en enlevant du vibrato sur chaque note de façon régulière.

To be strictly correct, I believe Viennese tuning was reeds equal amounts above and below concert pitch but not with equal BPS over the whole keyboard -- as far as I know this was my idea (because I like the sound), which is why other people (not my idea!) refer to it as "Dedic" tuning...
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: tuning
« Reply #17 on: February 13, 2016, 04:25:00 PM »


"Jeff - do you know anyone who would go up the scale to play a lower note?"

Sadly,  yes.


And note that others concede... up the keyboard, down the keyboard is confusing to some.
Logged

Samson James

  • Member
  • *
  • Offline Offline
  • Posts: 7
  • Cats, dogs, hats, music and video games
    • Sam's Blog
Re: tuning
« Reply #18 on: July 10, 2022, 06:42:30 PM »

I'm finding this thread to be fascinating, and this latest offering by Mr Dunk, especially helpful. Nevertheless, I'm intrigued by the mentioning of hearing (was that right, hearing?) the "beats". For the life of me, I cannot discern these at all!
Or possibly I can, if this is what you good people are referring to at 23 seconds into the following video from Samson James.
https://www.youtube.com/watch?v=s-nN_6U460Y
Mind you, I think it spoils the whole recording, as it runs on and off all the way through!
Those ancient videos are so embarrassing! 😅
Logged
Mad dogs and englishmen

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: tuning
« Reply #19 on: July 10, 2022, 11:24:37 PM »

Nothing to be embarrassed about there, Bonny Lad!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal