Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Hohner Bellows re-tape  (Read 2088 times)

0 Members and 1 Guest are viewing this topic.

Mike Gott

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 285
  • Melodeon and hairy arm
Hohner Bellows re-tape
« on: February 12, 2016, 03:24:59 PM »

Have just completed my first (and hopefully only) full re-tape of a set of bellows, in this case on my Hohner Erica. I bought this new in 1990 and it is my Morris box - hence it had to cope with all sorts of mistreatment, spilt beer and inclement weather since that time. This winter I decided to give it a refresh.

I used approx 14 mtrs of CGM's 3/4" bellows tape with their own thick PVA type adhesive. After an abortive attempt to re-tape the end folds where they join the plastic end pieces I realised that the only way to do this properly was to take the ends off completely. This was done carefully and on a firm surface using an ordinary dinner knife (not sharp, round end) after marking bellows and ends to ensure that they were glued back in the same place.
 


I did one end, start to finish at a time and used the same glue as used for the tape. The bellows were clamped in a B&D Workmate to dry.



Advice that I would give in the light of the 10 hours that I've just spent on it are:

Take your time, have all your tools (sharp knife, cutting board, glueing board, glue applicator, steel rule) laid out beforehand.

Have your work area ready. I used the kitchen, having a water supply nearby is helpful, fingers and the glueing board are best washed very regularly to avoid it transferring to everything.

Have a weight available to put on the bellows while the glue sets - I used a cobbler's last.

Do maybe six pieces at a time - cut them, glue and fit them singly, then leave them to dry while you cut another six.

Do the top and bottom -the short sides - first, it will get you in practice for the slightly more fiddly long sides.

Put some strips of greaseproof paper in between the folds while the glue dries.

Have some relaxing music playing on the stereo!

It's worth the effort. I have also treated the Hohner to an Acorn keyboard (a lovely bit of kit) and some new mesh (sprayed gold) behind the grille to replace the beer stained and holed original.



Now I need someone to give me a Winter overhaul.

Many thanks to Theo for the grille mesh and the help and advice.

Mike


« Last Edit: February 12, 2016, 05:22:07 PM by Mike Gott »
Logged
"Traditional music was for entertainment, it wasn't for a further education class" (Bob Davenport)

Rivington Morris, Bolton, Lancashire.

911377brian

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1518
Re: Hohner Bellows re-tape
« Reply #1 on: February 12, 2016, 05:15:13 PM »

Nice job Mike. It would never have occurred to me to use the Workmate vertically; good tip...
Logged

tom f

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 112
Re: Hohner Bellows re-tape
« Reply #2 on: February 12, 2016, 05:50:22 PM »

Hi Mike,
That looks like an excellent job and far better than the one I'm doing at the moment.  It's taken me a long time to realise why, despite cutting the tapes to the correct size initially, they seem to end up as different lengths.  As I've been smoothing the tape onto the bellows the tape has been stretching.  Once I'd realised that, things feel into place much more easly.  I do need to do the bellows frame tapes but haven't been brave enough to separate the bellows from the frame yet.  Is this, and the regluing, fairly straight forward?
Logged

penn

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 574
Re: Hohner Bellows re-tape
« Reply #3 on: February 12, 2016, 07:14:59 PM »

I taped a 114 4 stop recently using Lester's video instructions and didn't remove the frame. It's possible to tease a gap between the last proper fold and the frame and push/cajole/stuff half the tape down the gap as per Lester's vid.
Steve
Logged
Hohners, Dino Baffetti, Lilly, Benny + a lot of junk.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner Bellows re-tape
« Reply #4 on: February 12, 2016, 07:24:18 PM »

Yes it is, and it helps if you trim the width of the last strip.  Take of 2 or 3mm along one edge.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Mike Gott

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 285
  • Melodeon and hairy arm
Re: Hohner Bellows re-tape
« Reply #5 on: February 12, 2016, 10:03:37 PM »

...Is this, and the regluing, fairly straight forward?

Yes, really. I was actually tying to tease the gap wide enough to push the tape down as Penn suggests when I realised that the table knife that I was using after liberating it from the draining board, had come clean out the other side! After that, the decision to take the whole thing off was easy! The knife actually went along very easily, separating the parts. I just had to work it a bit harder to do the corners but it wasn't difficult. Clean off any loose bits of paper after it's apart. Use the same bellows glue which gives you time to move it about a bit when you're re-assembling and clamp it up to set. I suppose the bottom line is, if I was doing it to another one, would I remove the ends again? The answer is definitely yes.

Mike
Logged
"Traditional music was for entertainment, it wasn't for a further education class" (Bob Davenport)

Rivington Morris, Bolton, Lancashire.

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Hohner Bellows re-tape
« Reply #6 on: February 13, 2016, 01:35:28 AM »

Nice job Mike. It would never have occurred to me to use the Workmate vertically; good tip...

Me neither. And it must be a better proposition than piling a dozen (?) sewing machines on top of the bellows as suggested IIRC on this forum some years ago    >:E   
Logged
Tuner/repairer, now retired.

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Hohner Bellows re-tape
« Reply #7 on: February 13, 2016, 07:58:23 AM »

It is possible to loosen the fold glued to the bellows frame, enough so that you can get the tape off but not so much as you have to remove the frame. It is less risky...there is a danger of damage to the bellows ends and it takes a lot longer to remove/reglue them on. Also you have to get the alignment exactly right and (of course) the frames the right way up etc. I decided removing the frames was only something you want to do if it is absolutely necessary.
Two boards (plywood, say) and some clamps work very well to hold the bellows together after gluing, if you don't have a workmate.

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Hohner Bellows re-tape
« Reply #8 on: February 13, 2016, 09:44:31 AM »

I must admit I usually do separate the bellows and frames, mainly because the final result (in my case anyway!) is neater. I haven't yet had any disasters, got the frames upside down/wrong way round or had any alignment/gluing problems. As I said....yet! I also use two plywood boards and a selection of heavy things during drying.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal