Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Noisy valves on new reeds  (Read 3149 times)

0 Members and 1 Guest are viewing this topic.

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Noisy valves on new reeds
« on: March 01, 2016, 02:12:02 PM »

The box I built with Emmanuel is an L/M G/C, so it's pretty low-pitched. Pretty much the entire low octave and the bass reeds suffer from quite a lot of valve noise, more so than on other G/C instruments I've tried with a low register. The reeds are Binci a mano, and mostly have the plastic valves, with those faux-leather (vileda?) valves on any reed that has a weight on the tip.

Understandably the valves are pretty massive for some of these reeds on account of how big they are, but is there anything I can do to at least reduce the noise a little? I suspect it could do with a bit of a tune-up sometime later this year anyway as the reeds have settled a bit since it was built.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Noisy valves on new reeds
« Reply #1 on: March 01, 2016, 02:47:17 PM »

If the lower reeds have vileda valves then they might need to be replaced.  It's more likely that they have a grey leather layer with a couple of plastic layers on top.  These can be adjusted by putting a slight kink in the plastic layers so that they press a little more in the leather.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: Noisy valves on new reeds
« Reply #2 on: March 01, 2016, 03:00:48 PM »

Ah thanks Theo, you're right; they appear to actually be grey leather now I look closer. One of them also has a kink in it, so I'll test how that one responds vs the others and try adding kinks to the other slow responding ones.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Noisy valves on new reeds
« Reply #3 on: March 01, 2016, 04:35:33 PM »

There was one course where Emmanuel mistakenly ordered all the reeds without valves.  He and I then had to work together in the fortnight leading up to the course to find enough valves and fit them.  Usually the reeds used on the course are valved  in the traditional way with leather.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: Noisy valves on new reeds
« Reply #4 on: March 01, 2016, 05:06:11 PM »

Oof, that sounds like fun :o
Yeah these ones are leather. I've just added a kink into all of the leather-based ones and they seem to sit a little closer to the plate now, which is good. However I've now figured out that those ones are not the main noise-causers, and instead it's the larger all-plastic valves which are the most audible. There's 4 plates in the lower octave in the L reeds which seem to be the ones making the most valve noise, and I suspect this is true of the higher of the two bass reeds. The plastic on these valves seems very thin and with quite short springs for what are quite large reeds, though my experience with revalving is limited to a couple of boxes so far:



Saying that, they do seem to close fine, they're just really loud. I could experiment with replacing them, though I only have some vileda valves lying around that I could cut to size. I suspect it'd affect the reed response a bit?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Noisy valves on new reeds
« Reply #5 on: March 01, 2016, 05:20:56 PM »

Big plastic valves are noisy compared with leather, so your experience is typical.

Leather is much better than vileda which can be a bit sluggish to respond.  So for the best results replace all the noisy plastic with leather.  Leather valves will differ in how easily they open compared with plastic, which can make a small difference to the pitch of the reed. But the lack of plastic rattle will probably outweigh any small changes in tuning.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: Noisy valves on new reeds
« Reply #6 on: March 01, 2016, 05:31:48 PM »

Thanks for the advice Theo. It'll need tuning sometime soon anyway so a pitch change wouldn't be a huge issue. Would the leather valves from Charlie Marshall be suitable (e.g. these), or is there somewhere else to order them from?

And yeah I'd really like to reduce the valve noise on this, as it's otherwise a really nice box to play (:)
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Noisy valves on new reeds
« Reply #7 on: March 01, 2016, 05:57:38 PM »

Thanks for the advice Theo. It'll need tuning sometime soon anyway so a pitch change wouldn't be a huge issue. Would the leather valves from Charlie Marshall be suitable (e.g. these), or is there somewhere else to order them from?

And yeah I'd really like to reduce the valve noise on this, as it's otherwise a really nice box to play (:)

I've found the leather valves as supplied by Charlie Marshall to be absolutely fine. I measure the lengths of valves required and make a list for Charlie, then add a few extra of each size (to allow for the odd mistake/wastage/accident -  whoops!  ::) ).

I also order the springs and dots separately (i.e. not fixed to the valves already). It is easy to glue them in place and buying them loose allows you more flexibility in getting the valves/springs exactly the right length for your particular reeds.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: Noisy valves on new reeds
« Reply #8 on: March 01, 2016, 06:41:05 PM »

Yeah I may have already accidentally waxed a valve closed on another box ::)
I need to order some more valves to restore another Erika I picked up (perfect condition Bb/Eb, woop), so might as well do that one with leather at the same time. I haven't used the springs before, are there any guidelines as to what lengths/sizes to use for different sized valves?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Noisy valves on new reeds
« Reply #9 on: March 01, 2016, 06:56:50 PM »

I like to use plastic valves on about the top octave and a half of a DG. You get slightly more volume and brightness,  and the small plastic valves don't make any noise that I can hear. The natural variability of leather can also be a bit of s problem on the smallest reeds.

With the helper springs the principle to stick to is to use only just enough extra force to close the valve smoothly.  So use the lightest helper spring you can, and only use them where the valve leather needs help.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: Noisy valves on new reeds
« Reply #10 on: March 01, 2016, 07:21:34 PM »

Aye, I think I'll keep the top octave in plastic, as those don't seem to make any noise that I can hear. I'll probably do the same for the Bb/Eb as well then, and order some more plastic valves to do the upper part of that.

Thanks for the tips! I'll update this when I've had a go at switching them out ;D
Logged

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: Noisy valves on new reeds
« Reply #11 on: March 07, 2016, 03:52:45 PM »

Just finished revalving the treble side reeds, and it has made a huge difference; I can actually play down the bottom end of it without getting annoyed ;D
Bit of an interesting selection of valves going on now, but it seems to have the same response along the row, which is nice, and no discernable pitch shift.



Think I'll take a stab at the bass end tomorrow.
Logged

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: Noisy valves on new reeds
« Reply #12 on: March 08, 2016, 04:54:06 PM »

Hmm, I've been adjusting the new valves today, as I seem to get a rattle on some of the helper springs. Is this caused by the spring being too strong for the valve? I seem to have solved it on some of them by switching them for a lighter spring, though I'm not sure if that'll work for the largest ones. It makes a sound a bit like a bee trapped in the reed chamber; I think it's the spring slapping against the valve leather. Alternatively are there any adjustments I should make to the spring (i.e. bending it one way or the other) or the valve itself?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Noisy valves on new reeds
« Reply #13 on: March 08, 2016, 05:06:32 PM »

Unlikely to be the helper sorry big hitting the valve. It is more likely to be the reed tongue hitting the valve.
Only fit helper springs if the valves misbehave without them. If you do fit springs start with the thinnest available.  I think the thinnest is 0.5mm wide.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: Noisy valves on new reeds
« Reply #14 on: March 08, 2016, 05:15:51 PM »

Ah cool, thanks Theo. I've probably wasted a few springs in that case ;D
It mostly only seems to occur when using low airflow, so I thought the valves might not have been sealing correctly, but I guess it'd also be just as likely to be stalling the reed if the spring was too strong?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Noisy valves on new reeds
« Reply #15 on: March 08, 2016, 06:07:38 PM »

If it's only at low airflow then my diagnosis is probably wrong! 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: Noisy valves on new reeds
« Reply #16 on: March 08, 2016, 07:37:51 PM »

Ooh discovered the cause of why one reed, which I hadn't revalved, was making a rattling noise. Because it's a rather large reed, it was transfering quite a lot of vibrations through the screw to the re-valved reedplate next to it, causing the metal spring to vibrate. A downside to the screw method of mounting reeds instead of waxing I guess. I'm going to try insulating the second plate somehow, maybe a small washer.

Edit: Bah, or not. Very frustrating debugging valve issues on this box, I found it much easier on the A/D Hohner I did beforehand ???

Edit 2: Or perhaps my first hunch was correct. Removing this screw solves the rattle:



I tried insulating it but I think it then caused the plates to rattle against it as it wasn't snug. Might just leave it out for the moment to see if that solves the remaining issues.
« Last Edit: March 08, 2016, 07:58:26 PM by robotmay »
Logged

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Noisy valves on new reeds
« Reply #17 on: March 08, 2016, 07:53:40 PM »

I'm going to try insulting the second plate somehow

Yep - that'll teach it to behave itself!   >:E ;D
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: Noisy valves on new reeds
« Reply #18 on: March 08, 2016, 07:58:04 PM »

Haha, I've managed to make that typo twice now! Too much time faffing with valves today :Ph
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Noisy valves on new reeds
« Reply #19 on: March 08, 2016, 08:13:20 PM »

Reed plates have to be held securely so leaving out screws is not to be encouraged.
If the noise come or goes with screw tightening then the probable cause is nothing to do with valves.  Too much pressure from screws near the centre of the long side of a reed plate will deform the reed plate sufficiently that the tongue strikes the edge of the vent. If you experiment with how tightly you turn the screw your should be able to fix it.  Also check that the reed plate is supported by wood along both long sides.  If it is not sitting on a smooth firm surface then it will deform more easily under screw pressure.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal