Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2] 3 4 5 6 7 ... 9   Go Down

Author Topic: Project box  (Read 38805 times)

0 Members and 1 Guest are viewing this topic.

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #20 on: February 26, 2016, 05:30:45 PM »

This is one of my favourite threads on melnet and likely to cause a new varient of MAD  (:)

Haha - BOMAD: Broken Old Melodeon Acquisition Disorder.  eBay is gonna love it!

OK - you now have a choice. Either:
(a) replace the old gasket with new oloviecci from Charlie Marshall, then secure the reed plates with screws/nails as before.
(b) dispense with the gasket method altogether and wax the reed plates into place.

I will have to ponder this.  My inclination is to stay with screws and gaskets, as I have not yet disturbed the gasket on the other blocks.  Also, the benefit of being able to more easily remove and replace individual reeds seems like it may be useful in case rework is needed.

In either case, the cleaning of reeds continues.  How does this look?  Too much?  Too little?  This is just with an ultra-fine grit silicon-carbide fingernail buffer. 

BEFORE

AFTER
As you see, there is some pitting and discoloration, but it feels smooth to the fingertip.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Project box
« Reply #21 on: February 26, 2016, 06:02:35 PM »

I view waxing instead of screws/pins on leather as a downgrade. So sticking with the gaskets is good.

The cleaning looks fine.  The critical areas are the edges of the reed tongue and the edges of the slot in the reed plate.  A useful check is too place a bright surface behind the reed plate and look for an even gap all round the reed tongue. It is best seen with the reed tongue held Dow flush with the top of the reed plate.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #22 on: February 26, 2016, 09:13:23 PM »

Like this?

Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Project box
« Reply #23 on: February 26, 2016, 11:58:26 PM »

Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Grape Ape

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1209
Re: Project box
« Reply #24 on: February 27, 2016, 04:04:49 AM »

Wow! This is an interesting thread.  And one that could get me into even more trouble than I am already in.
Logged

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #25 on: February 28, 2016, 03:08:16 AM »

Wow! This is an interesting thread.  And one that could get me into even more trouble than I am already in.

It seems we're on a parallel path - you may as well start looking for a fixer-upper.  Resistance is futile.
Logged

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #26 on: February 29, 2016, 04:40:54 PM »

Just a quick update for those following along at home - I've started an order with CGM for valves, olovisc, pallet leather, bellows tape and gasket, and other miscellany, and will proceed with cleaning valves in the interim.

Stay tuned...
Logged

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #27 on: February 29, 2016, 04:52:50 PM »

I will say that while cleaning by hand is going fairly quickly, it is awfully tempting to put them in a small ultra-sonic cleaner with some suitable solvent as has been mentioned in another thread - not so much to save the handwork, but to get a more thorough cleaning. I have a small cleaner that I use for other projects.

I understand this will remove the bluing and leave the reeds more susceptible to new rust, though I am curious if this has been seen in practice.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Project box
« Reply #28 on: February 29, 2016, 04:55:54 PM »

I've used an ultrasonic bath.  You still have to hand clean the reeds to get red of glue, wax, and anything but the thinnest layer of corrosion.  It is true that it takes the blue coating off the reed. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #29 on: February 29, 2016, 07:42:53 PM »

It is true that it takes the blue coating off the reed.

Thanks, Theo.  Have you seen any evidence that removing the coating hurts anything?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Project box
« Reply #30 on: February 29, 2016, 07:46:07 PM »

No. The blue is from the tempering process when the steel is heat treated. There is no blue on the top anyway, it's removed when the reed profile is ground and filed.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #31 on: March 01, 2016, 09:11:31 PM »

Just to keep it going... Here's a couple of pics. 

Removed and cleaned up the treble side pallets by scraping off the old leather facing material and sanding the bottoms of the pallets with 220 grit sandpaper on a smooth sheet of glass:


And here's my organization for reeds, now cleaned and awaiting valves:



It's probably a little excessive, but I wanted to keep track of exactly what came from where, not knowing the current state of tuning - which leads me to a question...

I understand that the usual convention for tuning is to tune one reed ("M") to pitch (say, 440hz) and the second reed ("M+") sharper by whatever the desired offset is (say, +15 cents, about 443.8hz).  Is there any convention around which reed is "M" and which is "M+"?

As always,  thanks for your patience and guidance so far.





Logged

mr hohner

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 189
  • K.BLAND Melodeons
Re: Project box
« Reply #32 on: March 01, 2016, 09:26:25 PM »

Just to keep it going... Here's a couple of pics. 

Removed and cleaned up the treble side pallets by scraping off the old leather facing material and sanding the bottoms of the pallets with 220 grit sandpaper on a smooth sheet of glass:


And here's my organization for reeds, now cleaned and awaiting valves:



It's probably a little excessive, but I wanted to keep track of exactly what came from where, not knowing the current state of tuning - which leads me to a question...

I understand that the usual convention for tuning is to tune one reed ("M") to pitch (say, 440hz) and the second reed ("M+") sharper by whatever the desired offset is (say, +15 cents, about 443.8hz).  Is there any convention around which reed is "M" and which is "M+"?

As always,  thanks for your patience and guidance so far.

Keeping thing organised is the right thing to do, you can never be over organised... In the past I've fixed boxes and then forgotten what goes where when it comes to putting it back together again... You're doing a great job, well done!!!
 (:)
Logged
Castagnari Studio D/G, Serenelli D/G, Hohner Pokerwork D/G, Castagnari Lilly D/G , Sandpiper Dublin II G/C, Serenelli Silyvia G/Acc

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Project box
« Reply #33 on: March 01, 2016, 09:32:35 PM »

I understand that the usual convention for tuning is to tune one reed ("M") to pitch (say, 440hz) and the second reed ("M+") sharper by whatever the desired offset is (say, +15 cents, about 443.8hz).  Is there any convention around which reed is "M" and which is "M+"?

Just about every block I have tuned has been arranged like this - with the block sideways on in front of you with the low notes on the left and high on the right the reed plates facing you are tuned to pitch and the reed plates on the far side of the block are tuned sharp.

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #34 on: March 01, 2016, 10:03:02 PM »

Keeping thing organised is the right thing to do, you can never be over organised... In the past I've fixed boxes and then forgotten what goes where when it comes to putting it back together again... You're doing a great job, well done!!!
 (:)

Thank you!  I should probably not mention the other reason, which is I have to be able to shove everything back into the it's hiding place as soon as I hear my wife coming so she won't find out about my new mistress!  :Ph Just kidding (sort of).

Just about every block I have tuned has been arranged like this - with the block sideways on in front of you with the low notes on the left and high on the right the reed plates facing you are tuned to pitch and the reed plates on the far side of the block are tuned sharp.

Perfect answer - thanks, Lester!
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Project box
« Reply #35 on: March 01, 2016, 11:20:32 PM »

But unless you have coupler slides under some blocks it is not terribly important.  I sometimes find it helpful to place a strip of masking tape along the top surface of the block, then I can make notes about what goes where and not leave the wood messed up with graffiti.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #36 on: March 02, 2016, 08:20:29 PM »

I sometimes find it helpful to place a strip of masking tape along the top surface of the block, then I can make notes about what goes where and not leave the wood messed up with graffiti.

That's a great idea.  Even though it's on the inside, there's something I find distasteful about marking up clean 80 year old wood.
Logged

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #37 on: March 02, 2016, 09:32:59 PM »

While I am waiting on supplies today, I tackled a small but satisfying job.  At some point in the box's history, it appears the treble mechanism was serviced and remounted with flat head screws of various lengths, driven in from the back and protruding through the mounting holes in the mechanism:



To correct this, I replaced the lower reed block stop with a larger block of western red cedar which could act both as a stop for the reed block, and as a backing to hold the proper round head #4 wood screws, driven in from the front:



First, I removed the old stop block:



After scraping of the glue and sanding smooth, reinstall the reed block and check for alignment:


Then mark and drill pilot holes in the new stop block, reinstalling with just a smear of wood glue:


Oops - the screws are just a titch too long:



Nothing a washer can't solve:



Snug and flush:

Logged

mr hohner

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 189
  • K.BLAND Melodeons
Re: Project box
« Reply #38 on: March 02, 2016, 09:51:45 PM »

While I am waiting on supplies today, I tackled a small but satisfying job.  At some point in the box's history, it appears the treble mechanism was serviced and remounted with flat head screws of various lengths, driven in from the back and protruding through the mounting holes in the mechanism:



To correct this, I replaced the lower reed block stop with a larger block of western red cedar which could act both as a stop for the reed block, and as a backing to hold the proper round head #4 wood screws, driven in from the front:




First, I removed the old stop block:



After scraping of the glue and sanding smooth, reinstall the reed block and check for alignment:


Then mark and drill pilot holes in the new stop block, reinstalling with just a smear of wood glue:


Oops - the screws are just a titch too long:



Nothing a washer can't solve:



Snug and flush:



You're doing a fab job!!! Everything looks neat and tidy (looks like Theo's got a competitor..)
 ;D
Logged
Castagnari Studio D/G, Serenelli D/G, Hohner Pokerwork D/G, Castagnari Lilly D/G , Sandpiper Dublin II G/C, Serenelli Silyvia G/Acc

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #39 on: March 02, 2016, 10:26:19 PM »

I very much doubt I'll ever be any competition to Theo, but it is nice to have giants with shoulders to stand upon. 
Logged
Pages: 1 [2] 3 4 5 6 7 ... 9   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal