Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3 4 5 6 ... 9   Go Down

Author Topic: Project box  (Read 38947 times)

0 Members and 1 Guest are viewing this topic.

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Project box
« on: February 24, 2016, 10:56:31 PM »

So... After recently buying a G/C Pokerwork to learn to play on, I decided I'd like to learn more about the repair and maintenance side of things.  To this end, I bought an inexpensive project melodeon in clear need of repair on "that auction site".  Low and behold it arrived today...


Just what I had hoped!  Missing parts, mismatched hardware, rusty reeds, curled valves, leaky bellows (hurrah!)  And keyed in Bb/Eb as a bonus.

This thread is to document my progress, beg for advice, and ask many, many foolish questions.  ;D

I'll follow-up with specific questions in subsequent posts, but for starters: for those of you who do full restorations, do you have any general advice, things to avoid, things to remember?  Is there anything you wish you'd known when you were just starting out?  Any guidance gratefully accepted.


Logged

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #1 on: February 24, 2016, 11:38:24 PM »

Okay, specific question number 1:  What kind of wood is the case likely made of?  Spruce?  Birch? 

I've patterned a grill to replace the "plywood with a few holes" job.  Here's a shot of the current grill:


I found pictures on ebay of a one-row with similar decoration to get an idea of how the an original grill might have looked:


And mocked up a pattern for a new grill:


I may hand cut this on a scroll saw, or maybe have one laser-cut (depending on cost) - but what wood stock to use?


Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Project box
« Reply #2 on: February 25, 2016, 07:32:37 AM »

On seeing your photos and reading the description, my feeling would be to focus on the crucial part first - the reeds and valves. If you can't get them sounding and working reasonably well, there is little point in spending too much time on the other, more cosmetic, jobs.

You need to remove all the reeds from the reed blocks. I suspect in this instrument they will be pinned or nailed in position on a leather gasket rather than waxed. Gently ease the pins up to remove them and the reed plates should come free. You can then strip off and discard all the valves - all of them, don't try to salvage any - and then you will be able to see the state of both reed tongues on each plate.

If the reeds are severely rusted and pitted, they may be beyond use, but light to moderate surface rusting can be cleaned off using a scraper made from an old screwdriver blade or gently rubbing with fine carborundum. Fine grade carborundum (not sandpaper) manicure nail shaping boards cut into short narrow strips are good tools, as are glass-fibre pens used for cleaning electrical contacts prior to soldering. Support the underside of the reed tongue with a thin metal shim whilst working on it and always work from rivet to tip, to avoid damaging the delicate reed tip.

Overall, you want to aim for a clean set of reed plates and reed tongues. Get rid of all old glue and muck, and old wax if that's what was used. Then you need to replace all the valves. Get the proper sort from Charlie Marshall or similar supplier. Clean off dirt and muck from the reed blocks and replace the gasket if necessary, then you can replace the reeds and try sounding them. They will undoubtedly need retuning but that's something which can come later.

If your bellows don't leak too badly, you can use them to temporarily sound the reeds to see if it's worth proceeding, but leaks will need to be fixed, or if beyond repair, new bellows obtained.

Clearly there's a lot more to it than that, but this is how I would start the restoration, rather than worrying at this stage about what wood to make a new grille from. If you search through the forum you should find all the help and advice necessary to do the various jobs. Good luck!
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Project box
« Reply #3 on: February 25, 2016, 07:56:41 AM »

I think what you have there is a Hohner.  I can't make out a name anywhere, but I'm reasonably sure it is.  In that case you should find that a Hohner grill will fit.

The wood that the case is built from is probably birch, but for asking a new grill I'd suggest ply, with a veneer of your choice.  Veneering both sides helps to keep the material flat.  If you use solid timber there is a good chance of splits developing where the grain runs across narrow parts.

Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Project box
« Reply #4 on: February 25, 2016, 09:14:41 AM »

I think what you have there is a Hohner.  I can't make out a name anywhere ....
The Hohner name is visible on the first photo in the initial post.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Project box
« Reply #5 on: February 25, 2016, 09:26:40 AM »

Ah so it is.  I was viewing small versions on my phone and missed that.

So a Hohner grill would be an alternative to cutting a new one.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Project box
« Reply #6 on: February 25, 2016, 10:21:39 AM »

I`d buy a new pokerwork grille from Charlie Marshall for that :D
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Project box
« Reply #7 on: February 25, 2016, 10:37:37 AM »

Adam likes a bit of bling!  To me that would look completely wrong.  1930s box with a great patina and a modern high gloss stainless steel grill?  No thanks.  The idea makes my eyes hurt.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #8 on: February 25, 2016, 09:36:31 PM »

On seeing your photos and reading the description, my feeling would be to focus on the crucial part first - the reeds and valves. If you can't get them sounding and working reasonably well, there is little point in spending too much time on the other, more cosmetic, jobs.

Great advice.  The reeds are indeed screwed and pinned to the block with a gasket:



The picture above is representative of the overall condition of the reeds.  This is probably the worst of them:



From reading other threads, the consensus seems to be that wax alone is sufficient to secure the reeds - I do not need to replace the pins or screws.  Is this correct? 

Also, there is a leather strip used as a spacer between the block face and the reed plates that helps position the plates:



Does this need to be retained?

1930s box with a great patina and a modern high gloss stainless steel grill?  No thanks.

I'm with Theo on that one. 
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Project box
« Reply #9 on: February 25, 2016, 10:10:10 PM »

No need for wax with this design.  Stick with the leather gaskets and pins
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #10 on: February 25, 2016, 10:48:01 PM »

No need for wax with this design.  Stick with the leather gaskets and pins

Ah, excellent - thanks!  Is this material suitable?

http://www.cgmmusical.co.uk/CGM_Musical_Services/Felt_Leather_Pallets.html#15
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Project box
« Reply #11 on: February 25, 2016, 11:38:34 PM »

The old leather on the reed blocks looks fine.  If you do replace any (a fiddly job) you need something soft and of a similar thickness, a sheep leather is probably best.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Project box
« Reply #12 on: February 26, 2016, 01:10:05 AM »

No need for wax with this design.  Stick with the leather gaskets and pins

Ah, excellent - thanks!  Is this material suitable?

http://www.cgmmusical.co.uk/CGM_Musical_Services/Felt_Leather_Pallets.html#15

Yes, this is meant for reed block gaskets, where the reed plates are pinned or screwed in place. It's easy to work with - first of all cut it into narrow strips the same width as the partitions on the reed block using a sharp blade, a straight edge and a cutting board. Then progressively add pieces of the required lengths to the reed block, removing the backing paper bit by bit. It's a bit fiddly to do, but not too bad.

However...

This material is relatively thin, compared with the existing leather gaskets, so if you are going to use it, you need to completely remove and clean off the old leather first; if you try to combine the old and the new, you will most likely end up with air leaks.

As Theo mentions...

The old leather on the reed blocks looks fine.  If you do replace any (a fiddly job) you need something soft and of a similar thickness, a sheep leather is probably best.

... the old gasket looks to be in good condition, so don't remove it, unless you really have to.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Project box
« Reply #13 on: February 26, 2016, 01:16:26 AM »


Also, there is a leather strip used as a spacer between the block face and the reed plates that helps position the plates:



Does this need to be retained?

Yes - keep that in place. It forms part of the air seal at the rivet end of the reed plate. (Unless you are going to strip away all the old leather gasket, in which case you will need to replace it with some of the self-adhesive oloviecci material. See previous post about gaskets)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Project box
« Reply #14 on: February 26, 2016, 01:24:55 AM »

The picture above is representative of the overall condition of the reeds.  This is probably the worst of them:



That's not too bad - I've seen a lot worse! Clean the reed tongues as described earlier. The zinc oxide corrosion around the slot needs to be carefully scraped off to leave a clean flat surface so that the new valves will seat properly. Take care not to gouge out any grooves or undulations, or damage or enlarge the slot edge when scraping off the oxide.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #15 on: February 26, 2016, 04:18:22 AM »

Thanks, guys, for the help so far. 

As Theo mentions...

The old leather on the reed blocks looks fine.  If you do replace any (a fiddly job) you need something soft and of a similar thickness, a sheep leather is probably best.

... the old gasket looks to be in good condition, so don't remove it, unless you really have to.

Well, hmmmm.  To me it just looked like dried out old leather, so I'm afraid I already removed it.  :'( 
But that's okay - this is intended to be a learning experience, so I guess I'll learn how to build reed block gaskets.  The old gasket came off without much fight, leaving a slightly tacky residue.  A little light dressing with one of my wife's 4-way nail buffers (these are great, btw) and the mating surface of the block is smooth and clean.

That's not too bad - I've seen a lot worse!

It doesn't seem too stubborn.  With a five minute soak in some white vinager and a little work with a toothbrush and a wooden pick, most of it come off.  I have silicon-carbide papers on hand in 600 and finer grits, I'll see what I can accomplish tomorrow.

The zinc oxide corrosion around the slot needs to be carefully scraped off to leave a clean flat surface so that the new valves will seat properly.

Am I just going for shiny, or just smooth?
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Project box
« Reply #16 on: February 26, 2016, 08:11:53 AM »


That's not too bad - I've seen a lot worse!

It doesn't seem too stubborn.  With a five minute soak in some white vinager and a little work with a toothbrush and a wooden pick, most of it come off.  I have silicon-carbide papers on hand in 600 and finer grits, I'll see what I can accomplish tomorrow.

Be wary of over-cleaning the reeds. Remove any flaky rust and then polish with the fine carborundum if necessary. You may not be able to remove the residual darkish grey spots where the rust has been, but that's mostly OK. Removing too much material may have a significant effect on the tuning of the reed, so try to keep it to a minimum. Some people use an ultra-sonic bath/cleaner to remove the rust, which works very well, but you start getting into the realms of expensive equipment.

I'd be a bit wary of the vinegar, except perhaps for a very short time. My concern would be for the rivet end - you don't want to disturb the integrity of the join. Make sure you rinse all the vinegar away thoroughly. The trouble with cleaning off rust this way is that you leave the steel surface prone to rusting again. New reeds often have an anti-rust bluing coating.

There have been discussions on this forum in the past about the desirability, or not, of using a product like WD40 to dispel any residual moisture from reed tongues. Normally, anything like WD40 or oil/grease of any sort should never, ever be used on any component of a melodeon -  not ever, ever at all, basically because it attracts dust and muck and can eventually cause seizing of the mechanisms. However, the consensus of the discussion (as I recall) was that a very fine film of WD40 applied extremely sparingly (say with a cotton bud, or similar) to the reed tongue and then wiped clean was probably beneficial and not harmful. Theo might well have some comments about this!

The zinc oxide corrosion around the slot needs to be carefully scraped off to leave a clean flat surface so that the new valves will seat properly.

Quote
Am I just going for shiny, or just smooth?

Just smooth should be fine. An old stiff toothbrush will probably do most of the job. You will eventually be gluing a valve at the rivet end, so the last 1/4" or so needs to be especially free of loose dust. I also run a cotton bud moistened with acetone or methylated spirit over the gluing surface prior to gluing the valve on. 
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

JimmyM

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 103
Re: Project box
« Reply #17 on: February 26, 2016, 08:42:37 AM »

This is one of my favourite threads on melnet and likely to cause a new varient of MAD  (:)
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Project box
« Reply #18 on: February 26, 2016, 08:47:18 AM »

As Theo mentions...
The old leather on the reed blocks looks fine.  If you do replace any (a fiddly job) you need something soft and of a similar thickness, a sheep leather is probably best.

... the old gasket looks to be in good condition, so don't remove it, unless you really have to.

Well, hmmmm.  To me it just looked like dried out old leather, so I'm afraid I already removed it.  :'( 
But that's okay - this is intended to be a learning experience, so I guess I'll learn how to build reed block gaskets.  The old gasket came off without much fight, leaving a slightly tacky residue.  A little light dressing with one of my wife's 4-way nail buffers (these are great, btw) and the mating surface of the block is smooth and clean.


OK - you now have a choice. Either:
(a) replace the old gasket with new oloviecci from Charlie Marshall, then secure the reed plates with screws/nails as before.
(b) dispense with the gasket method altogether and wax the reed plates into place.

At this stage, I'd probably choose the waxing method, because it is quick and effective. But I realise that it could seem a bit daunting to someone who has never done it before. But you did say this is a learning experience for you, so if you do choose to use the waxing method, there are, once again, plenty of past threads on this forum to help you; also Youtube videos.

You will also need the right stuff - a wax block or sticks from Charlie Marshall are ideal. Also a proper way of heating and applying the wax - basically a choice between a wax melting pot and 'spoon', for use with block wax, or a temperature controlled soldering iron for use with wax sticks.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Project box
« Reply #19 on: February 26, 2016, 08:56:45 AM »

You will also need the right stuff - a wax block or sticks from Charlie Marshall are ideal. Also a proper way of heating and applying the wax - basically a choice between a wax melting pot and 'spoon', for use with block wax, or a temperature controlled soldering iron for use with wax sticks.

And wear a facemask, I tell you this as a born again asthmatic since doing too much waxing with out one!
Pages: [1] 2 3 4 5 6 ... 9   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal