Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 3 4 [5] 6 7 8 9   Go Down

Author Topic: Project box  (Read 38847 times)

0 Members and 1 Guest are viewing this topic.

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Project box
« Reply #80 on: March 30, 2016, 09:53:15 PM »

Quote
Next up, valves.  I understand that Bostik solvent free clear contact adhesive is preferred by many of you, but it is unavailable in the US.  Any suggestions on an equivalent contact adhesive available in the States?

I don't know how it compares to the Bostik product, but I've had good success with Gorilla Super Glue which I tried based on a recommendation from someone here (forrest I think).
Logged

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #81 on: March 31, 2016, 10:25:15 PM »

I starting to look at doing the treble side valves today.  The valves I obtained are a mix of, from longest to shortest, synthetic leather (Vileda), three layer black film, two layer black film, and small two layer white plastic.  Are there any standards or rules of thumb on which valve types to use on what reeds?

Using the nearest voiced reed (pitch and octave) from my G/C Pokerwork as a guide, here is my guess:



Does this look like a sensible layout?

I don't know how it compares to the Bostik product, but I've had good success with Gorilla Super Glue which I tried based on a recommendation from someone here (forrest I think).

I would not have considered a cyanoacrylate glue.  Do you a few seconds to re-position the valves or does it stick fast upon contact?  I can imagine myself with valves stuck to each and every finger :)

Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Project box
« Reply #82 on: March 31, 2016, 11:04:11 PM »

I would not consider cyanoacrylate for fixing valves either.
As far as which valves to use, my general rule of thumb is to use the smallest size that will cover the vent.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Project box
« Reply #83 on: April 01, 2016, 02:43:23 AM »

Quote
I would not have considered a cyanoacrylate glue.  Do you a few seconds to re-position the valves or does it stick fast upon contact?  I can imagine myself with valves stuck to each and every finger :)

I know what you mean.  Gorilla Super Glue is a slowish cyanoacrylate, not the instant type, so there is plenty of time to position the valve.  Works much the same as contact cement, except it is less stringy.   Works fine with plastic and leather valves too.  I'm sure there are other fine glues, this one has just worked well for me...         
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Project box
« Reply #84 on: April 01, 2016, 07:58:50 AM »

...
As far as which valves to use, my general rule of thumb is to use the smallest size that will cover the vent.

What Theo said.

It's especially important for the valves on the underneath of the reed plate. If they are too long, there is an increased risk that the valves will foul the end of the reed chamber, so you will need to measure each length carefully and probably trim the valves to length. 0.5 mm overlap over the end of the slot is all you need.

Also, ensure that the long edge of the valve will not contact the wall of the reed chamber. I tend to fix the underneath valves very slightly off-centre, biased towards the centre of the reed plate, in order to prevent possible contact with the reed chamber wall. It tends to be the larger and medium sized reeds/valves which may need this precaution. It's also worth checking that the reed chamber walls are smooth with no projecting splintery bits which could catch the valves.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Project box
« Reply #85 on: April 01, 2016, 08:09:38 AM »

Quote
Next up, valves.  I understand that Bostik solvent free clear contact adhesive is preferred by many of you, but it is unavailable in the US.  Any suggestions on an equivalent contact adhesive available in the States?

I don't know how it compares to the Bostik product, but I've had good success with Gorilla Super Glue which I tried based on a recommendation from someone here (forrest I think).

If you can get Bison Kit, that's pretty much the same as Bostik - at least for our purposes.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #86 on: April 01, 2016, 07:38:44 PM »

...
As far as which valves to use, my general rule of thumb is to use the smallest size that will cover the vent.

What Theo said.

Okay - this will simplify things as I will have no need for the three layer or Vileda valves on the treble side.

Also, thanks for the caveat about interference with the underside valves.  There appears to be a reasonable amount of clearance, but I will trim place and carefully.  Do you pre-trim the valves or trim them after gluing?

If you can get Bison Kit, that's pretty much the same as Bostik - at least for our purposes.

Yes, I'd seen this in your comments on other threads and looked for it.  It's available for US delivery through a boutique seller on Amazon, but long delivery times :(  I think I will go ahead with the E6000.  If it works well, it'll be another documented option at least.

Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Project box
« Reply #87 on: April 01, 2016, 08:34:44 PM »

Do you pre-trim the valves or trim them after gluing?

I fit them then trim them, to me seems easier.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Project box
« Reply #88 on: April 01, 2016, 08:43:02 PM »

Yes trim after gluing in place, otherwise it's difficult to get the length right.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #89 on: April 01, 2016, 10:56:39 PM »

So, here's my first attempt at gluing valves.  ::)

First, I give the gluing surface on the reed plate a little swipe with denatured alcohol as a final prep.


Then working on a stack of post-it notes, I dab a small blob of adhesive to the very top of the back side of the valve.  I smear the blob over about the 3mm or so with the back of a popsicle stick (lolly stick).  I can't remember who mentioned using a post-it pad as a work surface, but it works great - when too much excess accumulates, just peel off the top note and throw it out.


Next I position the valve, butting it against the rivet, and press firmly with a fingertip while the contact adhesive grabs hold.  The E6000 seems to need a good, slow 10 count. 


To trim, I slide an index card under the valve and the adjacent reed, using the reed tip as a reference for the length of the slot under the valve, and the index card's line to help me judge where to trim.  I was shooting for .5mm of overlap, as Steve recommended.  I trim with an exacto knife - no problem getting a clean cut.  The index card helps protect the reed plate from scoring.


And here's the result:



Probably could be neater, but hopefully acceptable in function.  So far, none of the valves have fallen off, which I guess is a good sign.
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Project box
« Reply #90 on: April 02, 2016, 01:00:32 AM »

So, here's my first attempt at gluing valves.  ::)
.
.
.
Probably could be neater, but hopefully acceptable in function.  So far, none of the valves have fallen off, which I guess is a good sign.
Looking really good!

Do you pre-trim the valves or trim them after gluing?
I fit them then trim them, to me seems easier.

Yes trim after gluing in place, otherwise it's difficult to get the length right.

Bucking the trend here - I trim the valves to length first, then glue into place.
I offer the valve up to the rivet head and at the other end I make a small mark with a soft pencil where the valve should be trimmed. Then I use a pair of sharp scissors to trim the valve to length. Quick and easy!
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Project box
« Reply #91 on: April 02, 2016, 08:51:51 AM »

Mmmm. Looks really neat but in my world I always trim the second part of the valve by a similar proportion to the amount I trim off the main part. Otherwise the valves where the main  part is trimmed short become stiffer.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Project box
« Reply #92 on: April 02, 2016, 09:03:04 AM »

Mmmm. Looks really neat but in my world I always trim the second part of the valve by a similar proportion to the amount I trim off the main part. Otherwise the valves where the main  part is trimmed short become stiffer.

Yes - good point Lester. I often do that too, depending on how much of the original length I have removed. If it's only a millimetre or so then I don't bother with trimming the booster leaves, but with any more shortening then I trim the boosters too by a relative amount.

The other factor which can affect the stiffness of the valve is the length of the glued section. I've not really analysed this too much, just gone with my gut feeling and experience, but I guess as a rule of thumb for the medium and small valves, I make the glued length fractionally longer than the valve is wide. For the larger valves, especially for the big bass reeds, I make my glued length longer - perhaps twice the valve width?

Any other viewpoints on this?
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Project box
« Reply #93 on: April 02, 2016, 09:34:33 AM »

The other factor which can affect the stiffness of the valve is the length of the glued section. I've not really analysed this too much, just gone with my gut feeling and experience, but I guess as a rule of thumb for the medium and small valves, I make the glued length fractionally longer than the valve is wide. For the larger valves, especially for the big bass reeds, I make my glued length longer - perhaps twice the valve width?

Sounds about what I do.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Project box
« Reply #94 on: April 02, 2016, 09:46:14 AM »

As to applying the glue, I have my tube of glue held in my desk vice



A small amount of finger pressure gets a blob of glue on the nozzle tip and I wipe the valve over it.
« Last Edit: April 02, 2016, 10:23:02 AM by Lester »
Logged

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Project box
« Reply #95 on: April 02, 2016, 10:52:41 AM »

Useful for getting the last drop of glue out the tube. A similar model is available for toothpaste.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

911377brian

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1518
Re: Project box
« Reply #96 on: April 02, 2016, 11:08:37 AM »

That is ingenious Lester...
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Project box
« Reply #97 on: April 02, 2016, 12:07:27 PM »

Not my idea, stolen off Pete Grasby

mr hohner

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 189
  • K.BLAND Melodeons
Re: Project box
« Reply #98 on: April 21, 2016, 01:06:43 PM »

Any updates on progress or has it been postponed for a while?
 :||:
Logged
Castagnari Studio D/G, Serenelli D/G, Hohner Pokerwork D/G, Castagnari Lilly D/G , Sandpiper Dublin II G/C, Serenelli Silyvia G/Acc

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #99 on: April 26, 2016, 04:01:20 PM »

Any updates on progress or has it been postponed for a while?
 :||:

Sorry for the lack of updates, guys.  Life happens sometimes, and has been happening to me quite a lot in the last few weeks :)  Here is a synopsis of my progress:

1. Taking the consensus on using the shortest valve that is long enough, I ran myself out of the 2 layer valves and had to order some more.  Received these about a week ago.

2. I finally was able to complete the treble side yesterday, reinstall the reed blocks, and run through the notes.  I ended up with one plate installed wrong-side-down, but since these are screwed and pinned in (rather than waxed) it was simple to correct this.  Hooray screws and pins :) 

All things considered, I am pretty pleased with the sound of the treble side.  Of course, the tuning is off, but not as bad as you might expect.  No horrible sounds or any that fail to sound.  The reeds actually sound pretty nice to my inexperienced ear - sweet and mellow in comparison to my 60's Pokerwork.  It makes me wish I knew how to play the thing :|bl

I will record a sound file and solicit informed opinions before I get started on the bass side.

Mmmm. Looks really neat but in my world I always trim the second part of the valve by a similar proportion to the amount I trim off the main part. Otherwise the valves where the main  part is trimmed short become stiffer.

That makes perfectly good sense to me, though I'm sure I would never have thought of it.  What is the effect of a "too stiff valve"?  The higher notes do seem to need a bit more oomph to get them going.
Logged
Pages: 1 2 3 4 [5] 6 7 8 9   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal