Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 3 4 5 6 [7] 8 9   Go Down

Author Topic: Project box  (Read 38985 times)

0 Members and 1 Guest are viewing this topic.

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #120 on: May 04, 2016, 07:31:45 PM »

Regarding the effect of tuning in situ vs. on the table, will the difference generally be consistent for pairs of reeds?  That is, will the compensation for a given "M" reed be about the same as for the corresponding "M+" reed?  I'm wondering whether I should:

A. Calculate and apply the in-situ/on-table difference for each read; or
B. Apply compensation only to the M reed and tune the M+ reed relative to the tuned M reed.

I'm really trying to minimize the amount of final tuning, to keep from having to remove and replace bellows more than needed.

Also, I've created a google sheet with my findings so far.  As I measure it, I'm figuring on compensation anywhere from +.4 cents to -5.5 cents with most needing to be flattened (i.e., pitches are sharper when reeds are installed.)

Does match your experience?  Just looking for a sanity check before I start scratching up reeds  :o
« Last Edit: May 04, 2016, 07:33:30 PM by Jef »
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Project box
« Reply #121 on: May 04, 2016, 07:42:40 PM »

I may get my knuckles rapped but here goes.

For example Push C4 calls for a -4.8c correction but that is to move the frequency by 1.3Hz in 261Hz - .4%. Now I know I'm old but I'm not sure anyone could detect that difference by ear.

You need to concentrate on getting as close as possible but fiddling with sub cent tuning is a waste of time.

The ear and therefore the final result will be far more dependant in the difference between to two reeds that sound for each note, the beat frequency. This is where fine tuning will be needed but, as Theo said here or somewhere else on melnet, this is best done by ear.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Project box
« Reply #122 on: May 04, 2016, 08:08:45 PM »

Regarding the effect of tuning in situ vs. on the table, will the difference generally be consistent for pairs of reeds?  That is, will the compensation for a given "M" reed be about the same as for the corresponding "M+" reed?
It will be similar, but not necessarily consistent. This is because the M reeds and the M+ reeds occupy different spatial locations inside the instrument. Factors such as proximity of the reeds to the internal walls of the instrument and the bellows folds can affect the final pitch. Similarly, the position on the reed block seems to have an effect on the difference in pitch outside of, and inside the instrument: reeds on the ends of the reed block seem to behave differently compared with those in the main body of the block. It might well be something to do with the relative rigidity of the reedblock (a) at the ends which are clamped and (b) away from the ends. This is where a reed block connecting brace strip screwed across the top of the blocks helps.

Quote
I'm wondering whether I should:
A. Calculate and apply the in-situ/on-table difference for each read; or
B. Apply compensation only to the M reed and tune the M+ reed relative to the tuned M reed.

This is my methodology in this situation. Others may do it differently  ;)

1. Reeds in situ in the instrument: Block off all the M+ reeds with a strip of paper underneath the reed block openings.
2. Sound all the M reeds in sequence and note down the deviations from E.T. (I assume)
3. Repeat for the M+ reeds.
Next...
4. Reedblocks outside the instrument on your tuning bellows: Sound the M reeds and note again the deviation from E.T.
5. Using your tuning tools, files, scratchers, etc. tune each reed up or down by the difference from E.T. noted in step 2. For example: if, in step 2 your A4 reed was 2.5 cents flat from E.T, and in step 4 it was 1 cent sharp of E.T., you need to raise the pitch of A4 on the tuning table to +3.5 cents (i.e. 1 cent measured in step 4 plus the 2.5 cents absolute correction needed from step 2, = 3.5 cents).

These steps should get the M reeds close to where they need to be. Put the reed block back in the instrument and test the M reeds again (steps 1 and 2). Repeat steps 4 and 5 again if necessary.

Now for the M+ reeds... If you have calculated what the theoretical offset should be to give you the desired tremolo, and having established the M+ 'as received' values in step 3, you can repeat steps 4 and 5 for the M+ reeds, which should also get you somewhere very close to where they need to be.

6. Put all the reeds back in situ and listen carefully to each note, and make a decision whether the tremolo is too much, too little or, as sometimes happens, none at all, if the tuning is too close between M and M+.
7. Assuming the M reeds are now OK from the previous steps, to increase the tremolo you need to sharpen the M+ slightly, to decrease the tremolo you need to flatten it slightly. At this stage don't try to calculate anything; use your ears and do slight reiterative adjustments until you've got it sounding 'right' to your ears.

Next stage (echoing Dave Elliott, concertina repairer and tuner), go and have a pint (or two); you will have earned it.


Edit: Lester has said much the same thing while I was composing my lengthy response, but as usual, his reply is far more succinct and just as much to the point!   ;)
« Last Edit: May 04, 2016, 08:11:25 PM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Project box
« Reply #123 on: May 04, 2016, 08:27:59 PM »

Isn't this site just great? I'm drinking in all this info for when I get to make a start on my 3-stop project. (If and when I pluck up the courage!)
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Project box
« Reply #124 on: May 04, 2016, 08:30:00 PM »

I may get my knuckles rapped but here goes.

For example Push C4 calls for a -4.8c correction but that is to move the frequency by 1.3Hz in 261Hz - .4%. Now I know I'm old but I'm not sure anyone could detect that difference by ear.
I'm never in the business of rapping anyone's knuckles, but I will respectfully and gently disagree with Lester's example on a couple of points:

1. I think a 4.8 cent 'error' at pitch C4 should be audible to most (or at least many) people. If you had two C4 reeds, one at pitch and one 4.8 cents adrift, it should be possible to distinguish the two pitches when they are sounded one after another.

2. Unless you are into wet tuning, a 4.8 cent error can make an audible difference to the tremolo rate at C4 pitch, especially if you are in the business of light-swing Castagnari-type tuning. My own methodology is to get the M reeds as close as possible to 'proper pitch' (be it ET or any other standard) which then gives me a firm pitch foundation upon which to lay the bricks of tremolo in order to give you a well-built wall of sound which is characteristic of the melodeon.  :P

Getting my coat now...

Where is the lovely Samantha when you need her...?
« Last Edit: May 04, 2016, 08:39:27 PM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Project box
« Reply #125 on: May 04, 2016, 11:51:18 PM »

That seems like a lot of faffing about.  Why not just learn to tune the reeds in the box?  You can use the instruments own bellows, just need to make a simple hangar to attach it to the side of your workbench.  I use a very simple setup with two strips of wood clamped to my bench and projecting over the side,  the bellows folds slide into these two rails.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #126 on: May 05, 2016, 03:55:16 AM »

That seems like a lot of faffing about.  Why not just learn to tune the reeds in the box?  You can use the instruments own bellows, just need to make a simple hangar to attach it to the side of your workbench.  I use a very simple setup with two strips of wood clamped to my bench and projecting over the side,  the bellows folds slide into these two rails.

A fair point.  It seems like it would be a lot easier to scratch and file the reeds without having to deal with the clearance issues of having the blocks installed, and it being my first time, I correlate "ease" with "likelihood of success."
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Project box
« Reply #127 on: May 05, 2016, 07:52:04 AM »

That seems like a lot of faffing about.  Why not just learn to tune the reeds in the box?  You can use the instruments own bellows, just need to make a simple hangar to attach it to the side of your workbench.  I use a very simple setup with two strips of wood clamped to my bench and projecting over the side,  the bellows folds slide into these two rails.

A fair point.  It seems like it would be a lot easier to scratch and file the reeds without having to deal with the clearance issues of having the blocks installed, and it being my first time, I correlate "ease" with "likelihood of success."

Yes - tuning reeds on the block, outside the box, is quite a bit of faffing about, what with allowing for tuning corrections, etc., BUT you definitely have more room to work and you can see more easily what you are doing. For beginners learning tuning skills, I think this a really good way to start off. It might be slow but it does work.

As I have gradually improved my skills and confidence over the last few years (thanks to fantastic advice as always from Theo and Rees (:)  :|glug ) then yes, I now do more of my tuning in the box as Theo describes. But the 'on the block, outside the box' method is still really useful at times, e.g. if space inside the box is really crowded with multiple reed blocks. I like to think the two methods complement each other.

Tuning inside the box is still likely to need some off-set corrections, although much less than when working outside the box. The true pitch of a reed only becomes fully apparent when the box is fully re-assembled and everything is tight and snug. Even leaving out some bellows pins can make a difference.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Project box
« Reply #128 on: May 05, 2016, 02:30:09 PM »

If you are planning a wet tuning then the difference between pitches inside and outside the box become less and less relevant as you go to more tremolo.  So if you are doing a Hohner type tremolo just tune everything outside the box, forget about the slight differences in pitch and forget about tuning to offsets, Just listen to the sound once the box is the-assembled.  I will be very surprised if you hear anything untoward.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #129 on: May 05, 2016, 11:22:57 PM »

Isn't this site just great? I'm drinking in all this info for when I get to make a start on my 3-stop project. (If and when I pluck up the courage!)

It is truly great.  The level of expertise and engagement here is just baffling.  I'm so grateful for all the advice and call-outs - it's really invaluable.

As far as my progress, I've decided to go ahead and calculate the offsets for all reeds, tune them on the tuning bellows, and make final adjustments inside the box.  Despite the extra process, this seems the best way forward from here to me.  At any rate, I'll know first hand the difference in difficulty of tuning inside and outside the instrument, and start building that personal experience Theo mentioned :)

For anybody who's interested, I've updated the google sheet for the Bb Row.

To Lester's point:
You need to concentrate on getting as close as possible but fiddling with sub cent tuning is a waste of time.

Yes, I understand this.  I put the precise numbers down as targets because it's easy to do so.  I won't be going back and forth with scratcher and file chasing after hundreths of hertz.

Anyway, having settled on a plan I have now tuned my first few reeds, and it's really not too hard.
Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Project box
« Reply #130 on: May 06, 2016, 08:45:18 AM »

it`s funny that over the past 4 odd years I`ve become comfortable with doing Waxing, Valving, pallet felting, leak chasing and repairing, cosmetics, even bellows repairs, action repairs and replacing reed tongues, rebuilding air buttons, replacing fondo facings etc ........... but tuning has eluded me, just can`t get the hang of it
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #131 on: May 09, 2016, 05:38:24 PM »

I've been working on tuning reeds in spare moments over the last few days.  I'm almost through the Bb block - here are some photos and explanation of the process.  This is my first attempt at tuning, so I'm sure there is lots of room for improvement, but I'm at least getting the reeds to the pitches I want on the tuning bellows.

The tools, from the kit sold my Charlie Marshall.  From left to right: reed pinger/steady, file, reed scratcher, reed lifter.



Tuning the reeds involves removing material from the reed at it's tip (to raise pitch) or it's base (to lower pitch).  To raise the pitch of a "pull" reed, I use the scratcher to push the reed through the slot from the inside:


Then I insert the steady under the reed tongue and withdraw the scratcher:


And then file the tip of the reed as it rests flat against the steady:



The most usual problems I encountered were:

  • Bent or creased a valve with careless action of the file.  Solution is to affix a new valve.
  • Pushed the reed tongue out of alignment while filing.  Solution is to re-align the reed.  On pull reeds this means removing the reed from the block.
  • Roughed up the edges of the reed tongue in filing, resulting in a "fuzzy" sound from the reed.  Solution is to gently deburr the edges with a file or some carborundum paper.

I've found the trickiest action is to flatten the pull reeds, particularly the small ones.  You can only get the steady in so far, and it is hard to put scratches far enough back without bending  the reed.

If the reed blocks were installed, pushing reeds through with the scratcher would be impossible (or at least impractical), in which case the reed lifter could be used.  I practiced this a bit just to get the hang of it.  Basically, you just push the hook down through the adjacent reed slot (displacing the reed):


And then twist the reed lifter, such that the end of the hook pushes the target reed up through the slot:


At this point, the steady can be inserted and the reed lifter removed.

I have yet to encounter any insurmountable difficulties, and though the process is tedious, it gets easier with practice.  Comments, criticism, tips, and suggestions all gratefully accepted. 
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Project box
« Reply #132 on: May 09, 2016, 06:38:39 PM »

Quote
The most usual problems I encountered were:

Bent or creased a valve with careless action of the file.  Solution is to affix a new valve.
Pushed the reed tongue out of alignment while filing.  Solution is to re-align the reed.  On pull reeds this means removing the reed from the block.
Roughed up the edges of the reed tongue in filing, resulting in a "fuzzy" sound from the reed.  Solution is to gently deburr the edges with a file or some carborundum paper.

I've found the trickiest action is to flatten the pull reeds, particularly the small ones.  You can only get the steady in so far, and it is hard to put scratches far enough back without bending  the reed.

1. The diamond files supplied by Charlie Marshall are really too coarse a grade of grit for filing reed tongues, other than the very largest reeds (e.g. the bass reeds or where there is a brass weight soldered on the reed tongue.

The coarse grit (120 grade) means there is an increased risk of the problems you mention, such as catching the valves with the file, burring the edges of the reed tongue and, if the file catches strongly on the tip of the reed tongue, pushing it out of alignment. It's better to use a fine, high-quality steel Swiss needle file, or if you want to use a diamond file, get one which is finer (400 grade). I get mine from ArcEuroTrade here:
http://www.arceurotrade.co.uk/Catalogue/Diamond-Tools/Diamond-Needle-Files/5pc-Diamond-Needle-File-Set-2x100mm

2. To flatten the pull reeds, all you need to do is to use the reed scratcher through the slot and make a scratch(es) by gently pushing the scratcher against the spring resistance of the reed tongue from the belly of the reed towards the rivet end - no need to use a steady. But you must ensure your scratcher has a sharp right-angled edge at the tip (not a needle point and not rounded). You will need to frequently touch up the tip of the scratcher on an oilstone or diamond plate (also obtainable from ArcEurotrade).
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #133 on: May 09, 2016, 06:58:36 PM »

Great advice - thank you, Steve.

Seeing your comment I switched over to some inexpensive needle files I had in reach.  They work way better.
Logged

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Project box
« Reply #134 on: May 09, 2016, 07:37:05 PM »

I have a needle file that comes to a point, it works very well. Another thought, to flatten a reed:

Thin piece of wood to suit reed size (one in pic is about 1.5mm wide)

Angle or round the end with some sandpaper.
Put some contact adhesive (Bostik) on the end, press against some wet and dry* (240 works for me, 360 is arguably more therapeutic) to transfer some glue. When glue is nearly dry, usual contact adhesive routine, join the two and trim with a craft knife or scalpel.
Slip it under the valve until it stops, back off a bit (practice) and file away.

It's not as fast as scratching, but it's still fairly quick, easier and more controlled. It doesn't risk the set of the reed if you're having a clumsy day, it's kind to the valve (ditto), and you don't need to support the reed. Gentle pressure works fine.
I've just used this one to bring some reeds down 8 to 10 cents, I was struggling with the scratch tools, but it also does much smaller amounts quite controllably.
The life varies with the size of reed and how far you need to go, but maybe two reeds or more.
When the abrasive is worn, pull it off and stick some more on. This particular stick has done 10 reeds.

Sounds a faff but you could make several in the time it took to type this. It also helps if you squirrel away all but the tiniest wood offcuts when doing any sawing.

*the smooth side, not the grit side. But you knew that  ::)
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Project box
« Reply #135 on: May 09, 2016, 08:13:24 PM »

I use these on small/tiny reeds   http://www.axminster.co.uk/axminster-detail-sanding-pen-kit-410218
and these on bigger reeds  http://www.axminster.co.uk/vallorbe-swiss-saw-files-ax22603 but it looks as if they are no longer available from Axminster   :(.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Project box
« Reply #136 on: May 09, 2016, 11:31:11 PM »

Another thought, to flatten a reed:

Thin piece of wood to suit reed size (one in pic is about 1.5mm wide)

Angle or round the end with some sandpaper.
Put some contact adhesive (Bostik) on the end, press against some wet and dry* (240 works for me, 360 is arguably more therapeutic) to transfer some glue. When glue is nearly dry, usual contact adhesive routine, join the two and trim with a craft knife or scalpel.
Slip it under the valve until it stops, back off a bit (practice) and file away.

When using this sort of tool through the reed plate slot to file the underneath reeds, you need to be very careful that the edges of your wet-and-dry strip do not come into contact with the sides of the slot. It's easy to inadvertently damage/enlarge the relatively soft sides of the slot, which will impair the reed tongue's response. That's why a proper scratcher is good. The sides of the scratcher are smooth and will not damage the reed plate slot nor the valve.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Project box
« Reply #137 on: May 09, 2016, 11:33:59 PM »

Not if you are careful they won't.  It is quite easy for a scratcher to slip sideways and gouge the wall of the vent.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Project box
« Reply #138 on: May 09, 2016, 11:40:26 PM »

Theo's comment is a timely reminder of how to approach all reed work, using any sort of tool: be careful.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Jef

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Project box
« Reply #139 on: May 10, 2016, 03:19:26 PM »

Theo's comment is a timely reminder of how to approach all reed work, using any sort of tool: be careful.

Indeed.  The corollary is, I think, is to choose the tool that best facilitates careful use.  Having switched over to the small (140mm) pattering files, I feel like I'm working with the reeds rather than mounting an assault on them.
Logged
Pages: 1 2 3 4 5 6 [7] 8 9   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal