Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: air buttons, bar type  (Read 1173 times)

0 Members and 1 Guest are viewing this topic.

RonPimm

  • New Starter
  • Offline Offline
  • Posts: 1
air buttons, bar type
« on: March 03, 2016, 12:10:10 PM »

I have a slight disability in the left hand which results in restricted thumb movement and strength. Playing my H. Pokerwork is Ok but tiring/painful after a while. I am trying a Saltarelle at the moment which I like but have found a problem with the air button. It is very difficult to have my hand in the right position to play the bass/chord buttons and simultaneously operate the air button. I notice that the air button is above the surrounding surface by 7 or 8mm, although it only takes about 1mm of the initial movement to operate it. I wondered if it could be modified so that the button is proud by only about 3mm. Theo says  it can be done but I wondered if there is anyone out there who has modified a bar type airbutton in this way and how they found the modification.
Logged

Phil B

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 118
Re: air buttons, bar type
« Reply #1 on: March 06, 2016, 08:28:14 PM »

I have reduced the height of the air button on two Saltarelle's and rounded the leading edge so you can slide your thumb over to operate it rather than having to lift the thumb up and have personally found it a vast improvement.
The mod is reversible, if it dose not work for you, with a new piece of suitable wood and modern glues
Logged

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: air buttons, bar type
« Reply #2 on: March 06, 2016, 09:45:00 PM »

With the Saltarelle mechanism there are 2 ways you could go to reduce the travel on the air button:

Probably the easiest would be to gently bend the wire that links the button to the hinge so that it sinks inside the bass casing (this will only work if, like mine your button is linked by wire and there is enough room inside the box)

If that fails you could physically reduce the thickness of the wood the air button is made from by using a rasp and then sanding down - taking care not to weaken it too much.
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: air buttons, bar type
« Reply #3 on: March 06, 2016, 11:18:57 PM »

AS above but if you have the capability, make a new button to experiment with leaving the original to replace should it not work out or if you sell the box in the future - best of luck with it  (:)
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: air buttons, bar type
« Reply #4 on: March 07, 2016, 09:46:30 AM »


The bar type air button on my Hascy is a dream to operate.
The Hascy button is almost level with the casework at the chin end and gets thicker as you go down in a roughly triangular shape. Therefore to operate it your thumb slides down it and the wedge shape means the more 'down' you go the greater the button operates as the wedge shape increases the mechanical advantage.
As Broadland Boy says, if you can make a new button to work like this, then the original can stay with the box if you decide to pass it on later.
Good luck
Q
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal